ASTM A650/A650M-18
(Specification)Standard Specification for Tin Mill Products, Black Plate, Double Reduced
Standard Specification for Tin Mill Products, Black Plate, Double Reduced
ABSTRACT
This specification covers doubled-reduced black plate tin mill products produced from low-carbon cold-reduced steel, furnished in coils and cut sizes, for use predominantly in the manufacture of containers. The product, which is normally supplied with trimmed edges, may be specified "as rolled," without the removal of the rolling solution, and with no additional surface or oiling treatment, or "cleaned" with the rolling solution removed, with or without surface treatment and oiling. The rolling direction must be specified on cut lengths and will be indicated by underlining the slit (rolling width) dimension. Surfaces may polished in either the ground roll finish (base metal finish), or smooth finish with grit lines (7C finish).
SCOPE
1.1 This specification covers double-reduced black plate, produced from low-carbon cold-reduced steel, furnished in coils and cut sizes, for use predominantly in the manufacture of containers. The product may be specified “as rolled,” without the removal of the rolling solution, and with no additional surface or oiling treatment. It may also be specified “cleaned” with the rolling solution removed, with or without surface treatment and oiling. This product is normally supplied with trimmed edges.
1.2 This specification is applicable to orders in either inch-pound units (as A650) which is supplied in thicknesses 0.0050 in. to 0.0113 in. or SI units [as A650M] which is supplied in thicknesses from 0.127 to 0.287 mm.
1.3 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A650/A650M −18
Standard Specification for
1
Tin Mill Products, Black Plate, Double Reduced
This standard is issued under the fixed designationA650/A650M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Ordering Information
1.1 This specification covers double-reduced black plate, 3.1 Orders for material under this specification shall include
produced from low-carbon cold-reduced steel, furnished in the following information, as required and applicable, to
coilsandcutsizes,forusepredominantlyinthemanufactureof
adequately describe the desired materials.
containers. The product may be specified “as rolled,” without
3.1.1 Name of material (double-reduced black plate),
the removal of the rolling solution, and with no additional
3.1.1.1 As rolled, with the rolling solution not removed,
surface or oiling treatment. It may also be specified “cleaned”
3.1.1.2 Cleaned, with the rolling solution removed, not
with the rolling solution removed, with or without surface
reoiled,
treatment and oiling. This product is normally supplied with
3.1.1.3 Cleaned and oiled, with the rolling solution removed
trimmed edges.
and reoiled,
3.1.1.4 Cleaned, chemically treated and oiled, with the
1.2 This specification is applicable to orders in either
rolling solution removed, chemically treated and reoiled.
inch-pound units (as A650) which is supplied in thicknesses
3.1.2 Thickness (see Specification A623 [Specification
0.0050 in. to 0.0113 in. or SI units [as A650M] which is
supplied in thicknesses from 0.127 to 0.287 mm. A623M]),
3.1.3 Width,
1.3 The values stated in either inch-pound or SI units are to
3.1.4 Length, for cut sizes only,
be regarded as standard.Within the text, the SI units are shown
3.1.5 Rolling direction must be specified by underlining the
in brackets. The values stated in each system are not exact
slit (rolling width) for cut sizes (see 4.1),
equivalents; therefore, each system must be used indepen-
3.1.6 Steel type (see Specification A623 [Specification
dently of the other. Combining values from the two systems
A623M]),
may result in nonconformance with this specification.
3.1.7 Mechanical designation requirements (see Specifica-
1.4 This international standard was developed in accor-
tion A623 [Specification A623M]),
dance with internationally recognized principles on standard-
3.1.8 Intended application,
ization established in the Decision on Principles for the
3.1.9 Quantity, in base boxes [SITAs] (see Note 5),
Development of International Standards, Guides and Recom-
3.1.10 On coils, specify minimum or range of acceptable
mendations issued by the World Trade Organization Technical
inside diameters. The standard inside diameter is approxi-
Barriers to Trade (TBT) Committee.
mately 16 in. if ordered to Specification A650 [410 mm if
ordered to Specification A650M]. Coils should be specified to
2. Referenced Documents
a maximum coil weight if ordered to SpecificationA650 [mass
2
2.1 ASTM Standards:
if ordered to Specification A650M] or maximum outside
A623 Specification for Tin Mill Products, General Require-
diameter,
ments
3.1.11 Packaging,
A623M Specification for Tin Mill Products, General Re-
3.1.12 Special requirements where applicable, and
quirements [Metric]
3.1.13 ASTM specification number and year of issue
(A650/A650M – 88).
