iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E313-20

(Practice)

Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates

Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates

SIGNIFICANCE AND USE
5.1 This practice should be used only to compare specimens of the same material and same general appearance. For example, a series of specimens to be compared should have generally similar gloss, texture, and (if not opaque) thickness, and translucency.  
5.2 For yellowness measurement, this practice is limited to specimens having dominant wavelength in the range 570 to 580 nm, or Munsell hue approximately 2.5GY to 2.5Y. For whiteness measurement, this practice is limited to specimens having Munsell value greater than 8.3 (CIE Y greater than 65) and Munsell chroma no greater than 0.5 for B hues, 0.8 for Y hues, and 0.3 for all other hues (see 3.3.1).  
5.3 The combination of measurement and calculation leading to indices of yellowness or whiteness is a psychophysical process, that is, the procedures specified are designed to provide numbers correlating with visual estimates made under specified typical observing conditions. Because visual observing conditions can vary widely, users should compare calculated indices with visual estimates to ensure applicability. Some standards addressing the visual estimation of color and color difference are Practices D1535, D1729, E1360, and E1541, and Guide E1499.  
5.4 This practice does not cover the preparation of specimens, a procedure that may affect significantly the quantities measured. In general, specimens should be prepared and presented for measurement in the manner that is standard for the test being performed. Select enough specimens or specimen areas to provide an average result that is representative of each sample to be tested. See Practice E1345.
SCOPE
1.1 This practice provides numbers that correlate with visual ratings of yellowness or whiteness of white and near-white or colorless object-color specimens, viewed in daylight by an observer with normal color vision. White textiles, paints, and plastics are a few of the materials that can be described by the indices of yellowness or whiteness calculated by this practice.  
1.2 For a complete analysis of object colors, by a specified observer and under a specified illuminant, use of three parameters is required. For near-white specimens, however, it is often useful to calculate single-number scales of yellowness or whiteness. This practice provides recommended equations for such scales and discusses their derivations and uses, and limits to their applicability (see also Ref (1)2).  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Apr-2020
ICS
17.180.20 - Colours and measurement of light
Technical Committee
E12 - Color and Appearance
Drafting Committee
E12.04 - Color and Appearance Analysis
Current Stage
Ref Project

Relations

Refers
ASTM E1347-06(2020) - Standard Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
Effective Date
01-May-2020

Buy Standard

ASTM E313-20 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color CoordinatesASTM E313-20 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
PreviousNext
Standard
ASTM E313-20 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E313-20 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color CoordinatesREDLINE ASTM E313-20 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
PreviousNext
Standard
REDLINE ASTM E313-20 - Standard Practice for Calculating Yellowness and Whiteness Indices from Instrumentally Measured Color Coordinates
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: E313 − 20
Standard Practice for
Calculating Yellowness and Whiteness Indices from
1
Instrumentally Measured Color Coordinates
This standard is issued under the fixed designation E313; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
3
2.1 ASTM Standards:
1.1 This practice provides numbers that correlate with
D1535Practice for Specifying Color by the Munsell System
visual ratings of yellowness or whiteness of white and near-
D1729Practice for Visual Appraisal of Colors and Color
white or colorless object-color specimens, viewed in daylight
Differences of Diffusely-Illuminated Opaque Materials
byanobserverwithnormalcolorvision.Whitetextiles,paints,
D1925Test Method forYellowness Index of Plastics (With-
and plastics are a few of the materials that can be described by
4,5
drawn 1995)
the indices of yellowness or whiteness calculated by this
E284Terminology of Appearance
practice.
E308PracticeforComputingtheColorsofObjectsbyUsing
1.2 For a complete analysis of object colors, by a specified
the CIE System
observer and under a specified illuminant, use of three param-
E805Practice for Identification of Instrumental Methods of
etersisrequired.Fornear-whitespecimens,however,itisoften
Color or Color-Difference Measurement of Materials
useful to calculate single-number scales of yellowness or
E991Practice for Color Measurement of Fluorescent Speci-
whiteness. This practice provides recommended equations for
mens Using the One-Monochromator Method
such scales and discusses their derivations and uses, and limits
E1164PracticeforObtainingSpectrometricDataforObject-
2
to their applicability (see also Ref (1) ).
Color Evaluation
E1247Practice for Detecting Fluorescence in Object-Color
1.3 The values stated in SI units are to be regarded as
Specimens by Spectrophotometry
standard. No other units of measurement are included in this
E1331Test Method for Reflectance Factor and Color by
standard.
Spectrophotometry Using Hemispherical Geometry
1.4 This standard does not purport to address all of the
E1345Practice for Reducing the Effect of Variability of
safety concerns, if any, associated with its use. It is the
Color Measurement by Use of Multiple Measurements
responsibility of the user of this standard to establish appro-
E1347Test Method for Color and Color-Difference Mea-
priate safety, health, and environmental practices and deter-
surement by Tristimulus Colorimetry
mine the applicability of regulatory limitations prior to use.
E1348Test Method for Transmittance and Color by Spec-
1.5 This international standard was developed in accor- trophotometry Using Hemispherical Geometry
E1349Test Method for Reflectance Factor and Color by
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the Spectrophotometry Using Bidirectional (45°:0° or 0°:45°)
Geometry
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical E1360Practice for Specifying Color by Using the Optical
Society of America Uniform Color Scales System
Barriers to Trade (TBT) Committee.
E1499Guide for Selection, Evaluation, and Training of
Observers
1
This practice is under the jurisdiction of ASTM Committee E12 on Color and
3
Appearance and is the direct responsibility of Subcommittee E12.04 on Color and For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Appearance Analysis. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved May 1, 2020. Published May 2020. Originally Standards volume information, refer to the standard’s Document Summary page on
ɛ1
approved in 1967. Last previous edition approved in 2015 as E313–15 . DOI: the ASTM website.
4
10.1520/E0313-20. The last approved version of this historical standard is referenced on
2
Theboldfacenumbersinparenthesesrefertothelistofreferencesattheendof
www.astm.org.
5
this practice. Replaced by Section 6 of E313.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1

