iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3394-94(2005)

(Test Method)

Standard Test Methods for Sampling and Testing Electrical Insulating Board

Standard Test Methods for Sampling and Testing Electrical Insulating Board

SIGNIFICANCE AND USE
Apparent density affects the dielectric and physical characteristics of insulating board and is a factor in the economics of its use in apparatus. This test is useful for specification, design, and quality control purposes.
SCOPE
1.1 These test methods cover the sampling and testing of electrical insulating boards. These boards are porous, usually fibrous sheets used for dielectric and structural purposes in electrical apparatus.
1.2 These test methods are not intended for testing vulcanized fibre or molded laminated sheets.
1.3 These test methods are applicable to board materials having a nominal thickness of at least 0.030 in. (0.76 mm). Note 1 For materials thinner than 0.030 in. (0.76 mm) see Test Methods D 202.
1.4 The test methods appear in the following sections:
1.5 The values stated in inch-pound units are to be regarded as the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Aug-2005
ICS
29.035.01 - Insulating materials in general
Technical Committee
D09 - Electrical and Electronic Insulating Materials
Current Stage
Ref Project

Relations

Replaces
ASTM D3394-94(2000) - Standard Test Methods for Sampling and Testing Electrical Insulating Board
Effective Date
01-Sep-2005
Replaced By
ASTM D3394-94(2009) - Standard Test Methods for Sampling and Testing Electrical Insulating Board
Effective Date
01-Oct-2009
Referred By
ASTM D2413-16(2022) - Standard Practice for Preparation of Insulating Paper and Board Impregnated with a Liquid Dielectric
Effective Date
01-Sep-2005
Referred By
ASTM D202-23 - Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation
Effective Date
01-Sep-2005
Referred By
ASTM D4063-99(2022) - Standard Specification for Pressboard for Electrical Insulating Purposes
Effective Date
01-Sep-2005

Buy Standard

ASTM D3394-94(2005) - Standard Test Methods for Sampling and Testing Electrical Insulating BoardASTM D3394-94(2005) - Standard Test Methods for Sampling and Testing Electrical Insulating Board
PreviousNext
Standard
ASTM D3394-94(2005) - Standard Test Methods for Sampling and Testing Electrical Insulating Board
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation:D3394–94 (Reapproved 2005)
Standard Test Methods for
1
Sampling and Testing Electrical Insulating Board
This standard is issued under the fixed designation D3394; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 These test methods cover the sampling and testing of 2.1 ASTM Standards:
electrical insulating boards. These boards are porous, usually D149 Test Method for Dielectric Breakdown Voltage and
fibrous sheets used for dielectric and structural purposes in Dielectric Strength of Solid Electrical Insulating Materials
electrical apparatus. at Commercial Power Frequencies
1.2 These test methods are not intended for testing vulca- D202 Test Methods for Sampling and Testing Untreated
nized fibre or molded laminated sheets. Paper Used for Electrical Insulation
1.3 These test methods are applicable to board materials D374 Test Methods for Thickness of Solid Electrical Insu-
having a nominal thickness of at least 0.030 in. (0.76 mm). lation
D586 Test Method for Ash in Pulp, Paper, and Paper
NOTE 1—For materials thinner than 0.030 in. (0.76 mm) see Test
3
Products
Methods D202.
D644 Test Method for Moisture Content of Paper and
1.4 The test methods appear in the following sections:
Paperboard by Oven Drying
ASTM Method
D664 Test Method forAcid Number of Petroleum Products
Sections Reference
by Potentiometric Titration
Apparent Density 18-23
Aqueous Extract Characteristics 36-42 D202
D685 Practice for Conditioning Paper and Paper Products
Ash Content 43-46 T 413
for Testing
Compatibility with Dielectric 47-52 D664, D877, D924,
D877 Test Method for Dielectric Breakdown Voltage of
Liquids D971, D974, D1169,
D1500, D1816,
Insulating Liquids Using Disk Electrodes
D3455, D3487
D924 Test Method for Dissipation Factor (or Power Factor)
Compressibility 79-85
and Relative Permittivity (Dielectric Constant) of Electri-
Conditioning 11 D685
Degree of Polymerization 86-89 D4243
cal Insulating Liquids
Dielectric Strength in Air 53-59 D149
D971 Test Method for Interfacial Tension of Oil Against
Dielectric Strength in Oil 60-65 D149, D2413, D3426
Water by the Ring Method
Dimensions of Sheets 12-17
Moisture Content 31-35 D644
D974 Test Method for Acid and Base Number by Color-
Oil Absorption 72-78
Indicator Titration
Reports 10
D1169 Test Method for Specific Resistance (Resistivity) of
Sampling 6-9 D3636
Shrinkage 24-30 D644
Electrical Insulating Liquids
Tensile Properties 66-71 D202
D1500 TestMethodforASTMColorofPetroleumProducts
1.5 The values stated in inch-pound units are to be regarded
(ASTM Color Scale)
as the standard. D1816 Test Method for Dielectric Breakdown Voltage of
1.6 This standard does not purport to address all of the
InsulatingOilsofPetroleumOriginUsingVDEElectrodes
safety concerns, if any, associated with its use. It is the D2413 Practice for Preparation of Insulating Paper and
responsibility of the user of this standard to consult and
Board Impregnated with a Liquid Dielectric
establish appropriate safety and health practices and deter- D2865 Practice for Calibration of Standards and Equipment
mine the applicability of regulatory limitations prior to use.
for Electrical Insulating Materials Testing
1 2
These test methods are under the jurisdiction of ASTM Committee D09 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Electrical and Electronic Insulating Materials and are the direct responsibility of contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Subcommittee D09.19 on Dielectric Sheet and Roll Products. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Sept. 1, 2005. Published October 2005. Originally the ASTM website.
3
approved in 1975. Last previous edition approved in 2000 as D3394 – 94 (2000). Withdrawn. The last approved version of this historical standard is referenced
DOI: 10.1520/D3394-94R05.
on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3394–94 (2005)
D3426 Test Method for Dielectric Breakdown Voltage and 7.1.2 unit of product—an entity of electrical insulating
Dielectric Strength of Solid Electrical Insulating Materials board on which one or more quality characteristics may be
Using Impulse Waves determined. A unit of product may be a sheet, pallet, box,
D3455 Test Methods for Compatibility of Construction carton, case, package, or bundle. The unit of product is
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D374/D374M-23(Test Method)
Standard Test Methods for Thickness of Solid Electrical Insulation

