iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM G190-15

(Guide)

Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)

Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)

SIGNIFICANCE AND USE
5.1 The guidance and methodology provided by this guide is applicable for any wear situation and is not limited to material or lubrication. This guide is intended to provide general information and guidance regarding the selection and development of a wear test and does not provide specifics about any one wear test or intended application. In general the variability and correlation that is obtained with any wear test is determined by the degree to which the various elements of the wear test methodology described in this guide are followed.
SCOPE
1.1 This guide covers general information for the development and selection of a wear test for an intended application.
WITHDRAWN RATIONALE
This guide covers general information for the development and selection of a wear test for an intended application.
Formerly under the jurisdiction of Committee G02 on Wear and Erosion, this guide was withdrawn in November 2021. This guide is being withdrawn without replacement because it has been found to not be useful in selecting a particular wear test. It gives general information regarding wear testing. From the name, one would assume that there is some sort of tree or if/then structure to guide the user in selecting a wear test. This is not the case. As for developing a wear test, clearly if one were to develop a wear test, they would need to be an expert in the area of wear. The brief standard guide would not be helpful in that regard, as it only gives general information. Moreover, the book by Ken Budinski, “Guide to Friction, Wear, and Erosion Testing,” published by ASTM MNL 56 gives a much more in-depth treatment of the topic. The book is useful to both an end user and a test developer. With this in mind, G190 no longer has utility.

General Information

Status
Withdrawn
Publication Date
30-Apr-2015
Withdrawal Date
18-Nov-2021
ICS
19.020 - Test conditions and procedures in general
Technical Committee
G02 - Wear and Erosion
Drafting Committee
G02.91 - Terminology
Current Stage
Ref Project