---------------------- Page: 1 ----------------------
E313 − 20
E1541Practice for Specifying and Matching Color Using 5. Significance and Use
4
the Colorcurve System (Withdrawn 2007)
5.1 Thispracticeshouldbeusedonlytocomparespecimens
of the same material and same general appearance. For
3. Terminology
exa
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: E313 − 15 E313 − 20
Standard Practice for
Calculating Yellowness and Whiteness Indices from
1
Instrumentally Measured Color Coordinates
This standard is issued under the fixed designation E313; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Section 7 was corrected editorially in June 2015.
1. Scope
1.1 This practice provides numbers that correlate with visual ratings of yellowness or whiteness of white and near-white or
colorless object-color specimens, viewed in daylight by an observer with normal color vision. White textiles, paints, and plastics
are a few of the materials that can be described by the indices of yellowness or whiteness calculated by this practice.
1.2 For a complete analysis of object colors, by a specified observer and under a specified illuminant, use of three parameters
is required. For near-white specimens, however, it is often useful to calculate single-number scales of yellowness or whiteness. This
practice provides recommended equations for such scales and discusses their derivations and uses, and limits to their applicability
2
(see also Ref (1) ).
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D1535 Practice for Specifying Color by the Munsell System
D1729 Practice for Visual Appraisal of Colors and Color Differences of Diffusely-Illuminated Opaque Materials
4,5
D1925 Test Method for Yellowness Index of Plastics (Withdrawn 1995)
E284 Terminology of Appearance
E308 Practice for Computing the Colors of Objects by Using the CIE System
E805 Practice for Identification of Instrumental Methods of Color or Color-Difference Measurement of Materials
E991 Practice for Color Measurement of Fluorescent Specimens Using the One-Monochromator Method
E1164 Practice for Obtaining Spectrometric Data for Object-Color Evaluation
E1247 Practice for Detecting Fluorescence in Object-Color Specimens by Spectrophotometry
E1331 Test Method for Reflectance Factor and Color by Spectrophotometry Using Hemispherical Geometry
E1345 Practice for Reducing the Effect of Variability of Color Measurement by Use of Multiple Measurements
E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
E1348 Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry
E1349 Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry
1
This practice is under the jurisdiction of ASTM Committee E12 on Color and Appearance and is the direct responsibility of Subcommittee E12.04 on Color and
Appearance Analysis.
Current edition approved Jan. 1, 2015May 1, 2020. Published February 2015May 2020. Originally approved in 1967. Last previous edition approved in 20102015 as
ɛ1
E313 – 10.E313 – 15 . DOI: 10.1520/E0313-15E01.10.1520/E0313-20.
2
The boldface numbers in parentheses refer to the list of references at the end of this practice.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org. Replaced by Section 6 of E313.
5
The last approved versionReplaced by Section 6 of E313this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 -------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D1535-14(2023)(Practice)
Standard Practice for Specifying Color by the Munsell System

