iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5248-04(2010)

(Specification)

Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane

Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane

ABSTRACT
This specification covers the three grades of 1,1,2- trichloro 1,2,2 trifluoroethane typically needed in various industries. This may be a reference for 1,1,2-trichloro 1,2,2- trifluoroethane recovery programs. The three classifications are as follows: Type I - generally recognized for use in precision applications; Type II - used for less demanding precision applications; and Type III - general-purpose technical grade. Materials shall be tested and the individual grades shall conform to specified values of specific gravity, chloride content, acid number, non-volatile residue content, water content, 1,1,2-trichloro 1,2,2- trifluoroethane content, 1,1,1- trichloroethane content, color, and appearance.
SCOPE
1.1 This specification covers the three grades of 1,1,2-trichloro 1,2,2-trifluoroethane typically needed in various industries. It may be used as a reference document by purchasers or by persons establishing in-house, 1,1,2-trichloro 1,2,2-trifluoroethane recovery programs.

General Information

Status
Historical
Publication Date
31-Jan-2010
ICS
71.080.10 - Aliphatic hydrocarbons
Technical Committee
D26 - Halogenated Organic Solvents and Fire Extinguishing Agents
Drafting Committee
D26.02 - Vapor Degreasing
Current Stage
Ref Project

Relations

Replaces
ASTM D5248-04 - Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane
Effective Date
01-Feb-2010
Replaced By
ASTM D5248-04(2015) - Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane
Effective Date
01-Jun-2015

Buy Standard

ASTM D5248-04(2010) - Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-TrifluoroethaneASTM D5248-04(2010) - Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane
PreviousNext
Technical specification
ASTM D5248-04(2010) - Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5248 −04(Reapproved 2010)
Standard Specification for
Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane
This standard is issued under the fixed designation D5248; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D3401 Test Methods for Water in Halogenated Organic
Solvents and Their Admixtures
1.1 This specification covers the three grades of 1,1,2-
2 D3443 Test Method for Chloride in Trichlorotrifluoroethane
trichloro 1,2,2-trifluoroethane typically needed in various
D3444 Test Method for Total Acid Number of Trichlorotri-
industries. It may be used as a reference document by purchas-
fluoroethane
ers or by persons establishing in-house, 1,1,2-trichloro 1,2,2-
D3741 Test Methods for Appearance of Admixtures Con-
trifluoroethane recovery programs.
taining Halogenated Organic Solvents
D6806 Practice for Analysis of Halogenated Organic Sol-
2. Referenced Documents
vents and Their Admixtures by Gas Chromatography
2.1 ASTM Standards:
D1064 Test Methods for Iron in Rosin Tall Oil Fatty Acids
3. Classification
and Other Related Products (Withdrawn 2002)
3.1 Type I—Generally recognized for use in precision ap-
D2108 Test Method for Color of Halogenated Organic
plications.
Solvents and Their Admixtures (Platinum-Cobalt Scale)
3.2 Type II—Use for less demanding precision applications.
D2109 Test Methods for Nonvolatile Matter in Halogenated
Organic Solvents and Their Admixtures
3.3 Type III—General-purpose technical grade.
D2111 Test Methods for Specific Gravity and Density of
Halogenated Organic Solvents and Their Admixtures 4. Properties
4.1 Reclaimed 1,1,2-trichloro 1,2,2-trifluoroethane Type I
shall meet the requirements prescribed in Table 1.
This specification is under the jurisdiction of ASTM Committee D26 on
Halogenated Organic Solvents and Fire Extinguishing Agents and is the direct
4.2 Reclaimed 1,1,2-trichloro 1,2,2-trifluoroethane Type II
responsibility of Subcommittee D26.02 on Vapor Degreasing.
shall meet the requirements prescribed in Table 2.
Current edition approved Feb. 1, 2010. Published March 2010. Originally
approved in 1992. Last previous edition approved in 2004 as D5248 – 04. DOI:
4.3 Reclaimed 1,1,2-trichloro 1,2,2-trifluoroethane Type III
10.1520/D5248-04R10.
shall meet the requirements prescribed in Table 3.
1,1,2-trichloro 1,2,2-trifluoroethane: CAS No. 76-13-1.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5. Keywords
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
5.1 1,1,2-trichloro 1,2,2-trifluoroethane ; CFC 113; Type I;
the ASTM website.
4 Type II; Type II
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D5248-04(2020)(Specification)
Standard Specification for Reclaimed 1,1,2-Trichloro 1,2,2-Trifluoroethane

ABSTRACT
This specification covers the three grades of 1,1,2- trichloro 1,2,2 trifluoroethane typically needed in various industries. This may be a reference for 1,1,2-trichloro 1,2,2- trifluoroethane recovery programs. The three classifications are as follows: Type I - generally recognized for use in precision applications; Type II - used for less demanding precision applications; and Type III - general-purpose technical grade. Materials shall be tested and the individual grades shall conform to specified values of specific gravity, chloride content, acid number, non-volatile residue content, water content, 1,1,2-trichloro 1,2,2- trifluoroethane content, 1,1,1- trichloroethane content, color, and appearance.
SCOPE
1.1 This specification covers the three grades of 1,1,2-trichloro 1,2,2-trifluoroethane2 typically needed in various industries. It may be used as a reference document by purchasers or by persons establishing in-house, 1,1,2-trichloro 1,2,2-trifluoroethane recovery programs.  
1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5273-23(Guide)
Standard Guide for Analysis of Propylene Concentrates