Buy Standard

ASTM G190-15 - Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)ASTM G190-15 - Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)
PreviousNext
Guide
ASTM G190-15 - Standard Guide for Developing and Selecting Wear Tests (Withdrawn 2021)
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: G190 − 15
Standard Guide for
1
Developing and Selecting Wear Tests
This standard is issued under the fixed designation G190; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope G65 Test Method for Measuring Abrasion Using the Dry
Sand/Rubber Wheel Apparatus
1.1 This guide covers general information for the develop-
G73 Test Method for Liquid Impingement Erosion Using
ment and selection of a wear test for an intended application.
Rotating Apparatus
1.2 This international standard was developed in accor-
G75 Test Method for Determination of Slurry Abrasivity
dance with internationally recognized principles on standard-
(Miller Number) and Slurry Abrasion Response of Mate-
ization established in the Decision on Principles for the
rials (SAR Number)
Development of International Standards, Guides and Recom-
G76 Test Method for Conducting Erosion Tests by Solid
mendations issued by the World Trade Organization Technical
Particle Impingement Using Gas Jets
Barriers to Trade (TBT) Committee.
G77 Test Method for Ranking Resistance of Materials to
Sliding Wear Using Block-on-Ring Wear Test
2. Referenced Documents
G81 Test Method for Jaw Crusher Gouging Abrasion Test
2
2.1 ASTM Standards:
G83 Test Method for Wear Testing with a Crossed-Cylinder
D2266 Test Method for Wear Preventive Characteristics of
3
Apparatus (Withdrawn 2005)
Lubricating Grease (Four-Ball Method)
G98 Test Method for Galling Resistance of Materials
D2670 Test Method for Measuring Wear Properties of Fluid
G99 Test Method for Wear Testing with a Pin-on-Disk
Lubricants (Falex Pin and Vee Block Method)
Apparatus
D2714 Test Method for Calibration and Operation of the
G105 Test Method for Conducting Wet Sand/Rubber Wheel
Falex Block-on-Ring Friction and Wear Testing Machine
Abrasion Tests
D3702 Test Method for Wear Rate and Coefficient of Fric-
G117 Guide for Calculating and Reporting Measures of
tion of Materials in Self-Lubricated Rubbing Contact
Precision Using Data from Interlaboratory Wear or Ero-
Using a Thrust Washer Testing Machine
3
sion Tests (Withdrawn 2016)
D3704 Test Method for Wear Preventive Properties of Lu-
G118 Guide for Recommended Format of Wear Test Data
bricating Greases Using the (Falex) Block on Ring Test
3
Suitable for Databases (Withdrawn 2016)
Machine in Oscillating Motion
G119 Guide for Determining Synergism Between Wear and
D4170 Test Method for Fretting Wear Protection by Lubri-
Corrosion
cating Greases
G132 Test Method for Pin Abrasion Testing
D4172 Test Method for Wear Preventive Characteristics of
G133 Test Method for Linearly Reciprocating Ball-on-Flat
Lubricating Fluid (Four-Ball Method)
Sliding Wear
F732 Test Method for Wear Testing of Polymeric Materials
G134 Test Method for Erosion of Solid Materials by Cavi-
Used in Total Joint Prostheses
tating Liquid Jet
G32 Test Method for Cavitation Erosion Using Vibratory
G137 Test Method for Ranking Resistance of Plastic Mate-
Apparatus
rials to Sliding Wear Using a Block-On-Ring Configura-
G40 Terminology Relating to Wear and Erosion
tion
G56 Test Method forAbrasiveness of Ink-Impregnated Fab-
G163 Guide for Digital Data Acquisition in Wear and
ric Printer Ribbons and Other Web Materials
3
Friction Measurements (Withdrawn 2016)
G171 Test Method for Scratch Hardness of Materials Using
1
This guide is under the jurisdiction of ASTM Committee G02 on Wear and
a Diamond Stylus
Erosion and is the direct responsibility of Subcommittee G02.91 on Terminology.
G174 Test Method for Measuring Abrasion Resistance of
Current edition approved May 1, 2015. Published May 2015. Originally
Materials by Abrasive Loop Contact
approved in 2006. Last previous edition approved in 2006 as G190 – 06 which was
withdrawn January 2015 and reinstated in May 2015. DOI: 10.1520/G0190-15.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
G190 − 15
G176 Test Method for Ranking Resistance of Plastics to tion in the wear test. Another element of the methodology for
Sliding Wear Using Block-on-Ring Wear Test— selecting a wear test is acceleration of wear results, which is
Cumulative Wear Method related to the consideration of simulation.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM G136-03(2023)e1(Practice)
Standard Practice for Determination of Soluble Residual Contaminants in Materials by Ultrasonic Extraction

SIGNIFICANCE AND USE
5.1 This practice is suitable for the determination of extractable substances that may be found in materials used in systems or components requiring a high level of cleanliness, such as oxygen systems. Soft goods, such as seals and valve seats, may be tested as received. Gloves and wipes, or samples thereof, to be used in cleaning operations may be evaluated prior to use to ensure that the proposed extracting agent does not extract or deposit chemicals, or both, on the surface to be cleaned.  
5.2 Wipes or other cleaning equipment may be tested after use to determine the amount of contaminant removed from a surface.
Note 1: The amount of material extracted may be dependent upon the frequency and power density of the ultrasonic unit.  
5.3 The extraction efficiency has been shown to vary with the frequency and power density of the ultrasonic unit. The unit, therefore, must be carefully evaluated to optimize the extraction conditions.
SCOPE
1.1 This practice may be used to extract nonvolatile and semivolatile residues from materials such as new and used gloves, new and used wipes, component soft goods, and so forth. When used with proposed cleaning materials (wipes, gloves, and so forth), this practice may be used to determine the potential of the proposed solvent or other fluids to extract contaminants (plasticizers, residual detergents, brighteners, and so forth) and deposit them on the surface being cleaned.  
1.2 This practice is not suitable for the evaluation of particulate contamination.  
1.3 The values stated in SI units are to be regarded standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D6259-23(Practice)
Standard Practice for Determination of a Pooled Limit of Quantitation for a Test Method