SIGNIFICANCE AND USE
4.1 This practice is used by artists, designers, scientists, engineers, and government regulators, to specify an existing or desired color. It is used in the natural sciences to record the colors of specimens, or identify specimens, such as human complexion, flowers, foliage, soils, and minerals. It is used to specify colors for commerce and for control of color-production processes, when instrumental color measurement is not economical. The Munsell system is widely used for color tolerancing, even when instrumentation is employed (see Practice D3134). It is common practice to have color chips made to illustrate an aim color and the just tolerable deviations from that color in hue, value, and chroma, such a set of chips being called a Color Tolerance Set. A color tolerance set exhibits the aim color and color tolerances so that everyone involved in the selection, production, and acceptance of the color can directly perceive the intent of the specification, before bidding to supply the color or starting production. A color tolerance set may be measured to establish instrumental tolerances. Without extensive experience, it may be impossible to visualize the meaning of numbers resulting from color measurement, but by this practice, the numbers can be translated to the Munsell color-order system, which is exemplified by colored chips for visual examination. This color-order system is the basis of the ISCC-NBS Method of Designating Colors and a Dictionary of Color Names, as well as the Universal Color Language, which associates color names, in the English language, with Munsell notations (3).
SCOPE
1.1 This practice provides a means of specifying the colors of objects in terms of the Munsell color order system, a system based on the color-perception attributes hue, lightness, and chroma. The practice is limited to opaque objects, such as painted surfaces viewed in daylight by an observer having normal color vision. This practice provides a simple visual method as an alternative to the more precise and more complex method based on spectrophotometry and the CIE system (see Practices E308 and E1164). Provision is made for conversion of CIE data to Munsell notation.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    41 pages
    English language
    sale 15% off
ASTM
ASTM D2244-23(Practice)
Standard Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates

SIGNIFICANCE AND USE
5.1 The original CIE color scales based on tristimulus values X, Y, Z and chromaticity coordinates x, y are not uniform visually. Each subsequent color scale based on CIE values has had weighting factors applied to provide some degree of uniformity so that color differences in various regions of color space will be more nearly comparable. On the other hand, color differences obtained for the same specimens evaluated in different color-scale systems are not likely to be identical. To avoid confusion, color differences among specimens or the associated tolerances should be compared only when they are obtained for the same color-scale system. There is no simple factor that can be used to convert accurately color differences or color tolerances in one system to difference or tolerance units in another system for all colors of specimens.  
5.2 Color differences calculated in ΔE00 units (6) are highly recommended for use with color-differences in the range of 0.0 to 5.0 ΔE*ab units. This color-difference equation is appropriate for and widely used in industrial and commercial applications including, but not limited to, automobiles, coatings, cosmetics, inks, packaging, paints, plastics, printing, security, and textiles.  
5.3 Users of color tolerance equations have found that, in each system, summation of three, vector color-difference components into a single scalar value is very useful for determining whether a specimen color is within a specified tolerance from a standard. However, for control of color in production, it may be necessary to know not only the magnitude of the departure from standard but also the direction of this departure. It is possible to include information on the direction of a small color difference by listing the three instrumentally determined components of the color difference.  
5.4 Selection of color tolerances based on instrumental values should be carefully correlated with a visual appraisal of the acceptability of differences in hue, lig...
SCOPE
1.1 This practice covers the calculation, from instrumentally measured color coordinates based on daylight illumination, of color tolerances and small color differences between opaque specimens such as painted panels, plastic plaques, or textile swatches. Where it is suspected that the specimens may be metameric, that is, possess different spectral curves though visually alike in color, Practice D4086 should be used to verify instrumental results. The tolerances and differences determined by these procedures are expressed in terms of approximately uniform visual color perception in CIE 1976 CIELAB opponent-color space (1),2 CMC tolerance units (2), CIE94 tolerance units (3), the DIN99o color difference formula given in DIN 6176  (4), or the CIEDE2000 color difference units (5).  
1.2 For product specification, the purchaser and the seller shall agree upon the permissible color tolerance between test specimen and reference and the procedure for calculating the color tolerance. Each material and condition of use may require specific color tolerances because other appearance factors, (for example, specimen proximity, gloss, and texture), may affect the correlation between the magnitude of a measured color difference and its commercial acceptability.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM E2867-14(2023)(Practice)
Standard Practice for Estimating Uncertainty of Test Results Derived from Spectrophotometry

