ASTM B208-14(2021)

Standard Practice for Preparing Tension Test Specimens for Copper Alloy Sand, Permanent Mold, Centrifugal, and Continuous Castings

SIGNIFICANCE AND USE
4.1 The mechanical properties determined from test bars for sand, permanent mold, and centrifugal castings poured in accordance with this practice represent the properties of the metal going into castings poured from the same heat. These mechanical properties may not be the same as the properties of the corresponding castings because of the solidification effects of varying size, section, and design.  
4.2 Test bars for continuous castings are taken from the castings and therefore represent the properties of the castings.
SCOPE
1.1 This practice establishes procedures for preparing test coupons and specimens (machined and unmachined) for tension tests of copper alloys for sand, permanent mold, centrifugal and continuous castings.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 30-Jun-2021
• ICS: 77.040.10 - Mechanical testing of metals
• ICS: 77.150.30 - Copper products
• Technical Committee: B05 - Copper and Copper Alloys
• Drafting Committee: B05.05 - Castings and Ingots for Remelting

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: B208 − 14 (Reapproved 2021) Endorsed by
American Foundrymen’s Society
Standard Practice for
Preparing Tension Test Specimens for Copper Alloy Sand,
1
Permanent Mold, Centrifugal, and Continuous Castings
This standard is issued under the fixed designation B208; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* mechanical properties may not be the same as the properties of
the corresponding castings because of the solidification effects
1.1 This practice establishes procedures for preparing test
of varying size, section, and design.
coupons and specimens (machined and unmachined) for ten-
sion tests of copper alloys for sand, permanent mold, centrifu- 4.2 Test bars for continuous castings are taken from the
gal and continuous castings. castings and therefore represent the properties of the castings.
1.2 The values stated in inch-pound units are to be regarded
5. Test Coupons
as standard. The values given in parentheses are mathematical
5.1 Sand Castings—The test bar coupons shall be made by
conversions to SI units that are provided for information only
the same manufacturing process as the castings they represent
and are not considered standard.
wherever possible. If the castings are cast entirely in green
1.3 This international standard was developed in accor-
sand, partial cores shall be permitted for the test bars but in no
dance with internationally recognized principles on standard-
case shall chills be permitted. Unless otherwise agreed upon
ization established in the Decision on Principles for the
between the manufacturer and purchaser, test bars may be
Development of International Standards, Guides and Recom-
poured in cores on a production line. The use of filters in the
mendations issued by the World Trade Organization Technical
gating system is permitted.
Barriers to Trade (TBT) Committee.
5.1.1 High-Shrinkage Sand-Cast Alloys—The test specimen
coupons for copper casting alloys exhibiting high shrinkage
2. Referenced Documents
during freezing and cooling shall be cast to the form and
2
2.1 ASTM Standards:
dimensions shown in Fig. 1 (a or b) or 2 (a or b). If specimens
B846 Terminology for Copper and Copper Alloys
having threaded ends are to be used in the tension tests, the
1
length of the keel blocks in Fig. 1a may be reduced to 6 ⁄4 in.
3. Terminology
(159 mm). See Appendix X1 for SI equivalents.
3.1 Definitions of terms relating to copper alloys can be 5.1.2 Low-Shrinkage Sand-Cast Alloys—The test specimen
found in Terminology B846.
coupons for copper casting alloys exhibiting low shrinkage
during freezing and cooling shall be cast to the form and
4. Significance and Use
dimensionsshowninFig.2(AorB),Fig.3,orFig.4orasmay
be prescribed in the casting specifications.
4.1 The mechanical properties determined from test bars for
sand, permanent mold, and centrifugal castings poured in
5.2 CentrifugalCastings—Unlessotherwisespecifiedbythe
accordance with this practice represent the properties of the
purchaser, the manufacturer shall pour the test bars in the same
metal going into castings poured from the same heat. These
type of mold as the castings themselves. That is, test bars for
sand mold castings shall be poured in sand molds, and test bars
1 for chill mold castings shall be poured in chill molds.
This practice is under the jurisdiction ofASTM Committee B05 on Copper and
CopperAlloys and is the direct responsibility of Subcommittee B05.05 on Castings 5.2.1 The centrifugally cast test specimen coupons shall be
and Ingots for Remelting.
cast to the form and dimensions of Fig. 5a.
Current edition approved July 1, 2021. Published July 2021. Originally approved
5.2.2 Static test bar coupons shall be cast in open keel block
in 1946. Last previous edition approved in 2014 as B208 – 14. DOI: 10.1520/
molds as dimensioned in Fig. 5b.
B0208-14R21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.3 Continuous Castings—Test bars shall be taken from the
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
continuous cast product. Test bars may be taken before
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. mechanical straightening.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive,
...