SIGNIFICANCE AND USE
5.1 Background—In a single laboratory, the limit of quantitation, LOQ, equal to ten times the standard deviation obtained under repeatability conditions extrapolated to zero concentration (s0) based on samples with close to zero concentrations has been recommended.3 A test result at this LOQ has an uncertainty of ±30 % at the 99 % confidence level.  
5.1.1 This practice uses a regression technique to determine a similar limit for a test method (PLOQ) using statistically pooled repeatability standard deviations over multiple operators/laboratories/samples from ILS data. This PLOQ can be used by industry to assess the reliability of a test method, or, compare reliability of different test methods, for quantitative measurement at concentrations near zero. Similarly, quantitative test results obtained using the test method for levels at or below the PLOQ can be expected by industry to have an uncertainty of ±30 % or greater at the 95 % confidence level.  
5.1.2 The regression technique described in this practice can also be used to determine a limit of quantitation specific for a single laboratory (LLOQ). The limit thus quantified for one laboratory is defined by this standard as the laboratory limit of quantitation (LLOQ).  
5.1.3 It should be noted that since differences in repeatability testing capabilities between different laboratories can exist, therefore, LLOQ determined at a single laboratory can be different than the PLOQ determined for the test method.  
5.2 Values below the PLOQ are deemed by this practice to be too uncertain for meaningful use in commerce, or in regulatory activities.
SCOPE
1.1 This practice covers the use of standard regression techniques and data from an interlaboratory study to determine a lower quantitative limit for a test method. This determined lower limit represents the numerical limit at or above which the test results are considered to be quantitatively meaningful for commerce or regulatory activities by this practice. It is defined by this standard as the pooled limit of quantitation (PLOQ) for the test method.  
1.2 This practice is applicable to test methods that are capable of producing numerical test results close to zero. Examples are those test methods that determine quantitatively the concentration of analyte(s) near zero.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1488-12(2023)(Guide)
Standard Guide for Statistical Procedures to Use in Developing and Applying Test Methods