SIGNIFICANCE AND USE
5.1 Many competent measurement laboratories comply with accepted quality system requirements such as ISO 9001, QS 9000, or ISO 17025. When using standard test methods, the measurement results should agree with those from other similar laboratories within the combined uncertainty limits of the laboratories’ measurement systems. It is for this reason that quality system requirements demand that a statement of the uncertainty of the test results accompany every test result.  
5.2 Preparation of uncertainty estimates is a requirement for laboratory certification under ISO 17025. This practice describes the procedures by which such uncertainty estimates may be calculated.
SCOPE
1.1 This practice describes a protocol to be utilized by measurement laboratories for estimating and reporting the uncertainty of a measurement result when the result is derived from a measurand that has been obtained by spectrophotometry.  
1.2 This practice is specifically limited to the reporting of uncertainty of color measurement results that are reported as color-differences in ΔE format, even though the measurement itself may be reported in other units such as percent reflectance or transmittance.  
1.3 The procedures defined here are not intended to be applicable to national standardizing laboratories or transfer laboratories.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E1164-12(2023)e1(Practice)
Standard Practice for Obtaining Spectrometric Data for Object-Color Evaluation

SIGNIFICANCE AND USE
5.1 The most general and reliable methods for obtaining CIE tristimulus values or, through transformation of them, other coordinates for describing the colors of objects are by the use of spectrometric data. Colorimetric data are obtained by combining object spectral data with data representing a CIE standard observer and a CIE standard illuminant, as described in Practice E308.  
5.2 This practice provides procedures for selecting the operating parameters of spectrometers used for providing data of the desired precision. It also provides for instrument calibration by means of material standards, and for selection of suitable specimens for obtaining precision in the measurements.
SCOPE
1.1 This practice covers the instrumental measurement requirements, calibration procedures, and material standards needed to obtain precise spectral data for computing the colors of objects.  
1.2 This practice lists the parameters that must be specified when spectrometric measurements are required in specific methods, practices, or specifications.  
1.3 Most sections of this practice apply to both spectrometers, which can produce spectral data as output, and spectrocolorimeters, which are similar in principle but can produce only colorimetric data as output. Exceptions to this applicability are noted.  
1.4 This practice is limited in scope to spectrometers and spectrocolorimeters that employ only a single monochromator. This practice is general as to the materials to be characterized for color.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E1477-98a(2022)(Test Method)
Standard Test Method for Luminous Reflectance Factor of Acoustical Materials by Use of Integrating-Sphere Reflectometers

SIGNIFICANCE AND USE
5.1 Acoustical materials are often used as the entire ceiling of rooms and are therefore an important component of the lighting system. The luminous reflectance of all important components must be known in order to predict the level of illumination that will be obtained.  
5.2 The reflecting properties of a surface are measured relative to those of a standard reflector, the perfect reflecting diffuser, to provide a reflectance factor. The luminous reflectance factor is calculated for a standard illuminant, and a standard observer, for the standard hemispherical (integrating-sphere) geometry of illumination and viewing, in which all reflected radiation from an area of the surface is collected. In this way the reflecting properties of an acoustical material can be represented by a single number measured and calculated under standard conditions.  
5.3 Acoustical materials generally have a non-glossy white or near-white finish. The types of surface cover a wide range from smooth to deeply fissured. Measurement with integrating-sphere reflectometers has been satisfactory although multiple measurements may be required to sample the surface adequately. Instruments with other types of optical measuring systems may be used if it can be demonstrated that they provide equivalent results.  
5.4 The use of this test method for determining the luminous reflectance factor is required by Classification E1264.
SCOPE
1.1 This test method covers the measurement of the luminous reflectance factor of acoustical materials for use in predicting the levels of room illumination.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM E2970-22(Practice)
Standard Practice for Specifying Color by the Natural Colour System (NCS)

