ASTM A888-04

Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

SCOPE
1.1 This specification covers cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, principal dimensions, and dimensional tolerances for hubless cast iron soil pipe and fittings. These pipe and fittings are not intended for pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the requirements given herein.1.2.1 Lengths: FiguresEDP Identification Numbers for Hubless Pipe110 ft (3.0 m) in sizes 1 ½ , 2, 3, 4, 5, 6, 8, 10, 12, and 15 inch.1, 2Method of Specifying Fittings3
1.2.2Fittings: Quarter Bend4Quarter Bend, Reducing5Quarter Bend, With Side Opening6Quarter Bend, With Heel Opening7Quarter Bend, Tapped8Quarter Bend, Double9Quarter Bend, Long10Short Sweep11Long Sweep12Long Sweep, Reducing13Fifth Bend14Sixth Bend15Eighth Bend16Eighth Bend Long17Sixteenth Bend18Sanitary Tee19Sanitary Tee With Side Opening20Sanitary Tee With 2 in. Side Opening R or L/R and L21Sanitary Tee, New Orleans Special With Side Opening22Sanitary Tee With 45 Side Openings and New Orleans23Sanitary Special Tee Tapped24Sanitary Tapped Tee, Horizontal Twin25Sanitary Tapped Tee, Double Vertical26Y Branch27Y Branch, Double28Y Branch, Upright29Upright Y Wide Center Florida Special30Y Branch, Combination 1/8 Bend 31Y Branch, Combination 1/8 Bend Double32Sanitary Cross33Sanitary Cross With Side Opening34Sanitary Cross, New Orleans, With Side Openings35Sanitary Cross, New Orleans, With 45 Special andRegular Side Openings 36Sanitary Cross, Tapped37Test Tee38Tapped, Extension Piece39Increaser-Reducer40Increaser-Reducer, Short41Tapped Adapter42Blind Plug43Iron Body Cleanout-Tapped44P Trap 45P Trap, Long46P Trap, Long-Tapped47P Trap, Deep Seal48P Trap, Reducing49P Trap, With Primer50P Trap, With Tapped Inlet51Hub Adapter52Tapped Inlet, Double53Modified Combination Wye and 1/8 Bend, Double54Modified Combination Wye and 1/8 Bend, Double, Extended55Regular or Extended Left or Right Regular or ExtendedDouble56Regular or Extended Left or Right Regular or ExtendedDouble57Two-Way Cleanout58Twin Cleanout59Closet Bend, Regular and Reducing60Closet Flange61Tapping Bosses62
1.3 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses shall be for information only.
Note 1—The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

General Information

• Status: Historical
• Publication Date: 31-Dec-2003
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 91.140.80 - Drainage systems
• Technical Committee: A04 - Iron Castings
• Drafting Committee: A04.12 - Pipes and Tubes

Relations

• Replaces: ASTM A888-03 - Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
• Effective Date: 01-Jan-2004
• Replaced By: ASTM A888-04a - Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
• Effective Date: 01-Sep-2004
• Referred By: ASTM C1540-20 - Standard Specification for Heavy-Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
• Effective Date: 01-Jan-2004
• Referred By: ASTM A1056-20 - Standard Specification for Cast Iron Couplings Used for Joining Hubless Cast Iron Soil Pipe and Fittings
• Effective Date: 01-Jan-2004
• Referred By: ASTM A1111-22 - Standard Specification for Cast Iron Closet Flanges for Use with Cast Iron Soil Pipe and Fittings in Gravity Flow Plumbing Drain, Waste, and Vent Sanitary Applications
• Effective Date: 01-Jan-2004
• Referred By: ASTM C1277-20 - Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings
• Effective Date: 01-Jan-2004