SIGNIFICANCE AND USE
5.1 Some electrical properties, such as dielectric strength, vary with the thickness of the material. Determination of certain properties, such as relative permittivity (dielectric constant) and volume resistivity, usually require a knowledge of the thickness. Design and construction of electrical machinery require that the thickness of insulation be known.
SCOPE
1.1 These test methods cover the determination of the thickness of several types of solid electrical insulating materials employing recommended techniques. Use these test methods except as otherwise required by a material specification.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D2132-23(Test Method)
Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials

SIGNIFICANCE AND USE
6.1 Method—It is possible that electrical insulation in service will fail as a result of tracking, erosion, or a combination of both, if exposed to high relative humidity and contamination environments. This is particularly true of organic insulations in outdoor applications where the surface of the insulation becomes contaminated by deposits of moisture and dirt, for example, coal dust or salt spray. This test method is an accelerated test that simulates extremely severe outdoor contamination. It is believed that the most severe conditions likely to be encountered in outdoor service in the United States will be relatively mild compared to the conditions specified in this test method.  
6.2 Test Results—Materials can be classified by this test method as tracking-resistant, tracking-affected, or tracking-susceptible. The exact test values for these categories as they apply to specific uses will be specified in the appropriate material specifications, but guideline figures are suggested in Note 4. Tracking-resistant materials, unless erosion failure occurs first, have the potential to last many hundreds of hours (Note 5). Erosion, though it is possible that it will progress laterally, generally results in a failure perpendicular to the specimen surface. Therefore, compare only specimens of the same nominal thickness for resistance to tracking-induced erosion. Estimate the extent of erosion from measurements of the depth of penetration of the erosion. Place materials that are not tracking-susceptible in three broad categories—erosion-resistant, erosion-affected, and erosion-susceptible. When the standard thickness specimen is tested, the following times to failure typify the categories (Note 6):    
Erosion-susceptible  
5 h to 50 h  
Erosion-affected  
50 h to 200 h  
Erosion-resistant  
over 200 h
Note 4: Tracking-susceptible materials usually fail within 5 h. Tracking-affected materials usually fail before about 100 h.
Note 5: This information is derive...
SCOPE
1.1 This test method is intended to differentiate solid electrical insulating materials with respect to their resistance to the action of electric arcs produced by conduction through surface films of a specified contaminant containing moisture. Test Methods D2302, D2303, D3638, and D5288 are also useful to evaluate materials.  
1.2 Units—The values stated in SI units are the standard. The inch-pound units in parentheses are for information only. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no equivalent ISO standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5424-23a(Test Method)
Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