SIGNIFICANCE AND USE
4.1 This guide is intended to provide information on the likely composition of propylene concentrates and on probable ways to test them. Since there are currently no ASTM test methods for determining all components of interest, this guide provides information on other potentially available test methods.  
4.2 Although this guide is not to be used for specifications, it can provide a starting point for parties to develop mutually agreed upon specifications which meet their respective requirements. It can also be used as a starting point in finding suitable test methods for determining various components of propylene.
SCOPE
1.1 This guide covers a list of the major grades of propylene concentrates produced in North America. It includes possible components and test methods, both ASTM and other, either actually used, or believed to be in use, to test for these properties. This guide is not intended to be used or construed as a set of specifications for any grade of propylene concentrate.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D7061-23(Test Method)
Standard Test Method for Measuring n-Heptane Induced Phase Separation of Asphaltene-Containing Heavy Fuel Oils as Separability Number by an Optical Scanning Device

SIGNIFICANCE AND USE
5.1 This procedure describes a rapid and sensitive method for estimating the stability reserve of an oil. The stability reserve is estimated in terms of a separability number, where a low value of the separability number indicates that there is a stability reserve within the oil. When the separability number is between 0 to 5, the oil can be considered to have a high stability reserve and asphaltenes are not likely to flocculate. If the separability number is between 5 to 10, the stability reserve in the oil will be much lower. However, asphaltenes are, in this case, not likely to flocculate as long as the oil is not exposed to any worse conditions, such as storing, aging, and heating. If the separability number is above 10, the stability reserve of the oil is very low and asphaltenes will easily flocculate, or have already started to flocculate.  
5.2 This test method can be used by refiners and users of oils, for which this test method is applicable, to estimate the stability reserves of their oils. Hence, this test method can be used by refineries to control and optimize their refinery processes. Consumers of oils can use this test method to estimate the stability reserve of their oils before, during, and after storage.
FIG. 1 Schematic Representation of a Typical Measurement Using an Optical Scanning Device  
5.3 This test method is not intended for predicting whether oils are compatible before mixing, but can be used for determining the separability number of already blended oils. However, oils that show a low separability number are more likely to be compatible with other oils than are oils with high separability numbers.
SCOPE
1.1 This test method covers the quantitative measurement, either in the laboratory or in the field, of how easily asphaltene-containing heavy fuel oils diluted in toluene phase separate upon addition of heptane. This is measured as a separability number (%) by the use of an optical scanning device.  
1.2 The test method is limited to asphaltene-containing heavy fuel oils. ASTM specification fuels that generally fall within the scope of this test method are Specification D396, Grade Nos. 4, 5, and 6, Specification D975, Grade No. 4-D, and Specification D2880, Grade Nos. 3-GT and 4-GT. Refinery fractions from which such blended fuels are made also fall within the scope of this test method.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7266-23(Test Method)
Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (External Standard)

SIGNIFICANCE AND USE
5.1 This test method is suitable for setting specifications on the materials referenced in Table 1 and for use as an internal quality control tool where cyclohexane is produced or is used in a manufacturing process. It may also be used in development or research work involving cyclohexane.  
5.2 This test method is useful in determining the purity of cyclohexane with normal impurities present. If extremely high boiling or unusual impurities are present in the cyclohexane, this test method would not necessarily detect them and the purity calculation would be erroneous.
SCOPE
1.1 This test method covers the determination of the purity of cyclohexane by gas chromatography.  
1.2 This test method is applicable to the measurement of impurities in Table 1. This test method is applicable to samples with concentrations to 400 mg/kg, but may be applicable to a wider range. The limit of detection (LOD) is 1 mg/kg and the limit of quantitation (LOQ) is 3 mg/kg for benzene.
Note 1: The LOD and LOQ were calculated from the ILS data for benzene.  
1.3 The following applies for the purposes of determining the conformance of the test results using this test method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7871-23(Test Method)
Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (Effective Carbon Number)