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 888 – 04
Standard Specification for
Hubless Cast Iron Soil Pipe and Fittings for Sanitary and
1
Storm Drain, Waste, and Vent Piping Applications
This standard is issued under the fixed designation A 888; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
Short Sweep Fig. 12
Long Sweep Fig. 13
1.1 This specification covers hubless cast iron soil pipe and
Long Sweep, Reducing Fig. 14
fittings for use in gravity flow applications. It establishes
Fifth Bend Fig. 15
Sixth Bend Fig. 16
standards covering material, manufacture, mechanical and
Eighth Bend Fig. 17
chemical properties, dimensions, coating, test methods, inspec-
Eighth Bend Long Fig. 18
tion, certification and product marking for hubless cast iron soil
Sixteenth Bend Fig. 19
Sanitary Tee Fig. 20
pipe and fittings. These pipe and fittings are intended for
Sanitary Tee With Side Opening Fig. 21
non-pressure applications, as the selection of the proper size
Sanitary Tee With 2 in. Side Opening R or L/R and L Fig. 22
for sanitary drain, waste, vent, and storm drain systems allows Sanitary Tee, New Orleans Special With Side Opening Fig. 23
Sanitary Tee With 45° Side Openings and New Orleans Fig. 24
free air space for gravity drainage.
Sanitary Special Tee Tapped Fig. 25
1.2 The EDP/ASA numbers indicated in this section repre-
Sanitary Tapped Tee, Horizontal Twin Fig. 26
sent a Uniform Industry Code adopted by the American Supply Sanitary Tapped Tee, Double Vertical Fig. 27
Y Branch Fig. 28
Association (ASA). A group designation prefix, 022, is as-
Y Branch, Double Fig. 29
signed to hubless products, followed by the four-digit identi-
Y Branch, Upright Fig. 30
fication assigned to individual items and a check digit. This Upright Y Wide Center Florida Special Fig. 31
1
Y Branch, Combination ⁄8 Bend Fig. 32
system has been instituted to facilitate EDP control through
1
Y Branch, Combination ⁄8 Bend Double Fig. 33
distribution channels, and be used universally in ordering and
Sanitary Cross Fig. 34
specifying product items. Those items with no EDP numbers Sanitary Cross With Side Opening Fig. 35
Sanitary Cross, New Orleans, With Side Openings Fig. 36
are either new, special or transitory and will be assigned
Sanitary Cross, New Orleans, With 45° Special and Fig. 37
numbers on subsequent prints of this specification.
Regular Side Openings
Sanitary Cross, Tapped Fig. 38
1.3 This specification covers pipe and fittings of the follow-
Test Tee Fig. 39
ing patterns and applies to any other patterns that conform with
Tapped, Extension Piece Fig. 40
2
the applicable requirements given herein.
Increaser-Reducer Fig. 41
Increaser-Reducer, Short Fig. 42
1.3.1 Lengths:
Tapped Adapter Fig. 43
Figures
Blind Plug Fig. 44
EDP/ASA Identification Numbers Fig. 1
Iron Body Cleanout-Tapped Fig. 45
for Hubless Pipe
P Trap Fig. 46
10 ft (3.0 m) in sizes and 5 ft. (1.5 m) Fig. 1, Fig. 2
P Trap, Long Fig. 47
1
⁄2 ,2,3,4,5,6,8,
1
P Trap, Long-Tapped Fig. 48
10, 12, and 15 inch.
P Trap, Deep Seal Fig. 49
Method of Specifying Fittings Fig. 3
P Trap, Reducing Fig. 50
P Trap, With Primer Fig. 51
1.3.2 Fittings:
P Trap, With Tapped Inlet Fig. 52
Quarter Bend Fig. 5
Hub Adapter Fig. 53
Quarter Bend, Reducing Fig. 6
Tapped Inlet, Double Fig. 54
Quarter Bend, With Side Opening Fig. 7 1
Modified Combination Wye and ⁄8 Bend, Double Fig. 55
Quarter Bend, With Heel Opening Fig. 8 1
Modified Combination Wye and ⁄8 Bend, Double, Ex- Fig. 56
Quarter Bend, Tapped Fig. 9
tended
Quarter Bend, Double Fig. 10
Regular or Extended Left or Right Regular or Extended Fig. 57
Quarter Bend, Long Fig. 11
Double
Regular or Extended Left or Right Regular or Extended Fig. 58
Double
Two-Way Cleanout Fig. 59
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron
Twin Cleanout Fig. 60
Castings and is under the direct responsibility of Subcommittee A04.12 on Pipes and
Closet Bend, Regular and Reducing Fig. 61
Tubes.
Closet Flange Fig. 62
Current edition approved Jan. 1, 2004. Published February 2004. Originally
Tapping Bosses Fig. 63
approved in 1990. Last previous edition approved in 2003 as A 888 – 03.
2
Reprinted with permission from Cast Iron Soil Pipe Institute.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A888–04
1.4 The values stated in inch-pound units shall be regarded DBL—double
as the standard. The values given in parentheses shall be for EDP—electronic data processing
information only. Metric conversions in Table 1 and Table 2 are EXT—extended
...