SIGNIFICANCE AND USE
5.1 The Natural Colour System is a color notation system that builds on how a human being sees color. An NCS notation represents a specific color percept and describes the color as perceived; it is not dependent on limitations caused by pigments, light rays or nerve signals that have given rise to this perception. The NCS system is used internationally in such fields as architecture, corporate identity, cosmetics, education, fashion and textile forecasting and production, interior design and product design. The Natural Colour System describes colors exactly as they are seen. Any of the millions of colors that exist can be defined within the NCS system and given a precise notation. When the NCS system is known, it is possible to judge the attributes of a color by its NCS notation; for example, how much blackness, how much chromaticness, and what hue? This helps to communicate and check specifications and to identify colors. Some examples of the use of NCS are: (1) Architects and designers use the NCS color samples to select colors for all kind of products and materials; (2) They also use the NCS notation to analyze the colors in use in a particular area and to document their specifications; (3) Companies use the NCS color samples as the production standards for their products; (4) Paint manufacturers and other industries use the NCS notation and the NCS color samples to visualize the color of their products to customers, and (5) Companies use the NCS samples as high quality color standards in corporate identity programs and manuals.
SCOPE
1.1 The Natural Colour System (NCS) (see 1.7) provides a color notation system that can be used to communicate color. This practice introduces the Natural Colour System, its terminology, and conversion to and from CIE tristimulus values.  
1.2 The system described in this standard includes color percepts that appear to belong to the surface of a material, provided the surface is not perceived to be fluorescent or to exhibit directional color effects.  
1.3 The system does not include colors that appear to belong to translucent or luminescent objects (so-called volume colors and luminous colors), nor does it include other visual properties of the surface layer, such as gloss and texture. An NCS notation does not describe the physical or chemical properties of an object.  
1.4 This practice also specifies the conditions for visual or instrumental determination of the NCS notation of a color sample, defines the relationships between psychometrically determined NCS notations and the corresponding CIE color coordinates which are to be used in this context.  
1.5 For the accuracy requirements associated with NCS standards and NCS color samples, the user is referred to Swedish Standard SS 19104. The colored illustrations in this standard shall not be used as standard color samples in any way. Color illustrations that are shown on screen or in printouts may be significantly different than the original NCS color samples with the same NCS Notation due to limited color reproduction capabilities in screens and printers.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 Acknowledgement—NCS, Natural Colour System is a trademark of the NCS Colour AB Stockholm, Sweden and is protected by copyright (www.ncscolour.com). All rights reserved. Original NCS color samples are only available form NCS Colour AB or any authorized NCS distributor. Commercial use of the NCS System requires a license from NCS Colour AB.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internation...

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM E1349-06(2022)(Test Method)
Standard Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45°:0° or 0°:45°) Geometry

SIGNIFICANCE AND USE
5.1 The most direct and accessible methods for obtaining the color coordinates of object colors are by instrumental measurement using spectrophotometers or spectrocolorimeters with either hemispherical or bidirectional optical measuring systems. This test method provides procedures for such measurement by spectrophotometry using a bidirectional (0:45 or 45:0) optical measuring system. The method for color and color difference measurement using filter colorimeters is contained in Test Method E1347.  
5.2 This test method is especially suitable for measurement of the following types of specimens for the indicated uses (see also Guide E179 and Practice E805):  
5.2.1 Object-color specimens of any gloss level for color assessment.  
5.2.2 Object-color specimens with physically flat, smooth surfaces from which to obtain data for use in computer colorant formulation.  
5.2.3 Retroreflective specimens.
Note 1: To ensure inter-instrument agreement in the measurement of specimens with intermediate gloss, for formulation, or of retroreflective specimens, significantly tighter tolerances than those given in Practice E1164, Influx and Efflux Conditions, 45°:Normal (45:0) and Normal:45° (0:45) Reflectance Factor section, may be required for the instrument angles of illumination and viewing. Information on the required tolerances is being developed.  
5.3 This test method is not recommended for measurement of specimens with bare metal surfaces for color assessment, for which the use of hemispherical measurement geometry, as with an integrating-sphere type instrument, is preferable (see Guide E179).
SCOPE
1.1 This test method covers the instrumental measurement of the reflection properties and color of object-color specimens by use of a spectrophotometer or spectrocolorimeter with a bidirectional optical measuring system, such as annular, circumferential, or uniplanar 45:0 or 0:45 geometry.  
1.2 This test method is generally suitable for any non-fluorescent, flat object-color specimen. It is especially recommended for measuring retroreflective specimens and specimens of intermediate gloss.  
1.3 Procedures required for the measurement of fluorescent object color are given in Practice E991 and Practice E2153.  
1.4 Procedures required for the measurement of color using filter colorimeters are contained in Test Method E1347 and this standard does not address those instruments.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E2301-12(2022)(Test Method)
Standard Test Method for Daytime Colorimetric Properties of Fluorescent Retroreflective Sheeting and Marking Materials for High Visibility Traffic Control and Personal Safety Applications Using 45°:Normal Geometry