ABSTRACT
This guide identifies statistical procedures for use in developing new test methods or revising or evaluating existing test methods, or both. It also cites statistical procedures especially useful in the application of test methods. This standard recommends what approaches may be taken and indicates which standards may be used to perform such assessments.
SIGNIFICANCE AND USE
4.1 The creation of a standardized test method generally follows a series of steps from inception to approval and ongoing use. In all such stages there are questions of how well the test method performs.  
4.1.1 Assessments of a new or existing test method generally involve statistical planning and analysis. This standard recommends what approaches may be taken and indicates which standards may be used to perform such assessments.  
4.2 This standard introduces a series of phases which are recommended to be considered during the life cycle of a test method as depicted in Fig. 1. These begin with a design phase where the standard is initially prepared. A development phase involves a variety of experiments that allow further refinement and understanding of how the test method performs within a laboratory. In an evaluation phase the test method is then examined by way of interlaboratory studies resulting in precision and bias statistics which are published in the standard. Finally, the test method is subject to a monitoring phase.
FIG. 1 Sequence of Steps  
4.3 All ASTM test methods are required to include statements on precision and bias.3  
4.4 Since ASTM began to require all test methods to have precision and bias statements that are based on interlaboratory test methods, there has been increased concern regarding what statistical experiments and procedures to use during the development of the test methods. Although there exists a wide range of statistical procedures, there is a small group of generally accepted techniques that are beneficial to follow. This guide is designed to provide a brief overview of these procedures and to suggest an appropriate sequence of carrying out these procedures.  
4.5 Statistical procedures often result in interpretations that are not absolutes. Sometimes the information obtained may be inadequate or incomplete, which may lead to additional questions and the need for further experimentation. Information outside the data is al...
SCOPE
1.1 This guide identifies statistical procedures for use in developing new test methods or revising or evaluating existing test methods, or both.  
1.2 This guide also cites statistical procedures especially useful in the application of test methods.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    9 pages
    English language
    sale 15% off
ASTM
ASTM E691-23(Practice)
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ABSTRACT
This practice describes the techniques for planning, conducting, analyzing, and treating the results of an interlaboratory study (ILS) of a test method. The statistical techniques described in this practice provide adequate information for formulating the precision statement of a test method. This practice is also concerned exclusively with test methods which yield a single numerical figure as the test result, although the single figure may be the outcome of a calculation from a set of measurements. ASTM regulations require precision statements in all test methods in terms of repeatability and reproducibility and knowledge of the test method precision is useful in commerce and in technical work when comparing test results against standard values or between data sources.
SIGNIFICANCE AND USE
4.1 ASTM regulations require precision statements in all test methods in terms of repeatability and reproducibility. This practice may be used in obtaining the needed information as simply as possible. This information may then be used to prepare a precision statement in accordance with Practice E177. Knowledge of the test method precision is useful in commerce and in technical work when comparing test results against standard values (such as specification limits) or between data sources (different laboratories, instruments, etc.).  
4.1.1 When a test method is applied to a large number of portions of a material that are as nearly alike as possible, the test results obtained will not all have the same value. A measure of the degree of agreement among these test results describes the precision of the test method for that material. Numerical measures of the variability between such test results provide inverse measures of the precision of the test method. Greater variability implies smaller (that is, poorer) precision and larger imprecision.  
4.1.2 Precision is reported as a standard deviation, coefficient of variation (relative standard deviation), variance, or a precision limit (a data range indicating no statistically significant difference between test results).  
4.1.3 This practice is designed only to estimate the precision of a test method. However, when accepted reference values are available for the property levels, the test result data obtained according to this practice may be used in estimating the bias of the test method. For a discussion of bias estimation and the relationships between precision, bias, and accuracy, see Practice E177.  
4.2 The procedures presented in this practice consist of three basic steps: planning the interlaboratory study, guiding the testing phase of the study, and analyzing the test result data.  
4.2.1 The planning phase includes forming the ILS task group, the study design, selection, and number of participating laborato...
SCOPE
1.1 This practice describes the techniques for planning, conducting, analyzing, and treating the results of an interlaboratory study (ILS) of a test method. The statistical techniques described in this practice provide adequate information for formulating the precision statement of a test method.  
1.2 This practice does not concern itself with the development of test methods but rather with gathering the information needed for a test method precision statement after the development stage has been successfully completed. The data obtained in the interlaboratory study may indicate, however, that further effort is needed to improve the test method.  
1.3 Since the primary purpose of this practice is the development of the information needed for a precision statement, the experimental design in this practice may not be optimum for evaluating materials, apparatus, or individual laboratories.  
1.4 Field of Application—This practice is concerned exclusively with test methods which yield a single numerical figure as the test result, although the single figure may be the outcome of a calculation from a set of measurements.  
1.4.1 This practice ...

  • Standard
    23 pages
    English language
    sale 15% off
  • Standard
    23 pages
    English language
    sale 15% off
ASTM
ASTM E2282-14(2023)(Guide)
Standard Guide for Defining the Test Result of a Test Method

