ASTM B26/B26M-09
(Specification)Standard Specification for Aluminum-Alloy Sand Castings
Standard Specification for Aluminum-Alloy Sand Castings
ABSTRACT
This specification covers aluminum alloy sand castings except those that are for aerospace applications. The chemical compositions are determined in accordance with the specified suitable chemical and spectrochemical test methods. Addition of small amounts of modifiers and grain refining elements to the molten alloys from the remelting furnace is permitted before casting. Pure metals, recycled materials, and master alloys can also be used to make the alloys as long as the chemical composition can be analyzed and adjusted to conform to the requirements prior to pouring any casting. Castings should only be repaired using approved processes such as welding, impregnation, peening, blending, soldering, and so forth.
SCOPE
1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1.
1.2 This specification is not intended for aluminum-alloy sand castings used in aerospace applications.
1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. Unified Numbering System alloy designations are in accordance with Practice E 527.
1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B26/B26M – 09
Standard Specification for
1
Aluminum-Alloy Sand Castings
This standard is issued under the fixed designation B26/B26M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* B275 Practice for Codification of Certain Nonferrous Met-
2
als and Alloys, Cast and Wrought
1.1 This specification covers aluminum-alloy sand castings
B557 Test Methods for Tension Testing Wrought and Cast
designated as shown in Table 1.
Aluminum- and Magnesium-Alloy Products
1.2 This specification is not intended for aluminum-alloy
B557M TestMethodsforTensionTestingWroughtandCast
sand castings used in aerospace applications.
Aluminum- and Magnesium-Alloy Products (Metric)
1.3 Alloy and temper designations are in accordance with
B660 Practices for Packaging/Packing of Aluminum and
ANSI H35.1/H35.1M. Unified Numbering System alloy des-
Magnesium Products
ignations are in accordance with Practice E527.
B881 TerminologyRelatingtoAluminum-andMagnesium-
1.4 Unless the order specifies the “M” specification desig-
Alloy Products
nation, the material shall be furnished to the inch-pound units.
B917/B917M Practice for Heat Treatment of Aluminum-
1.5 For acceptance criteria for inclusion of new aluminum
Alloy Castings from All Processes
and aluminum alloys and their properties in this specification,
D3951 Practice for Commercial Packaging
see Annex A1 and Annex A2.
E29 Practice for Using Significant Digits in Test Data to
1.6 The values stated in either SI units or inch-pound units
Determine Conformance with Specifications
are to be regarded separately as standard. The values stated in
E34 Test Methods for ChemicalAnalysis ofAluminum and
each system may not be exact equivalents; therefore, each
Aluminum-Base Alloys
system shall be used independently of the other. Combining
E94 Guide for Radiographic Examination
values from the two systems may result in non-conformance
E155 Reference Radiographs for Inspection of Aluminum
with the standard.
and Magnesium Castings
1.7 This standard does not purport to address all of the
E165 PracticeforLiquidPenetrantExaminationforGeneral
safety concerns, if any, associated with its use. It is the
Industry
responsibility of the user of this standard to establish appro-
E527 Practice for Numbering Metals and Alloys in the
priate safety and health practices and determine the applica-
Unified Numbering System (UNS)
bility of regulatory limitations prior to use.
E607 Test Method for Atomic Emission Spectrometric
2. Referenced Documents
Analysis Aluminum Alloys by the Point to Plane Tech-
nique Nitrogen Atmosphere
2.1 The following documents of the issue in effect on date
E716 Practices for Sampling Aluminum and Aluminum
of material purchase form a part of this specification to the
Alloys for Spectrochemical Analysis
extent referenced herein:
3
E1251 Test Method for Analysis of Aluminum and Alumi-
2.2 ASTM Standards:
num Alloys by Atomic Emission Spectrometry
B179 Specification for Aluminum Alloys in Ingot and
IEEE/ASTM SI 10 Standard for Use of the International
Molten Forms for Castings from All Casting Processes
System of Units (SI): The Modern Metric System
4
2.3 AMS Standard:
1
This specification is under the jurisdiction of ASTM Committee B07 on Light AMS 2771 Heat Treatment of Aluminum Alloy Castings
5
Metals and Alloys and is the direct responsibility of Subcommittee B07.01 on
2.4 American National Standards:
Aluminum Alloy Ingots and Castings.
H35.1/H35.1(M) Alloy and Temper Designation System for
Current edition approved May 1, 2009. Published June 2009. Originally
Aluminum
approved in 1918. Last previous edition approved in 2005 as B26/B26M – 05. DOI:
10.1520/B0026_B0026M-09.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
cation SB-26/SB-26M in Section II of that Code.