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
NOTE 1—A typical ordering description is as follows: 1200 base boxes
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
double-reduced black plate, cleaned and oiled, 60-lb base weight, 33
A01.20 on Tin Mill Products.
1
⁄16 in. by coil, MR, DR8 CA, for 401 by 411 can bodies to ASTM
Current edition approved Nov. 1, 2018. Published December 2018. Originally
Specification A650/A650M - XX. [250 SITAs, double-reduced black
approved in 1971. Last previous edition approved in 2013 as A650/A650M – 13.
plate, cleaned and oiled, 0.17 mm thickness, 840 mm by coil, MR, DR8
DOI: 10.1520/A0650_A0650M-18.
2 CA, for 99 mm can bodies to ASTM Specification A650/A650M.]
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
NOTE 2—A typical ordering description for cut sizes is as follows: 500
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on base boxes, double-reduced black plate, cleaned and oiled, 60-lb bas
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A650/A650M − 13 A650/A650M − 18
Standard Specification for
1
Tin Mill Products, Black Plate, Double Reduced
This standard is issued under the fixed designation A650/A650M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers double-reduced black plate, produced from low-carbon cold-reduced steel, furnished in coils and
cut sizes, for use predominantly in the manufacture of containers. The product may be specified “as rolled,” without the removal
of the rolling solution, and with no additional surface or oiling treatment. It may also be specified “cleaned” with the rolling
solution removed, with or without surface treatment and oiling. This product is normally supplied with trimmed edges.
1.2 This specification is applicable to orders in either inch-pound units (as A650) which is supplied in thicknesses 0.0050 in.
to 0.0113 in. or SI units [as A650M] which is supplied in thicknesses from 0.127 to 0.287 mm.
1.3 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown
in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the
other. Combining values from the two systems may result in nonconformance with this specification.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A623 Specification for Tin Mill Products, General Requirements
A623M Specification for Tin Mill Products, General Requirements [Metric]
3. Ordering Information
3.1 Orders for material under this specification shall include the following information, as required and applicable, to adequately
describe the desired materials.
3.1.1 Name of material (double-reduced black plate),
3.1.1.1 As rolled, with the rolling solution not removed,
3.1.1.2 Cleaned, with the rolling solution removed, not reoiled,
3.1.1.3 Cleaned and oiled, with the rolling solution removed and reoiled,
3.1.1.4 Cleaned, chemically treated and oiled, with the rolling solution removed, chemically treated and reoiled.
3.1.2 Thickness (see Specification A623 [Specification A623M]),
3.1.3 Width,
3.1.4 Length, for cut sizes only,
3.1.5 Rolling direction must be specified by underlining the slit (rolling width) for cut sizes (see 4.1),
3.1.6 Steel type (see Specification A623 [Specification A623M]),
3.1.7 Mechanical designation requirements (see Specification A623 [Specification A623M]),
3.1.8 Intended application,
3.1.9 Quantity, in base boxes [SITAs] (see Note 5),
3.1.10 On coils, specify minimum or range of acceptable inside diameters. The standard inside diameter is approximately 16
in. if ordered to Specification A650 [410 mm if ordered to Specification A650M]. Coils should be specified to a maximum coil
weight if ordered to Specification A650 [mass if ordered to Specification A650M] or maximum outside diameter,
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee A01.20
on Tin Mill Products.
