ASTM A625/A625M-08
(Specification)Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
Standard Specification for Tin Mill Products, Black Plate, Single-Reduced
ABSTRACT
This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications. The black plates shall be produced with ground roll and shot-blasted roll finishes and shall be furnished oiled or dry.
SCOPE
1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.
1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed edge.
1.3 This specification is applicable to orders in either inch-pound units (as A 625), which is supplied in thicknesses from 135-lb base weight (0.0149 in.) and lighter, or SI units (as A 625M), which is supplied in thicknesses from 0.378 mm and lighter.
1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A625/A625M −08
StandardSpecification for
1
Tin Mill Products, Black Plate, Single-Reduced
This standard is issued under the fixed designationA625/A625M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 3.1.1 Name of product (single-reduced black plate).
3.1.2 Surface appearance and finish (Section 4).
1.1 This specification covers single-reduced black plate
3.1.2.1 Dry.
produced from low carbon, cold-reduced steel, furnished in
3.1.2.2 Oiled (type of oil; mineral or suitable for lithograph-
coils and cut sizes, for use in the manufacture of containers,
ing) (Section 5).
closures, signs, toys and other products, as well as for plating
3.1.2.3 Chemically treated and oiled (see Specification
applications.
A623 or Specification A623M).
1.2 It may be supplied dry or oiled and with or without
3.1.3 Thickness (see Specification A623 or Specification
surface treatment. This product is normally supplied with a
A623M).
trimmed edge.
3.1.4 Width.
1.3 This specification is applicable to orders in either 3.1.5 Length, for cut sizes only.
inch-pound units (as A625), which is supplied in thicknesses 3.1.6 Rolling direction must be specified by underlining the
from 135-lb base weight (0.0149 in.) and lighter, or SI units (as
steel (rolling width) for cut sizes.
A625M), which is supplied in thicknesses from 0.378 mm and 3.1.7 Steel type (see Specification A623 or Specification
lighter.
A623M).
3.1.8 Mechanical designation requirements (see Specifica-
1.4 The values stated in either inch-pound or SI units are to
tion A623 or Specification A623M).
be regarded as standard.Within the text, the SI units are shown
3.1.9 Intended application.
in brackets. The values stated in each system are not exact
3.1.10 Quantity, in base boxes [SITAs] (see Note 5).
equivalents; therefore, each system must be used indepen-
3.1.11 On coils, specify minimum of range or acceptable
dently of the other. Combining values from the two systems
inside diameters. The standard inside diameter is approxi-
may result in nonconformance with this specification.
mately 16 in. if ordered to Specification A625 [410 mm if
2. Referenced Documents ordered to Specification A625M]. Coils should be specified to
2 a maximum coil weight if ordered to Specification A625 [mass
2.1 ASTM Standards:
if ordered to Specification A625M] or maximum outside
A623 Specification for Tin Mill Products, General Require-
diameter, or both.
ments
3.1.12 Packaging.
A623M Specification for Tin Mill Products, General Re-
3.1.13 ASTM specification designation and year of issue.
quirements [Metric]
3.1.14 Special requirements, where applicable.
3. Ordering Information
NOTE1—Atypicalorderingdescriptionisasfollows:1000BaseBoxes,
Single-Reduced Black Plate, oiled, 80 lb base weight, 30 in. by coil, MR,
3.1 Orders for product under this specification shall include
T5CA for lithographed can bodies to ASTM A625/A625M - XX. [600
the following information, as required and applicable, to
SITAs,Single-ReducedBlackPlate,oiled,0.25mm,810mmbycoil,MR,
adequately describe the desired materials.
T5CA for lithographed can bodies to Specification A625/A625M.
NOTE 2—A typical ordering description for cut sizes is as follows: 500
BaseBoxes,SingleReducedBlackPlate,oiled,80lbbaseweightMR,T-2
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3 7
BA, 7C, 30 ⁄4 in. by 30 ⁄16 in., for lithographed can bodies in accordance
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
with Specification A625/A625M - XX. [100 SITAS, Single Reduced
A01.20 on Tin Mill Products.