SIGNIFICANCE AND USE
5.1 This test method provides a means to measure a variety of fire-test-response characteristics associated with smoke obscuration and resulting from burning the electrical insulating materials contained in electrical or optical fiber cables. The specimens are allowed to burn freely under well ventilated conditions after ignition by means of a propane gas burner.  
5.2 Smoke obscuration quantifies the visibility in fires.  
5.3 This test method is also suitable for measuring the rate of heat release as an optional measurement. The rate of heat release often serves as an indication of the intensity of the fire generated. Test Method D5537 provides means for measuring heat release with the equipment used in this test method.  
5.4 Other optional fire-test-response characteristics that are measurable by this test method are useful to make decisions on fire safety. The most important gaseous components of smoke are the carbon oxides, present in all fires. They are major indicators of the toxicity of the atmosphere and of the completeness of combustion, and are often used as part of fire hazard assessment calculations and to improve the accuracy of heat release measurements. Other toxic gases, which are specific to certain materials, are less crucial for determining combustion completeness.  
5.5 Test Limitations:  
5.5.1 The fire-test-response characteristics measured in this test method are a representation of the manner in which the specimens tested behave under certain specific conditions. Do not assume they are representative of a generic fire performance of the materials tested when made into cables of the construction under consideration.  
5.5.2 In particular, it is unlikely that this test method is an adequate representation of the fire behavior of cables in confined spaces, without abundant circulation of air.  
5.5.3 This is an intermediate-scale test, and the predictability of its results to large scale fires has not been determined. Some information ...
SCOPE
1.1 This is a fire-test-response standard.  
1.2 This test method provides a means to measure the smoke obscuration resulting from burning electrical insulating materials contained in electrical or optical fiber cables when the cable specimens, excluding accessories, are subjected to a specified flaming ignition source and burn freely under well ventilated conditions.  
1.3 This test method provides two different protocols for exposing the materials, when made into cable specimens, to an ignition source (approximately 20 kW), for a 20 min test duration. Use it to determine the flame propagation and smoke release characteristics of the materials contained in single and multiconductor electrical or optical fiber cables designed for use in cable trays.  
1.4 This test method does not provide information on the fire performance of electrical or optical fiber cables in fire conditions other than the ones specifically used in this test method, nor does it measure the contribution of the cables to a developing fire condition.  
1.5 Data describing the burning behavior from ignition to the end of the test are obtained.  
1.6 The production of light obscuring smoke is measured.  
1.7 The burning behavior is documented visually, by photographic or video recordings, or both.  
1.8 The test equipment is suitable for making other, optional, measurements, including the rate of heat release of the burning specimen, by an oxygen consumption technique and weight loss.  
1.9 Another set of optional measurements are the concentrations of certain toxic gas species in the combustion gases.  
1.10 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See IEEE/ASTM SI 10.)  
1.11 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety...

  • Standard
    21 pages
    English language
    sale 15% off
  • Standard
    21 pages
    English language
    sale 15% off
ASTM
ASTM D2304-23(Test Method)
Standard Test Method for Thermal Endurance of Rigid Electrical Insulating Materials