Current edition approved Oct. 1, 2013Nov. 1, 2018. Published October 2013December 2018. Originally approved in 1971. Last previous edition approved in 20082013
as A650/A650M – 03A650/A650M(2008). – 13. DOI: 10.1520/A0650_A0650M-13. 10.1520/A0650_A0650M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A650/A650M − 18
3.1.11 Packaging,
3.1.12 Special requirements where applicable, and
3.1.13 ASTM specification number and year of issue (A650/A650M – 88).
1
NOTE 1—A typical ordering descript
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A650/A650M − 18
Standard Specification for
1
Tin Mill Products, Black Plate, Double Reduced
This standard is issued under the fixed designation A650/A650M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Ordering Information
1.1 This specification covers double-reduced black plate,
3.1 Orders for material under this specification shall include
produced from low-carbon cold-reduced steel, furnished in
the following information, as required and applicable, to
coils and cut sizes, for use predominantly in the manufacture of adequately describe the desired materials.
containers. The product may be specified “as rolled,” without
3.1.1 Name of material (double-reduced black plate),
the removal of the rolling solution, and with no additional
3.1.1.1 As rolled, with the rolling solution not removed,
surface or oiling treatment. It may also be specified “cleaned”
3.1.1.2 Cleaned, with the rolling solution removed, not
with the rolling solution removed, with or without surface
reoiled,
treatment and oiling. This product is normally supplied with
3.1.1.3 Cleaned and oiled, with the rolling solution removed
trimmed edges.
and reoiled,
3.1.1.4 Cleaned, chemically treated and oiled, with the
1.2 This specification is applicable to orders in either
rolling solution removed, chemically treated and reoiled.
inch-pound units (as A650) which is supplied in thicknesses
0.0050 in. to 0.0113 in. or SI units [as A650M] which is 3.1.2 Thickness (see Specification A623 [Specification
A623M]),
supplied in thicknesses from 0.127 to 0.287 mm.
3.1.3 Width,
1.3 The values stated in either inch-pound or SI units are to
3.1.4 Length, for cut sizes only,
be regarded as standard. Within the text, the SI units are shown
3.1.5 Rolling direction must be specified by underlining the
in brackets. The values stated in each system are not exact
slit (rolling width) for cut sizes (see 4.1),
equivalents; therefore, each system must be used indepen-
3.1.6 Steel type (see Specification A623 [Specification
dently of the other. Combining values from the two systems
A623M]),
may result in nonconformance with this specification.
3.1.7 Mechanical designation requirements (see Specifica-
1.4 This international standard was developed in accor-
tion A623 [Specification A623M]),
dance with internationally recognized principles on standard-
3.1.8 Intended application,
ization established in the Decision on Principles for the
3.1.9 Quantity, in base boxes [SITAs] (see Note 5),
Development of International Standards, Guides and Recom-
3.1.10 On coils, specify minimum or range of acceptable
mendations issued by the World Trade Organization Technical
inside diameters. The standard inside diameter is approxi-
Barriers to Trade (TBT) Committee.
mately 16 in. if ordered to Specification A650 [410 mm if
ordered to Specification A650M]. Coils should be specified to
2. Referenced Documents
a maximum coil weight if ordered to Specification A650 [mass
2
2.1 ASTM Standards:
if ordered to Specification A650M] or maximum outside
A623 Specification for Tin Mill Products, General Require-
diameter,
ments
3.1.11 Packaging,
A623M Specification for Tin Mill Products, General Re-
3.1.12 Special requirements where applicable, and
quirements [Metric]
3.1.13 ASTM specification number and year of issue
(A650/A650M – 88).
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
NOTE 1—A typical ordering description is as follows: 1200 base boxes
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee
double-reduced black plate, cleaned and oiled, 60-lb base weight, 33
A01.20 on Tin Mill Products.
1
⁄16 in. by coil, MR, DR8 CA, for 401 by 411 can bodies to ASTM
Current edition approved Nov. 1, 2018. Published December 2018. Originally
Specification A650/A650M - XX. [250 SITAs, double-reduced black
approved in 1971. Last previous edition approved in 2013 as A650/A650M – 13.
plate, cleaned and oiled, 0.17 mm thickness, 840 mm by coil, MR, DR8
DOI: 10.1520/A0650_A0650M-18.
2
CA, for 99 mm can bodies to ASTM Specification A650/A650M.]
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
NOTE 2—A typical ordering description for cut sizes is as follows: 500
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
base boxes, double-reduced black plate, cleaned and oiled, 60-lb base
Standards volume information, refer to the standard’s Document Summary page on
1
the ASTM website. weight MR, DR8 CA, 7C, 28 by 33 ⁄16 in., for 401 by 411 can bodies in
*A Summary of Changes sec
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.