Black Plate, oiled, MR, T-2 BA, 7C, 0.28 mm thickness, 781 by 773 mm,
Current edition approved Oct. 1, 2008. Published October 2008. Originally
for lithographed can bodies in accordance with Specification A625M/
approved in 1968. Last previous edition approved in 2003 as A625/A625M – 03.
A 625M - XX.]
DOI: 10.1520/A0625_A0625M-08.
2
NOTE 3—The production of coils does not afford the same opportunity
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
for inspection, grading, and sorting as does the production of cut sizes.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on Accordingly, appropriate processing and quality control procedures are
the ASTM website. required by the purchaser to obtain optimum utilization of the material.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A 625/A 625M–03 Designation: A 625/A 625M – 08
Standard Specification for
1
Tin Mill Products, Black Plate, Single-Reduced
This standard is issued under the fixed designationA625/A625M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and
cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.
1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed
edge.
1.3 This specification is applicable to orders in either inch-pound units (as A 625), which is supplied in thicknesses from
128-lb135-lb base weight (0.0141(0.0149 in.) and lighter, or SI units (as A 625M), which is supplied in thicknesses from
0.3580.378 mm and lighter.
1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown
in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the
other. Combining values from the two systems may result in nonconformance with this specification.
2. Referenced Documents
2
2.1 ASTM Standards:
A 623 Specification for Tin Mill Products, General Requirements
A 623M Specification for Tin Mill Products, General Requirements [Metric]
3. Ordering Information
3.1 Orders for product under this specification shall include the following information, as required and applicable, to adequately
describe the desired materials.
3.1.1 Name of product (single-reduced black plate).
3.1.2 Surface appearance and finish (Section 4).
3.1.2.1 Dry.
3.1.2.2 Oiled (type of oil; mineral or suitable for lithographing) (Section 5).
3.1.2.3 Chemically treated and oiled (see Specification A 623 or Specification A 623M).
3.1.3 Thickness (see Specification A 623 or Specification A 623M).
3.1.4 Width.
3.1.5 Length, for cut sizes only.
3.1.6 Rolling direction must be specified by underlining the steel (rolling width) for cut sizes.
3.1.7 Steel type (see Specification A 623 or Specification A 623M).
3.1.8 Mechanical designation requirements (see Specification A 623 or Specification A 623M).
3.1.9 Intended application.
3.1.10 Quantity, in base boxes [SITAs] (see Note 5).
3.1.11 On coils, specify minimum of range or acceptable inside diameters. The standard inside diameter is approximately 16
in. if ordered to Specification A 625 [410 mm if ordered to Specification A 625M]. Coils should be specified to a maximum coil
weight if ordered to Specification A 625 [mass if ordered to Specification A 625M] or maximum outside diameter, or both.
3.1.12 Packaging.
3.1.13 ASTM specification designation and year of issue.
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.20
on Tin Mill Products.
Current edition approved Sept. 10, 2003. Published November 2003. Originally approved in 1968. Last previous edition approved in 1998 as A625/A625M–98.
Current edition approved Oct. 1, 2008. Published October 2008. Originally approved in 1968. Last previous edition approved in 2003 as A 625/A 625M – 03.
2
Annual Book of ASTM Standards, Vol 01.06.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A 625/A 625M – 08
3.1.14 Special requirements, where applicable.
NOTE 1—A typical ordering description is as follows: 1000 Base Boxes, Single-Reduced Black Plate, oiled, 80 lb base weight, 30 in. by coil, MR,
T5CAfor lithographed can bodies toASTMA 625/A 625M - XX. [600 SITAs, Single-Reduced Black Plate, oiled, 0.25 mm, 810 mm by coil, MR,T5CA
for lithographed can bodies to Specification A 625/A 625M.
NOTE 2—A typical ordering description for cut sizes is as foll
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.