ASTM E1708-19
(Practice)Standard Practice for Electronic Interchange of Color and Appearance Data
Standard Practice for Electronic Interchange of Color and Appearance Data
SIGNIFICANCE AND USE
5.1 This practice should be used by manufacturers of color-measuring instruments and developers of software when the transmission of color and appearance data is desired between instruments or computers and where ASCII files are the desired method of transfer.
5.2 The method of transmission may be via direct connection, modem, or the transfer of electronic media, for example, by floppy disk transfer.
5.3 The practice lends itself to the transmission of either a single record of data or multiple record files.
5.4 Examples of files generated in this practice are contained in Fig. X1.1 and Fig. X2.1 of Appendix X1 and Appendix X2.
SCOPE
1.1 This practice covers procedures to be used in the electronic exchange of color and appearance data between users, by either modem or the physical transfer of electronic media. It is intended for use by manufacturers of color-measuring instruments and developers of software so that any instrument may acquire data for its use that may have been measured on an instrument of another manufacturer, at another place, or at another time.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1708 − 19
Standard Practice for
1
Electronic Interchange of Color and Appearance Data
This standard is issued under the fixed designation E1708; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.2.2 keyword, n—in electronic interchange, an alphanu-
mericdesignatorthatdefinesthenatureornumberoffollowing
1.1 This practice covers procedures to be used in the
data fields.
electronic exchange of color and appearance data between
3.2.2.1 Discussion—The word is used in its ordinary dic-
users, by either modem or the physical transfer of electronic
tionary sense in Section 7.
media. It is intended for use by manufacturers of color-
3.2.3 white space, n—a valid character representation that
measuring instruments and developers of software so that any
does not generate a printable character in a file.
instrument may acquire data for its use that may have been
3.2.3.1 Discussion—ValidASCII white space characters are
measured on an instrument of another manufacturer, at another
space (decimal 32), carriage return (decimal 13), form feed
place, or at another time.
(decimal 12), vertical tab (decimal 11), newline (decimal 10),
1.2 This standard does not purport to address all of the
and horizontal tab (decimal 9).
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
4. Summary of Practice
priate safety, health, and environmental practices and deter-
4.1 Users of this practice are given a mandatory list of
mine the applicability of regulatory limitations prior to use.
keywords. The user fills out the list with the data values
1.3 This international standard was developed in accor-
associated with each keyword. The user may then select from
dance with internationally recognized principles on standard-
an optional list of keywords. The user then associates with
ization established in the Decision on Principles for the
these keywords the data values required to be transmitted.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
4.2 The keywords are used at the receiving end of the
Barriers to Trade (TBT) Committee.
transmission to decode the format and number of data values
present in the transmission.
2. Referenced Documents
2 5. Significance and Use
2.1 ASTM Standards:
5.1 This practice should be used by manufacturers of
E284 Terminology of Appearance
color-measuring instruments and developers of software when
the transmission of color and appearance data is desired
3. Terminology
between instruments or computers and where ASCII files are
3.1 DefinitionsoftermsinTerminologyE284areapplicable
the desired method of transfer.
to this practice.
5.2 The method of transmission may be via direct
3.2 Definitions of Terms Specific to This Standard:
connection, modem, or the transfer of electronic media, for
3.2.1 data value identifier, n—a keyword that identifies the
example, by floppy disk transfer.
contents of a data field and, by definition, signals the data type
5.3 The practice lends itself to the transmission of either a
of the field as string, integer, or floating point.
single record of data or multiple record files.
5.4 Examples of files generated in this practice are con-
1 tained in Fig. X1.1 and Fig. X2.1 of Appendix X1 and
This practice is under the jurisdiction of ASTM Committee E12 on Color and
Appearance and is the direct responsibility of Subcommittee E12.04 on Color and
Appendix X2.
Appearance Analysis.
Current edition approved Nov. 1, 2019. Published November 2019. Originally
6. Procedure
approved in 1995. Last previous edition approved in 2019 as E1708 – 14 (2019).
DOI: 10.1520/E1708-19.
6.1 Prepare a file using ASCII code that consists of the
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
mandatorykeywordlistfollowedbytheassociateddatavalues.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Each keyword and each data value is delimited by white space.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. The record may be organized into logical units associated with
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1708 − 19
each keyword by using the carriage return character for the 6.3.1 SPECIMEN_ID, CS—This identifies the specimen
white space delimiter at the end of the data values associated that the data represent.
with any keyword.
6.3.2 STR
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E1708 − 14 (Reapproved 2019) E1708 − 19
Standard Practice for
1
Electronic Interchange of Color and Appearance Data
This standard is issued under the fixed designation E1708; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers procedures to be used in the electronic exchange of color and appearance data between users, by either
modem or the physical transfer of electronic media. It is intended for use by manufacturers of color-measuring instruments and
developers of software so that any instrument may acquire data for its use that may have been measured on an instrument of
another manufacturer, at another place, or at another time.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E284 Terminology of Appearance
3. Terminology
3.1 Definitions of terms in Terminology E284 are applicable to this practice.
3.2 Definitions of Terms Specific to This Standard:
3.2.1 data value identifier, n—a keyword that identifies the contents of a data field and, by definition, signals the data type of
the field as string, integer, or floating point.
3.2.2 keyword, n—in electronic interchange, an alphanumeric designator that defines the nature or number of following data
fields.
3.2.2.1 Discussion—
The word is used in its ordinary dictionary sense in Section 7.
3.2.3 white space, n—a valid character representation that does not generate a printable character in a file.
3.2.3.1 Discussion—
Valid ASCII white space characters are space (decimal 32), carriage return (decimal 13), form feed (decimal 12), vertical tab
(decimal 11), newline (decimal 10), and horizontal tab (decimal 9).
1
This practice is under the jurisdiction of ASTM Committee E12 on Color and Appearance and is the direct responsibility of Subcommittee E12.04 on Color and
Appearance Analysis.
Current edition approved May 1, 2019. Published May 2019XXXX 2019. Originally approved in 1995. Last previous edition approved in 20142019 as
E1708 – 14.E1708 – 14 (2019). DOI: 10.1520/E1708-14R19.10.1520/E1708-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
E1708 − 19
4. Summary of Practice
4.1 Users of this practice are given a mandatory list of keywords. The user fills out the list with the data values associated with
each keyword. The user may then select from an optional list of keywords. The user then associates with these keywords the data
values required to be transmitted.
4.2 The keywords are used at the receiving end of the transmission to decode the format and number of data values present in
the transmission.
5. Significance and Use
5.1 This practice should be used by manufacturers of color-measuring instruments and developers of software when the
transmission of color and appearance data is desired between instruments or computers and where ASCII files are the desired
method of transfer.
5.2 The method of transmission may be via direct connection, modem, or the transfer of electronic media, for example, by
floppy disk transfer.
5.3 The practice lends itself to the transmission of either a single record of data or multiple record files.
5.4 Examples of files generated in this practice are contained in Fig. X1.1 and Fig. X2.1 of Appendix X1 and Appendix X2.
6. Procedure
6.1 Prepare a file using ASCII code that consists of the mandatory keyword list followed by the associated data va
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.