ASTM A888-05
(Specification)Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications
SCOPE
1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.
1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.
1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification.
1.4 The values stated in inch-pound units shall be regarded as the standard. The values given in parentheses shall be for information only. Metric conversions in Figs. 1 and 2 are to two decimal places; all other metric conversions are rounded to the nearest whole number.
1.5 The committee with jurisdiction over this standard is aware of another comparable standard published by the Cast Iron Soil Pipe Institute, CISPI 301.
Note 1—The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A 888 – 05
Standard Specification for
Hubless Cast Iron Soil Pipe and Fittings for Sanitary and
1
Storm Drain, Waste, and Vent Piping Applications
This standard is issued under the fixed designation A 888; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
Short Sweep Fig. 12
Long Sweep Fig. 13
1.1 This specification covers hubless cast iron soil pipe and
Long Sweep, Reducing Fig. 14
fittings for use in gravity flow applications. It establishes
Fifth Bend Fig. 15
Sixth Bend Fig. 16
standards covering material, manufacture, mechanical and
Eighth Bend Fig. 17
chemical properties, dimensions, coating, test methods, inspec-
Eighth Bend Long Fig. 18
tion, certification, and product marking for hubless cast iron Sixteenth Bend Fig. 19
Sanitary Tee Fig. 20
soil pipe and fittings. These pipe and fittings are intended for
Sanitary Tee With Side Opening Fig. 21
non-pressure applications, as the selection of the proper size
Sanitary Tee With 2 in. Side Opening R or L/R and L Fig. 22
for sanitary drain, waste, vent, and storm drain systems allows Sanitary Tee, New Orleans Special With Side Opening Fig. 23
Sanitary Tee With 45° Side Openings and New Orleans Fig. 24
free air space for gravity drainage.
Sanitary Special Tee Tapped Fig. 25
1.2 The EDP/ASA numbers indicated in this section repre-
Sanitary Tapped Tee, Horizontal Twin Fig. 26
sent a Uniform Industry Code adopted by theAmerican Supply
Sanitary Tapped Tee, Double Vertical Fig. 27
Y Branch Fig. 28
Association (ASA). A group designation prefix, 022, is as-
Y Branch, Double Fig. 29
signed to hubless products, followed by the four-digit identi-
Y Branch, Upright Fig. 30
fication assigned to individual items and a check digit. This Upright Y Wide Center Florida Special Fig. 31
1
Y Branch, Combination ⁄8 Bend Fig. 32
system has been instituted to facilitate EDP control through
1
Y Branch, Combination ⁄8 Bend Double Fig. 33
distribution channels, and is to be used universally in ordering
Sanitary Cross Fig. 34
and specifying product items. Those items with no EDP Sanitary Cross With Side Opening Fig. 35
Sanitary Cross, New Orleans, With Side Openings Fig. 36
numbers are either new, special, or transitory and will be
Sanitary Cross, New Orleans, With 45° Special and Fig. 37
assigned numbers on subsequent prints of this specification.
Regular Side Openings
Sanitary Cross, Tapped Fig. 38
1.3 This specification covers pipe and fittings of the follow-
Test Tee Fig. 39
ingpatternsandappliestoanyotherpatternsthatconformwith
Tapped, Extension Piece Fig. 40
2
the applicable requirements given in this specification.
Increaser-Reducer Fig. 41
1.3.1 Lengths: Increaser-Reducer, Short Fig. 42
Tapped Adapter Fig. 43
Figures
Blind Plug Fig. 44
EDP/ASA Identification Numbers Fig. 1
Iron Body Cleanout-Tapped Fig. 45
for Hubless Pipe
P Trap Fig. 46
10 ft (3.0 m) in sizes and 5 ft. (1.5 m) Fig. 1, Fig. 2
P Trap, Long Fig. 47
1
1 ⁄2,2,3,4,5,6,8,
P Trap, Deep Seal Fig. 48
10, 12, and 15 in.
P Trap, With Primer Fig. 49
Method of Specifying Fittings Fig. 3
P Trap, With Tapped Inlet Fig. 50
Hub Adapter Fig. 51
1.3.2 Fittings:
Tapped Inlet, Double Fig. 52
Quarter Bend Fig. 5 1
Modified Combination Wye and ⁄8 Bend, Double Fig. 53
Quarter Bend, Reducing Fig. 6 1
Modified Combination Wye and ⁄8 Bend, Double, Ex- Fig. 54
Quarter Bend, With Side Opening Fig. 7
tended
Quarter Bend, With Heel Opening Fig. 8
Regular or Extended Left or Right Regular or Extended Fig. 55
Quarter Bend, Tapped Fig. 9
Double
Quarter Bend, Double Fig. 10
Regular or Extended Left or Right Regular or Extended Fig. 56
Quarter Bend, Long Fig. 11
Double
Two-Way Cleanout Fig. 57
Twin Cleanout Fig. 58
Closet Bend, Regular and Reducing Fig. 59
1
This specification is under the jurisdiction of ASTM Committee A04 on Iron
Closet Flange Riser Fig. 60
CastingsandisunderthedirectresponsibilityofSubcommitteeA04.12onPipesand
Tapping Bosses Fig. 61
Tubes.
Closet Flanges Fig. 62
Current edition approved June 1, 2005. Published June 2005. Originally
Double Sweep Sanitary Tee (Extended) Fig. 63
approved in 1990. Last previous edition approved in 2004 as A 888 – 04a.
2
Reprinted with permission from Cast Iron Soil Pipe Institute.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A888–05
ASA—American Supply Association
Running Trap with Double Vents Fig. 64
P Trap with Tapped or Hubless Side Inlet Fig. 65
ASSY—assembly
Vented Tub Wye Extended, Double Fig. 66
BD—bend
Vented Tub Wye Extended Offset, Left or Righ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.