SIGNIFICANCE AND USE
6.1 Thermal degradation is often a major factor affecting the life of insulating materials and the equipment in which they are used. The temperature index provides a means for comparing the thermal capability of different materials in respect to the degradation of a selected property (the aging criterion). This property needs to directly or indirectly represent functional needs in application. For example, it is possible that a change in dielectric strength will be of direct, functional importance. However, more often it is possible that a decrease in dielectric strength will indirectly indicate the development of undesirable cracking (embrittlement). A decrease in flexural strength has the potential to be of direct importance in some applications, but also has the potential to indirectly indicate a susceptibility to failure in vibration. Often, it is necessary that two or more criteria of failure be used; for example, dielectric strength and flexural strength.  
6.2 Other factors, such as vibration, moisture and contaminants, have the potential to cause failure after thermal degradation takes place. In this test method, water absorption provides one means to evaluate such considerations.  
6.3 For some applications, the aging criteria in this test method will not be the most suitable. Other criteria, such as elongation at tensile or flexural failure, or resistivity after exposure to high humidity or weight loss, have the potential to serve better. The procedures in this test method have the potential to be used with such aging criteria. It is important to consider both the nature of the material and its application. For example, it is possible that tensile strength will be a poor choice for glass-fiber reinforced laminates, because it is possible that the glass fiber will maintain the tensile strength even when the associated resin is badly deteriorated. In this case, flexural strength is a better criterion of thermal aging.  
6.4 When dictated by the needs of t...
SCOPE
1.1 This test method2 provides procedures for evaluating the thermal endurance of rigid electrical insulating materials. Dielectric strength, flexural strength, or water absorption are determined at room temperature after aging for increasing periods of time in air at selected-elevated temperatures. A thermal-endurance graph is plotted using a selected end point at each aging temperature. A means is described for determining a temperature index by extrapolation of the thermal endurance graph to a selected time.  
1.2 This test method is most applicable to rigid electrical insulation such as supports, spacers, voltage barriers, coil forms, terminal boards, circuit boards and enclosures for many types of application where retention of the selected property after heat aging is important.  
1.3 When dielectric strength is used as the aging criterion, it is also acceptable to use this test method for some thin sheet (flexible) materials, which become rigid with thermal aging, but is not intended to replace Test Method D1830 for those materials which must retain a degree of flexibility in use.  
1.4 This test method is not applicable to ceramics, glass, or similar inorganic materials.  
1.5 The values stated in metric units are to be regarded as standard. Other units (in parentheses) are provided for information.  
1.6 When determining the thermal endurance of rigid EIM, the basic concepts in this standard follow IEEE 1, IEEE 98, and IEEE 101.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 11.3.4.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization establis...

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D5537-23a(Test Method)
Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables When Burning in a Vertical Cable Tray Configuration

SIGNIFICANCE AND USE
5.1 This test method provides a means to measure a variety of fire-test-response characteristics associated with heat and smoke release and resulting from burning the materials insulating electrical or optical fiber cables, when made into cables and installed on a vertical cable tray. The specimens are allowed to burn freely under well ventilated conditions after ignition by means of a propane gas burner. The ignition source used in this test method is also described as a premixed flame flaming ignition source in Practice E3020, which contains an exhaustive compilation of ignition sources.  
5.2 The rate of heat release often serves as an indication of the intensity of the fire generated. General considerations of the importance of heat release rate are discussed in Appendix X1 and considerations for heat release calculations are in Appendix X2.  
5.3 Other fire-test-response characteristics that are measurable by this test method are useful to make decisions on fire safety. The test method is also used for measuring smoke obscuration. The apparatus described here is also useful to measure gaseous components of smoke; the most important gaseous components of smoke are the carbon oxides, present in all fires. The carbon oxides are major indicators of the completeness of combustion and are often used as part of fire hazard assessment calculations and to improve the accuracy of heat release measurements.  
5.4 Test Limitations:  
5.4.1 The fire-test-response characteristics measured in this test are a representation of the manner in which the specimens tested behave under certain specific conditions. Do not assume they are representative of a generic fire performance of the materials tested when made into cables of the construction under consideration.  
5.4.2 In particular, it is unlikely that this test is an adequate representation of the fire behavior of cables in confined spaces, without abundant circulation of air.  
5.4.3 This is an intermediate-scale test...
SCOPE
1.1 This is a fire-test-response standard.  
1.2 This test method provides a means to measure the heat released and smoke obscuration by burning the electrical insulating materials contained in electrical or optical fiber cables when the cable specimens, excluding accessories, are subjected to a specified flaming ignition source and burn freely under well ventilated conditions. Flame propagation cable damage, by char length, and mass loss are also measured.  
1.3 This test method provides two different protocols for exposing the materials, when made into cable specimens, to an ignition source (approximately 20 kW), for a 20 min test duration. Use it to determine the heat release, smoke release, flame propagation and mass loss characteristics of the materials contained in single and multiconductor electrical or optical fiber cables.  
1.4 This test method does not provide information on the fire performance of materials insulating electrical or optical fiber cables in fire conditions other than the ones specifically used in this test method nor does it measure the contribution of the materials in those cables to a developing fire condition.  
1.5 Data describing the burning behavior from ignition to the end of the test are obtained.  
1.6 This test equipment is suitable for measuring the concentrations of certain toxic gas species in the combustion gases (see Appendix X4).  
1.7 The values stated in SI units are to be regarded as standard (see IEEE/ASTM SI-10). The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.8 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions  
...