ABSTRACT
The purpose of this guide is to provide guidelines for identifying the elements that comprise the test result of a test method and to illustrate how these elements combine into the test result. It covers the types of measurement scales used for expressing observations and test results. This guide provides information on the construction of test results from more elemental measurements.
SIGNIFICANCE AND USE
4.1 All test methods have an output in the form of a test result. This guide provides information on the construction of test results from more elemental measurements.  
4.2 A well defined test result is necessary before any precision statements can be made about the test method.  
4.2.1 Form and Style for ASTM Standards,2 Section A21, requires that every test method shall contain a statement regarding its precision, preferably as a result of an interlaboratory test program. Reporting of such studies is described in Practice E177, which illustrates the development of test results from observations and test determinations.  
4.2.2 Precision statements for ASTM test methods are applicable to test results. They are not applicable to test determinations or observations, unless specifically and clearly indicated otherwise.
SCOPE
1.1 The purpose of this guide is to provide guidelines for identifying the elements that comprise the test result of a test method and to illustrate how these elements combine into the test result.  
1.2 Types of measurement scales used for expressing observations and test results are discussed.  
1.3 No system of units is specified in this standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6646-03(2022)(Test Method)
Standard Test Method for Determination of the Accelerated Hydrogen Sulfide Breakthrough Capacity of Granular and Pelletized Activated Carbon

SIGNIFICANCE AND USE
5.1 This method compares the performance of granular or pelletized activated carbons used in odor control applications, such as sewage treatment plants, pump stations, etc. The method determines the relative breakthrough performance of activated carbon for removing hydrogen sulfide from a humidified gas stream. Other organic contaminants present in field operations may affect the H2S breakthrough capacity of the carbon; these are not addressed by this test. This test does not simulate actual conditions encountered in an odor control application, and is therefore meant only to compare the hydrogen sulfide breakthrough capacities of different carbons under the conditions of the laboratory test.  
5.2 This test does not duplicate conditions that an adsorber would encounter in practical service. The mass transfer zone in the 23 cm column used in this test is proportionally much larger than that in the typical bed used in industrial applications. This difference favors a carbon that functions more rapidly for removal of H2S over a carbon with slower kinetics. Also, the 1 % H2S challenge gas concentration used here engenders a significant temperature rise in the carbon bed. This effect may also differentiate between carbons in a way that is not reflected in the conditions of practical service.  
5.3 This standard as written is applicable only to granular and pelletized activated carbons with mean particle diameters less than 2.5 mm. Application of this standard to activated carbons with mean particle diameters (MPD) greater than 2.5 mm will require a larger diameter adsorption column. The ratio of column inside diameter to MPD should be greater than 10 in order to avoid wall effects. In these cases it is suggested that bed superficial velocity and contact time be held invariant at the conditions specified in this standard (4.77 cm/s and 4.8 s). Although not covered by this standard, data obtained from these tests may be reported as in paragraph 12 along with additional ...
SCOPE
1.1 This test method is intended to evaluate the performance of virgin, newly impregnated or in-service, granular or pelletized activated carbon for the removal of hydrogen sulfide from an air stream, under the laboratory test conditions described herein. A humidified air stream containing 1 % (by volume) hydrogen sulfide is passed through a carbon bed until 50 ppm breakthrough of H2S is observed. The H2S adsorption capacity of the carbon per unit volume at 99.5 % removal efficiency (g H2S/cm3 carbon) is then calculated. This test is not necessarily applicable to non-carbon adsorptive materials.  
1.2 This standard as written is applicable only to granular and pelletized activated carbons with mean particle diameters (MPD) less than 2.5 mm. See paragraph 5.3 if activated carbons with larger MPDs are to be tested.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D7252-22(Test Method)
Standard Test Method for Polyurethane Raw Materials: Determination of Monomer and Isomers in Isocyanates

SIGNIFICANCE AND USE
5.1 This test method is used for research or for quality control to characterize isocyanates used in polyurethane products.
SCOPE
1.1 This test method determines the percent by weight of monomeric isomers and total monomer in crude or modified isocyanates. The test method is applicable to methylene di(phenylisocyanate) (MDI) and polymeric (methylene phenylisocyanate) (PMDI). (See Note 1.)  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5818-22(Practice)
Standard Practice for Exposure and Retrieval of Samples to Evaluate Installation Damage of Geosynthetics