3 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from Society of Automotive Engineers (SAE), 400 Commonwealth
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Dr., Warrendale, PA 15096-0001, http://www.sae.org.
5
Standards volume information, refer to the standard’s Document Summary page on Available from Aluminum Association, Inc., 1525 Wilson Blvd., Suite 600,
the ASTM website. Arlington, VA 22209, http://www.aluminum.org/bookstore.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B 26/B 26M–05 Designation: B26/B26M – 09
Standard Specification for
1
Aluminum-Alloy Sand Castings
This standard is issued under the fixed designation B26/B26M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1.
1.2 This specification is not intended for aluminum-alloy sand castings used in aerospace applications.
1.3 Alloy and temper designations are in accordance withANSI H35.1/H35.1M and H35.1M. Unified Numbering System alloy
designations are in accordance with Practice E 527E527.
1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see
Annex A1 and Annex A2.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein:
3
2.2 ASTM Standards:
B179 Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
B275 Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought
B557 Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
B557M Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric](Metric)
B660 Practices for Packaging/Packing of Aluminum and Magnesium Products
B881 Terminology Relating to Aluminum- and Magnesium-Alloy Products
B917/B917M Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes
D3951 Practice for Commercial Packaging
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum Base-Alloys
E88Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition Test
Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E94 Guide for Radiographic Examination
E155 Reference Radiographs for ExaminationInspection of Aluminum and Magnesium Castings
E165 Test Method for Liquid Penetrant Examination Practice for Liquid Penetrant Examination for General Industry
E527 Practice for Numbering Metals and Alloys (UNS) Practice for Numbering Metals and Alloys in the Unified Numbering
System (UNS)
E607 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
1
This specification is under the jurisdiction ofASTM Committee B07 on Light Metals andAlloys and is the direct responsibility of Subcommittee B07.01 onAluminum
Alloy Ingots and Castings.
Current edition approved Sept. 1, 2005. Published September 2005. Originally approved in 1918. Last previous edition approved in 2003 as B 26/B 26M–03.
Current edition approved May 1, 2009. Published June 2009. Originally approved in 1918. Last previous edition approved in 2005 as B26/B26M – 05. DOI:
10.1520/B0026_B0026M-09.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-26/SB-26M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United S
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B26/B26M–05 Designation: B 26/B 26M – 09
Standard Specification for
1
Aluminum-Alloy Sand Castings
This standard is issued under the fixed designation B 26/B 26M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers aluminum-alloy sand castings designated as shown in Table 1.
1.2 This specification is not intended for aluminum-alloy sand castings used in aerospace applications.
1.3 Alloy and temper designations are in accordance withANSI H35.1/H35.1M and H35.1M. Unified Numbering System alloy
designations are in accordance with Practice E 527.
1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.
1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see
Annex A1 and Annex A2.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2.1 The following documents of the issue in effect on date of material purchase form a part of this specification to the extent
referenced herein:
3
2.2 ASTM Standards:
B 179 Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
B 275 Practice for Codification of Certain Nonferrous Metals and Alloys, Cast and Wrought
B 557 Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
B 557M Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products [Metric](Metric)
B 660 Practices for Packaging/Packing of Aluminum and Magnesium Products
B 881 Terminology Relating to Aluminum- and Magnesium-Alloy Products
B 917/B 917M Practice for Heat Treatment of Aluminum-Alloy Castings from All Processes
D 3951 Practice for Commercial Packaging
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum Base-Alloys
E88Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition Test
Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E94 Guide for Radiographic Examination
E 155 Reference Radiographs for ExaminationInspection of Aluminum and Magnesium Castings
E 165 Test Method for Liquid Penetrant Examination
E 527 Practice for Numbering Metals and Alloys (UNS) Practice for Numbering Metals and Alloys in the Unified Numbering
System (UNS)
E 607 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane
1
This specification is under the jurisdiction ofASTM Committee B07 on Light Metals andAlloys and is the direct responsibility of Subcommittee B07.01 onAluminum
Alloy Ingots and Castings.
Current edition approved Sept.May 1, 2005.2009. Published September 2005.June 2009. Originally approved in 1918. Last previous edition approved in 20032005 as
B 26/B 26M – 035.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-26/SB-26M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
B 26/B 26M – 09
TABLE 1 Chemical Composition Limits
NOTE 1—When single units are shown, these indicate the maximum amounts permitted.
N
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.