SIGNIFICANCE AND USE
5.1 This test method provides procedures for obtaining tristimulus values, luminance factors and chromaticity coordinates of fluorescent-retroreflective materials by bispectral colorimetry using a 45:0 or 0:45 optical measuring system.  
5.2 The CIE 1931 (2°) standard observer is used to calculate the colorimetric properties of fluorescent-retroreflective sheeting and markings used in daytime high visibility traffic control and personal safety applications because in practice these materials are primarily viewed from a distance where they subtend less than 4° of the visual field.  
5.3 This test method is applicable to object-color specimens of any gloss level.  
5.4 Due to the retroreflective properties of these materials the colorimetric data may not be suitable for use in computer colorant formulation.  
5.5 This test method is suitable for quality control testing of fluorescent-retroreflective sheeting and marking materials.
Note 1: Separation of the fluorescence and reflectance components from the total colorimetric properties provides useful and meaningful information to evaluate independently the luminescent and diffuse reflective efficiency and consistency of these materials.  
5.6 This test method is the referee method for determining the conformance of fluorescent-retroreflective sheeting and marking materials to standard daytime colorimetric specifications.
SCOPE
1.1 This test method describes the instrumental measurement of the colorimetric properties (CIE tristimulus values, luminance factors, and chromaticity coordinates) of fluorescent-retroreflective sheeting and marking materials when illuminated by daylight.  
1.2 This test method is generally applicable to any sheeting or marking material having combined fluorescent and retroreflective properties used for daytime high visibility traffic control and personal safety applications.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1682-08(2022)(Guide)
Standard Guide for Modeling the Colorimetric Properties of a CRT-Type Visual Display Unit

SIGNIFICANCE AND USE
5.1 The color displayed on a VDU is an important aspect of the reproduction of colored images. The VDU is often used as the design, edit, and approval medium. Images are placed into the computer by some sort of capture device, such as a camera or scanner, modified by the computer operator, and sent on to a printer or color separation generator, or even to a paint dispenser or textile dyer. The color of the final product is to have some well-defined relationship to the original. The most common medium for establishing the relationship between input, edit, and output color (device-independent color space) is the CIE tristimulus space. This guide identifies the procedures for deriving a model that relates the digital computer settings of a VDU to the CIE tristimulus values of the colored light emitted by the primaries.
SCOPE
1.1 This guide is intended for use in establishing the operating characteristics of a visual display unit (VDU), such as a cathode ray tube (CRT). Those characteristics define the relationship between the digital information supplied by a computer, which defines an image, and the resulting spectral radiant exitance and CIE tristimulus values. The mathematical description of this relationship can be used to provide a nearby device-independent model for the accurate display of color and colored images on the VDU. The CIE tristimulus values referred to here are those calculated from the CIE 1931 2° standard colorimetric (photopic) observer.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM E1348-22(Test Method)
Standard Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry

SIGNIFICANCE AND USE
5.1 The most direct and accessible methods for obtaining the color coordinates of object colors are by instrumental measurement using spectrophotometers or colorimeters with either hemispherical or bidirectional optical measuring systems. This test method provides procedures for such measurement by transmittance spectrophotometry using a hemispherical optical measuring system.  
5.2 This test method is especially suitable for measurement of the following types of specimens (see also Guide E179 and Practice E805):  
5.2.1 Fully transparent specimens (free from turbidity, haze, or translucency), and  
5.2.2 Translucent or hazy specimens, provided that the specimen can be placed flush against the transmission port of the integrating sphere.  
5.3 This test method is not recommended for measurement of retroreflective transparent or translucent specimens, or samples that are fluorescent.
SCOPE
1.1 This test method describes the instrumental measurement of the transmission properties and color of object-color specimens by the use of a spectrophotometer or spectrocolorimeter with a hemispherical optical measuring system, such as an integrating sphere.  
1.2 This test method is generally suitable for all fully transparent specimens without regard for the specimen position relative to the transmission port of the instrument. Translucent specimens, however, must be placed flush against the transmission port of the sphere.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off