  • Standard
    21 pages
    English language
    sale 15% off
  • Standard
    21 pages
    English language
    sale 15% off
ASTM
ASTM D6194-23(Test Method)
Standard Test Method for Glow-Wire Ignition of Materials

SIGNIFICANCE AND USE
5.1 During operation of electrical equipment, including wires, resistors, and other conductors, it is possible for overheating to occur under certain conditions of operation, or when malfunctions occur. When this happens, a possible result is ignition of the adjacent insulation material.  
5.2 This test method assesses the susceptibility of electrical insulating materials to ignition as a result of exposure to a glowing wire.  
5.3 This test method determines the minimum temperature required to ignite a material by the effect of a glowing heat source, under the specified conditions of test.  
5.4 This method is suitable, subject to the appropriate limitations of an expected precision of ±15 %, to categorize materials.  
5.5 In this procedure, the specimens are subjected to one or more specific sets of laboratory conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.
SCOPE
1.1 This test method covers the minimum temperature required to ignite insulating materials using a glowing heat source. In a preliminary fashion, this test method differentiates between the susceptibilities of different materials with respect to their resistance to ignition due to an electrically-heated source.  
1.2 This test method applies to molded or sheet materials available in thicknesses ranging from 0.25 mm to 6.4 mm.  
1.3 This test method is not valid for determining the ignition behavior of complete electrotechnical equipment, since the design of the electrotechnical product influences the heat transfer between adjacent parts.  
1.4 This test method measures and describes the response or materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. (See IEEE/ASTM SI-10 for further details.)For specific precautionary statements, see Section 9.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9.  
1.7 Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
Note 1: Although this test method and IEC 60695-2-12 differ in approach and in detail, data obtained to determine the glow-wire flammability index (GWFI) using either test method are technically similar. Although this test method and IEC 60695-2-13 differ in approach and in detail, data obtained to determine the glow-wire ignition temperature (GWIT) using either test method are technically similar.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5374-22a(Test Method)
Standard Test Methods for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation

SIGNIFICANCE AND USE
4.1 Ovens used for thermal evaluation of insulating materials are to be capable of maintaining uniform conditions of temperature and air circulation over the extended periods of time that are required for conducting these tests. Specification D5423 specifies the permissible variations from absolute uniformity that have been accepted internationally for these ovens. These test methods include procedures for measuring these variations and other specified characteristics of the ovens.
SCOPE
1.1 These test methods cover procedures for evaluating the characteristics of forced-convection ventilated electrically-heated ovens, operating over all or part of the temperature range from 20 °C above the ambient temperature to 500 °C and used for thermal endurance evaluation of electrical insulating materials.  
1.2 These test methods are based on IEC Publication 60216-4-1, and are technically identical to it. This compilation of test methods and an associated specification, D5423, have replaced Specification D2436.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D1711-22(Terminology)
Standard Terminology Relating to Electrical Insulation

SCOPE
1.1 This terminology standard is a compilation of technical terms associated with testing and specifying solid electrical and electronic insulating materials.  
1.2 This terminology standard shall contain all definitions that are balloted specifically through Subcommittee D09.94 and through D09 main committee and that are of general interest to standards associated with electrical and electronic insulating materials. Those definitions shall be of importance to electrical and electronic insulating materials issues but need not be directly associated with a specific standard under the jurisdiction of Committee D09 on Electrical and Electronic Insulating Materials.  
1.3 It is intended that all definitions in this terminology standard originating in a specific standard under the jurisdiction of Committee D09 be identical to definitions of the same terms as printed in standards of originating technical subcommittees, with the exceptions of: (1) deletion of any part of the Discussion included in another standard that refers specifically to the use of a term in that standard; (2) figure numbers and corresponding references; and (3) in this terminology standard, a parenthetical addition of a reference to one or more technical standards in which the term is used and the year in which the term was added to this compilation.  
1.3.1 Definitions contained in this terminology standard which did not originate in a specific standard under the jurisdiction of Committee D09, or which originated in a standard that has since been revised or withdrawn, and that have been appropriately balloted, shall also be included in this terminology standard.  
1.4 It is permissible to include symbols as part of the representation of terms, where appropriate.  
1.5 It is not intended that this terminology standard include symbols (except as noted in 1.4). It is also permissible to include acronyms and abbreviations referring directly to defined terms.  
1.6 Revisions and additions to those definitions in this terminology standard which originate in a specific standard under the jurisdiction of Committee D09 are to be made as a product of a collaborative effort between Subcommittee D09.94 and the corresponding technical subcommittee of Committee D09, with Subcommittee D09.94 providing editorial advice to the technical subcommittees.  
1.7 Each definition in this terminology standard shall be accompanied by the year in which it was first incorporated into the standard, placed at the end in parentheses. All discussions shall also carry a date; it is possible that the discussion date is different from the definition date.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    12 pages
    English language
    sale 15% off
  • Standard
    12 pages
    English language
    sale 15% off
ASTM
ASTM D4063-99(2022)(Specification)
Standard Specification for Pressboard for Electrical Insulating Purposes

