ASTM F2648/F2648M-22

Standard Specification for 50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

ABSTRACT
This specification covers the general requirements and corresponding test methods for non-pressure (gravity flow) polyethylene (PE) pipes and fittings having interior liner with annular corrugated exterior wall profile, and whose inside diameters are 2 to 60 in. [50 to 1500 mm]. These pipes and fittings are suitable for underground use in subsurface and land drainage systems, which do not operate under surcharge pressure heads. Material requirements are specified for pipe and blow molded fittings, rotationally molded fittings and couplings, injection molded fittings and couplings, and rework materials. The resulting products shall be tested as appropriate, and shall conform to specified requirements for workmanship, dimension (inside diameter, length, minimum inner liner thickness, and perforations), stiffness, flattening resistance, impact resistance, and slow crack growth resistance of PE plastics without pigment.
SCOPE
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 50 mm to 1500 mm [2 in. to 60 in.].  
1.2 The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.
Note 1: Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on diameter limitations within the respective standards.
Note 2: Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer applications.  
1.3 This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).  
1.4 This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.  
1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 28-Feb-2022
• ICS: 65.060.35 - Irrigation and drainage equipment
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.65 - Land Drainage

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2648/F2648M − 22
Standard Specification for
50 mm to 1500 mm [2 in. to 60 in.] Annular Corrugated
Profile Wall Polyethylene (PE) Pipe and Fittings for Land
1
Drainage Applications
This standard is issued under the fixed designation F2648/F2648M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.7 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This specification covers requirements and test methods
ization established in the Decision on Principles for the
for annular corrugated profile wall polyethylene pipe and
Development of International Standards, Guides and Recom-
fittings with an interior liner. The inside diameters covered are
mendations issued by the World Trade Organization Technical
50 mm to 1500 mm [2 in. to 60 in.].
Barriers to Trade (TBT) Committee.
1.2 The requirements of this specification are intended to
provide non-pressure (gravity flow) pipe and fittings for
2. Referenced Documents
underground use for subsurface and land drainage systems, 2
2.1 ASTM Standards:
which do not operate under surcharge pressure heads.
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plas-
NOTE 1—Pipe and fittings produced in accordance with this specifica-
tion are be installed in compliance with Practice D2321 or Practice F449
tics
based on diameter limitations within the respective standards.
D2122 Test Method for Determining Dimensions of Ther-
NOTE 2—Subsurface and land drainage systems pertain principally to
moplastic Pipe and Fittings
non-municipal or private facilities for water table control, storm drainage
D2321 Practice for Underground Installation of Thermoplas-
and agricultural drainage applications. The products supplied under this
specification are not intended for any sanitary sewer or municipal storm tic Pipe for Sewers and Other Gravity-Flow Applications
sewer applications.
D2412 Test Method for Determination of External Loading
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.3 This specification covers pipe and fittings with an
D2444 Practice for Determination of the Impact Resistance
interior liner using an annular exterior corrugated profile (Fig.
of Thermoplastic Pipe and Fittings by Means of a Tup
1).
(Falling Weight)
1.4 This specification permits the use of recycled materials
D3350 Specification for Polyethylene Plastics Pipe and Fit-
for pipe in accordance with the requirements in Section 5.
tings Materials
1.5 Units—The values stated in either SI units or inch-
D4218 Test Method for Determination of Carbon Black
pound units are to be regarded separately as standard. The
Content in Polyethylene Compounds by the Muffle-
values stated in each system are not necessarily exact equiva-
Furnace Technique
lents; therefore, to ensure conformance with the standard, each
D5630 Test Method for Ash Content in Plastics (Withdrawn
3
system shall be used independently of the other, and values
2022)
from the two systems shall not be combined.
D7399 Test Method for Determination of the Amount of
Polypropylene in Polypropylene/Low Density Polyethyl-
1.6 This standard does not purport to address all of the
ene Mixtures Using Infrared Spectrophotometry
safety concerns, if any, associated with its use. It is the
F412 Terminology Relating to Plastic Piping Systems
responsibility of the user of this standard to establish appro-
F449 Practice for Subsurface Installation of Corrugated
priate safety, health, and environmental practices and deter-
Polyethylene Pipe for Agricultural Drainage or Water
mine the applicability of regulatory limitations prior to use.
Table Control
1 2
This specification is under the jurisdiction of ASTM Committee F17 on Plastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Drainage. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved March 1, 2022. Published March 2022. Originally the ASTM website.
3
approved in 2007. Last previous edition approved in 2020 as F2648/F2648M – 20. The last approved version of this historical standard is referenced on
DOI: 10.1520/F2648_F2648M-22. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

----------------
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2648/F2648M − 20 F2648/F2648M − 22
Standard Specification for
2 to 60 inch [50 to 1500 mm]50 mm to 1500 mm [2 in. to 60
in.] Annular Corrugated Profile Wall Polyethylene (PE) Pipe
1
and Fittings for Land Drainage Applications
This standard is issued under the fixed designation F2648/F2648M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with
an interior liner. The inside diameters covered are 2 to 60 in. [50 to 1500 mm].50 mm to 1500 mm [2 in. to 60 in.].
1.2 The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings for underground
use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.
NOTE 1—Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on
diameter limitations within the respective standards.
NOTE 2—Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and
agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer
applications.
1.3 This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).
1.4 This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.
1.5 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in
each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used
independently of the other, and values from the two systems shall not be combined.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land Drainage.
Current edition approved Feb. 1, 2020March 1, 2022. Published March 2020March 2022. Originally approved in 2007. Last previous edition approved in 20172020 as
F2648/F2648M – 17.20. DOI: 10.1520/F2648_F2648M-20.10.1520/F2648_F2648M-22.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2648/F2648M − 22
FIG. 1 Annular Corrugated Profile Wall Polyethylene Pipe with Interior Liner
TABLE 1 Pipe Stiffness and Pipe Dimensions
A
Pipe Inside Diameter Minimum Pipe Stiffness Minimum
at 5% Deflection Inner Liner
Thickness
inch [mm] lb/in/in [kPa] Inch [mm]
2 [50] 50 [345] 0.020 [0.5]
3 [75] 50 [345] 0.020 [0.5]
4 [100] 50 [345] 0.020 [0.5]
6 [150] 50 [345] 0.020 [0.5]
8 [200] 50 [345] 0.024 [0.6]
10 [250] 50 [345] 0.024 [0.6]
12 [300] 50 [345] 0.035 [0.9]
15 [375] 42 [290] 0.040 [1.0]
18 [450] 40 [275] 0.051 [1.3]
21 [525] 38 [260] 0.060 [1.5]
24 [600] 34 [235] 0.060 [1.5]
27 [675] 30 [205] 0.060 [1.5]
30 [750] 28 [195] 0.060 [1.5]
36 [900] 22 [150] 0.067 [1.7]
42 [1050] 20 [140] 0.071 [1.8]
48 [1200] 18 [125] 0.071 [1.8]
54 [1350] 16 [110] 0.079 [2.0]
60 [1500] 14 [97] 0.079 [2.0]
A
TABLE 1 Pipe Dimensions and Stiffness
NID Minimum Inside Diameter Minimum Liner Thickness Minimum Pipe Stiffness Minimum
at 5% Deflection SN Class
Metric Series US mm in. mm in. kPa lb/in./in. [SN]
Customary
Series
50 2 48 1.90 0.5 0.020 345 50 8
75 3 75 2.97 0.5 0.020 345 50 8
100 4 95 3.74 0.5 0.020 345
...