SIGNIFICANCE AND USE
5.1 The ability to maintain design function (for example, reinforcement, separation, barrier, etc.) or design properties (for example, tensile strength, chemical resistance, etc.), or both, of a geosynthetic may be affected by damage to the physical structure of the geosynthetic due to the rigors of field installation. The effect of damage may be assessed by analyzing specimens cut from sample(s) retrieved after installation in a representative test section. Analysis may be performed with visual examination or laboratory testing of specimens from the control sample(s), and from the exhumed sample(s).  
5.2 A uniform practice for installing and retrieving representative sample(s) from a test section is needed to assess installation damage using project-specific or generally accepted, representative materials and procedures. Damage of a specific grade and type of geosynthetic under specific installation procedures may be assessed with sample(s) exhumed from a full-scale test section.
SCOPE
1.1 This practice covers standardized procedures for obtaining samples of geosynthetics from a test section for use in assessment of the effects of damage immediately after installation caused only by the installation techniques. The assessment may include physical testing. This practice is applicable to any geosynthetic except those installed between layers of aggregate or soil modified by a binder.
Note 1: The binder would inhibit the retrieval of the geosynthetic without inflicting further damage to the geosynthetic. Other practices may be suitable for retrieving geosynthetics used in these applications but are out of the scope of this practice.  
1.2 This practice is limited to full-scale test sections and does not address laboratory modeling of field conditions. This practice does not address which test method(s) to use for quantifying installation damage.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E2480-12(2022)(Practice)
Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method with Multi-Valued Measurands

SIGNIFICANCE AND USE
5.1 ASTM regulations require precision statements for all test methods in terms of repeatability and reproducibility. This practice may be used in obtaining the information needed to prepare a precision statement in accordance with Practice E177 and the “Blue Book.”
SCOPE
1.1 This practice describes the techniques for planning, conducting, and analyzing the results of an interlaboratory study (ILS) conducted for certain test methods within Committee E12.  
1.2 This practice does not concern itself with the development of the test method but rather with the gathering of the information needed for the precision and bias statement after the completion of development of the test method. The data obtained in the ILS may indicate, however, that further effort is needed to improve the test method.  
1.3 This practice is concerned exclusively with test methods that derive a multi-valued measurand, such as, but not limited to, spectral reflectance, transmittance function, tristimulus values, or RGB values. Variation in measurements of such multi-valued measurands are usually analyzed by reducing the data to a single-valued parameter, such as color difference, ΔE.  
1.4 This practice covers methods of dealing with the non-normal distribution of the variation of sets of color-differences. This is done so that the user may derive valid statistics from such non-normal distributions.  
1.5 This practice does not cover test methods, even in Committee E12, whose measurands are single-valued, or whose variations are known to be normally distributed. Task groups involved with such test methods are referred to Practice E691 which contains preferable methods of analyzing data with those properties.  
1.6 This practice is not intended to establish a method for estimating possible color-difference tolerances.  
1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D5819-22(Guide)
Standard Guide for Selecting Test Methods for Experimental Evaluation of Geosynthetic Durability

SIGNIFICANCE AND USE
5.1 Designers/specifiers of geosynthetics should evaluate geosynthetic durability as an integral part of the geosynthetic specification/selection process. This guide is intended to guide a designer/specifier through a systematic determination of degradation concerns based on the intended geosynthetic function or performance characteristic. This guide then provides a guide to select available test methods for experimentally evaluating geosynthetic durability and to identify areas where no suitable test exists.  
5.2 This guide does not address the evaluation of degradation resulting from manufacturing, handling, transporting, or installing the geosynthetic.
SCOPE
1.1 This guide covers a designer/specifier through a systematic determination of those factors of the appropriate application environment that may affect the post-construction service life of a geosynthetic. Subsequently, test methods are recommended to facilitate an experimental evaluation of the durability of geosynthetics in a specified environment so that the durability can be considered in the design process.  
1.2 This guide is not intended to address durability issues associated with the manufacturing, handling, transportation, or installation environments.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
  • Guide
    7 pages
    English language
    sale 15% off