ABSTRACT
This specification covers pressboard for electrical insulating purposes as well as for dielectrical or structural purposes in transformers and other electrical apparatus. Pressboards under this specification are of three types: Type 1 consists of high-purity (Grade 1.1) calendered pressboards, while Type 2 consists of normal-purity (Grades 2.1.1, 2.2.1, 2.3.1, and 2.3.2) calendered pressboards. Precompressed pressboards (Grades 3.1.1, 3.2.1, and 3.3) fall under Type 3. Not included in this specification, however, are pressboards comprised of two or more sheets laminated together using an adhesive. Pressboards shall be manufactured from unbleached kraft pulp, cotton pulp, or a combination of both, and shall conform to the thickness, density, surface texture (smooth calendered surface for Types1 and 2, and fine-textured finish for Type 3), and color (from tan to blue-gray, depending on the pressboard's grade) requirements specified. The pressboard must also be free of dirt, metal particles, and other foreign material. Tests for apparent density, thickness, moisture and ash content, aqueous extract conductivity, chloride content, tensile strength, pH of aqueous extract, dielectric strength in air and in oil, shrinkage, and compressibility shall be performed and shall conform to the requirements specified.
SCOPE
1.1 This specification covers pressboard for electrical insulating purposes, manufactured from kraft, cotton, or kraft and cotton pulps. This board is intended for dielectrical or structural purposes in transformers and other electrical apparatus.  
1.2 Electrical insulating boards are most commonly referred to (and will be referred to herein) as pressboard. Other terms used for pressboard include transformer board, fuller board, and presspan.  
1.3 This specification covers pressboard having a nominal thickness of 0.030 to 0.315 in. (0.8 to 8.0 mm). For thinner material refer to Specification D1305.  
1.4 The maximum thickness available will differ with the type and the manufacturer. The maximum sheet size will differ with the thickness, type, and manufacturer.  
1.5 Pressboard shall normally be plied wet without pasting. Unless specified by the purchaser, this specification does not include pressboard comprised of two or more sheets that have been laminated together using an adhesive.
Note 1: The materials described in this specification are similar to corresponding types of pressboard described in IEC Specification 641-3, Sheet 1, Types B.0.1, B.2.1, B.2.3, B.3.1, and B.3.3.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3394-16(2022)(Test Method)
Standard Test Methods for Sampling and Testing Electrical Insulating Board

SIGNIFICANCE AND USE
19.1 Apparent density affects the dielectric and physical characteristics of insulating board and is a factor in the economics of its use in apparatus. This test is useful for specification, design, and quality control purposes.
SCOPE
1.1 These test methods cover the sampling and testing of electrical insulating boards. These boards are porous, usually fibrous sheets used for dielectric and structural purposes in electrical apparatus.  
1.2 These test methods are not intended for testing vulcanized fibre or molded laminated sheets.  
1.3 These test methods are applicable to board materials having a nominal thickness of at least 0.030 in. (0.76 mm).  
Note 1: For materials thinner than 0.030 in. (0.76 mm) see Test Methods D202.  
1.4 The test methods appear in the following sections:    
Sections  
ASTM Method
Reference  
Apparent Density  
18 – 23  
Aqueous Extract Characteristics  
36 – 42  
D202  
Ash Content  
43 – 46  
T 413  
Compatibility with Dielectric
Liquids  
47 – 52  
D664, D877, D924,
D971, D974, D1169,
D1500, D1816,
D3455, D3487  
Compressibility  
79 – 85  
Conditioning  
11  
D685  
Degree of Polymerization  
86 – 89  
D4243  
Dielectric Strength in Air  
53 – 59  
D149  
Dielectric Strength in Oil  
60 – 65  
D149, D2413, D3426  
Dimensions of Sheets  
12 – 17  
Moisture Content  
31 – 35  
D644  
Oil Absorption  
72 – 78  
Reports  
10  
Sampling  
6 – 9  
D3636  
Shrinkage  
24 – 30  
D644  
Tensile Properties  
66 – 71  
D202  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to consult and establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off