SIGNIFICANCE AND USE
5.1 This test method is suitable for setting specifications on the materials referenced in Table 1 and for use as an internal quality control tool where cyclohexane is produced or is used in a manufacturing process. It may also be used in development or research work involving cyclohexane.  
5.2 This test method is useful in determining the purity of cyclohexane with normal impurities present. If extremely high boiling or unusual impurities are present in the cyclohexane, this test method would not necessarily detect them and the purity calculation would be erroneous.
SCOPE
1.1 This test method covers the determination of the purity of cyclohexane by gas chromatography.  
1.2 This test method has been found applicable to the measurement of impurities such as those found in Table 1, which are impurities that may be found in cyclohexane. The impurities can be analyzed over a range with an upper limit of 400 mg/kg by this method, but may be applicable to a wider range. The limit of detection (LOD) is 0.7 mg/kg and the limit of quantitation (LOQ) is 2.3 mg/kg.
Note 1: The LOD and LOQ were calculated from the ILS data for benzene.  
1.3 The following applies for the purposes of determining the conformance of the test results using this test method to applicable specifications: results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2426-23(Test Method)
Standard Test Method for Butadiene Dimer and Styrene in Butadiene Concentrates by Gas Chromatography

SIGNIFICANCE AND USE
4.1 Butadiene dimer and styrene may be present as impurities in commercial butadiene. This test method is suitable for use in internal quality control and in establishing product specifications.
SCOPE
1.1 This test method covers the determination of butadiene dimer (4-vinylcyclohexene-1) and styrene in butadiene concentrates, both recycle and specification grade.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For specific precautionary statements see Sections 6 and 8.  
1.3.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D5799-23(Test Method)
Standard Test Method for Determination of Peroxides in Butadiene

SIGNIFICANCE AND USE
4.1 Due to the inherent danger of peroxides in butadiene, specification limits are usually set for their presence. This test method will provide values that can be used to determine the peroxide content of a sample of commercial butadiene.  
4.2 Butadiene polyperoxide is a very dangerous product of the reaction between butadiene and oxygen that can occur. The peroxide has been reported to be the cause of some violent explosions in vessels that are used to store butadiene.
SCOPE
1.1 This test method covers the determination of peroxides in butadiene.  
1.2 This test method covers the concentrations range of 1 mg/kg to 10 mg/kg as available oxygen.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2712-23(Test Method)
Standard Test Method for Determination of Hydrocarbon Impurities in High Purity Propylene by Gas Chromatography

SIGNIFICANCE AND USE
5.1 High-purity propylene is required as a feedstock for various manufacturing processes, and the presence of trace amounts of certain hydrocarbon impurities may have adverse effects on yield or catalyst life. This test method is suitable for use as a benchmark in setting commercial specifications, for use as an internal quality control tool, and for use in development or research work.
SCOPE
1.1 This test method is used for the determination of hydrocarbon impurities in propylene (propene) material of 97 % by mass or greater purity (concentrates). These impurities are determined in the concentration range of 0.35 mg/kg to 8575 mg/kg and includes the following components: methane, ethane, ethylene, propane, acetylene, isobutane, propadiene, normal butane, trans-2-butene, butene-1, isobutylene, cis-2-butene, isopentane, methylacetylene, normal pentane, and 1,3-butadiene.
Note 1: Optionally, the analysis may include the determination of pentenes/hexanes and heavier components, see 6.3.  
1.2 This test method does not determine non-hydrocarbon impurities, and additional tests may be necessary to fully characterize the propylene sample. However, for the purposes of this test, the purity of propylene is determined as the difference between the total of the determined analytes and 100 % (by difference).  
1.3 When this test method is being used for the determination of trace level impurities in high-purity propylene, the use of this test method for the analysis of propylene samples at lower purities is not recommended due to the potential for cross contamination between samples.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities. The eLearning training course “Liquefied Petroleum Gases Sampling Safety” is available on the ASTM.org website.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2593-23(Test Method)
Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography

SIGNIFICANCE AND USE
4.1 The trace hydrocarbon compounds listed can have an effect in the commercial use of butadiene. This test method is suitable for use in process quality control and in setting specifications.
SCOPE
1.1 This test method covers the determination of butadiene-1,3 purity and impurities such as propane, propylene, isobutane, n-butane, butene-1, isobutylene, propadiene, trans-butene-2, cis-butene-2, butadiene-1,2, pentadiene-1,4, and, methyl, dimethyl, ethyl, and vinyl acetylene in polymerization grade butadiene by gas chromatography. Impurities including butadiene dimer, carbonyls, inhibitor, and residue are measured by appropriate ASTM procedures and the results used to normalize the component distribution obtained by chromatography.  
Note 1: Other impurities present in commercial butadiene must be calibrated and analyzed. Other impurities were not tested in the cooperative work on this test method.
Note 2: This test method can be used to check for pentadiene-1,4 and other C5s instead of Test Method D1088.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For specific warning statements, see 6.1 and 9.3.  
1.3.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D6805-02(2023)(Practice)
Standard Practice for Infrared (IR) Procedure for Determination of Aromatic/ Aliphatic Ratio of Bituminous Emulsions

SIGNIFICANCE AND USE
5.1 The results of this practice may be used to distinguish tar-based emulsion from an asphalt-based emulsion for specification compliance purposes.
SCOPE
1.1 This practice uses infrared analytical techniques to qualitatively determine in the laboratory a ratio of aromatic absorbance to aliphatic absorbance. This practice may be used to determine if the bitumen in the emulsion is predominantly aromatic or aliphatic in nature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off