ASTM D6809-02(2016)
(Guide)Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
SIGNIFICANCE AND USE
5.1 Quality Control and Quality Assurance practices are important for the optimum operation of testing laboratories using D16 methods for aromatic hydrocarbons and related materials. Quality procedure guidelines, like those described in this document or other suitably correct QA/QC-related reference, can be useful to optimally perform these methods.
SCOPE
1.1 This guide contains non-mandatory Quality Assurance/Quality Control (QA/QC) activities that may be referenced in standards maintained by ASTM Committee D16 on Aromatic Hydrocarbons and Related Materials.
1.2 This guide does not purport to address all of the issues that may be pertinent to an active QA/QC process.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6809 − 02 (Reapproved 2016)
Standard Guide for
Quality Control and Quality Assurance Procedures for
Aromatic Hydrocarbons and Related Materials
This standard is issued under the fixed designation D6809; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Juran’s Quality Control Handbook Fourth Edition (1988)
1.1 This guide contains non-mandatory Quality Assurance/
3. Terminology
Quality Control (QA/QC) activities that may be referenced in
3.1 Definitions:
standards maintained by ASTM Committee D16 on Aromatic
3.1.1 precision, n—the degree of agreement of repeated
Hydrocarbons and Related Materials.
measurement of the same property, expressed in terms of
1.2 This guide does not purport to address all of the issues
dispersion of test results about an arithmetical mean result
that may be pertinent to an active QA/QC process.
obtained by repetitive testing of a homogeneous sample under
1.3 This standard does not purport to address all of the specified conditions. The precision of a test method is ex-
pressed quantitatively as a standard deviation computed from
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- the results of a series of controlled determinations. D4790
priate safety and health practices and determine the applica-
3.1.2 quality assurance, n—thegeneralactivityofproviding
bility of regulatory requirements prior to use.
evidence needed to establish confidence that the quality func-
tion is being effectively performed; may include quality
2. Referenced Documents
planning, quality control, quality improvement, quality audit,
and reliability. Juran’s Quality Control Handbook
2.1 ASTM Standards:
D4790 Terminology ofAromatic Hydrocarbons and Related
3.1.3 quality control, n—the specific tools, skills, or tech-
Chemicals
niques through which the quality function is carried out, can be
E177 Practice for Use of the Terms Precision and Bias in
part of a control process, for example, product inspection.
ASTM Test Methods
Juran’s Quality Control Handbook
E691 Practice for Conducting an Interlaboratory Study to
4. Summary of Guide
Determine the Precision of a Test Method
4.1 This guide contains non-mandatory information to be
2.2 ASTM Document:
considered for reference in all ASTM Committee D16 stan-
MNL7 Manual on Presentation of Data Control Chart
dards on aromatic hydrocarbons and related materials. This
Analysis, 6th Edition, Section 3: Control Charts for
information is provided as a QA/QC system guide for D16
Individuals
standard users who do not have an active QA/QC process in
2.3 Other Documents:
their laboratory.
Western Electric Company, Inc. Statistical Quality Control
Handbook (1982)
5. Significance and Use
5.1 Quality Control and Quality Assurance practices are
important for the optimum operation of testing laboratories
This guide is under the jurisdiction of ASTM Committee D16 on Aromatic
using D16 methods for aromatic hydrocarbons and related
Hydrocarbons and Related Chemicals and is the direct responsibility of Subcom-
materials. Quality procedure guidelines, like those described in
mittee D16.06 on Statistics and Quality.
Current edition approved Nov. 1, 2016. Published November 2016. Originally
this document or other suitably correct QA/QC-related
approved in 2002. Last previous edition approved in 2012 as D6809 – 02 (2012).
reference, can be useful to optimally perform these methods.
DOI: 10.1520/D6809-02R16.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
6. Quality Procedure Guidelines
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
6.1 Statistical Control—To establish the statistical control
the ASTM website.
status of the testing process since the last valid calibration,
Available from ASTM International, 100 Barr Harbor Drive, West
Conshohocken, PA 19428-2959, www.astm.org.
4 5
Available from American Society for Quality (ASQ), 600 N. Plankinton Ave., Available from McGraw-Hill Education, Columbus, OH, 43218, http://
Milwaukee, WI 53203, http://www.asq.org. www.mheducation.com.
Copyright
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6809 − 02 (Reapproved 2012) D6809 − 02 (Reapproved 2016)
Standard Guide for
Quality Control and Quality Assurance Procedures for
Aromatic Hydrocarbons and Related Materials
This standard is issued under the fixed designation D6809; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This guide contains non-mandatory Quality Assurance/Quality Control (QA/QC) activities that may be referenced in
standards maintained by ASTM Committee D16 on Aromatic Hydrocarbons and Related Materials.
1.2 This guide does not purport to address all of the issues that may be pertinent to an active QA/QC process.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
requirements prior to use.
2. Referenced Documents
2.1 ASTM Standards:
D4790 Terminology of Aromatic Hydrocarbons and Related Chemicals
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
2.2 ASTM Document:
MNL7 Manual on Presentation of Data Control Chart Analysis, 6th Edition, Section 3: Control Charts for Individuals
2.3 Other Documents:
Western Electric Company, Inc. Statistical Quality Control Handbook (1982)
Juran’sJuran’s Quality Control Handbook Fourth Edition (1988)
3. Terminology
3.1 Definitions:
3.1.1 precision, n—the degree of agreement of repeated measurement of the same property, expressed in terms of dispersion of
test results about an arithmetical mean result obtained by repetitive testing of a homogeneous sample under specified conditions.
The precision of a test method is expressed quantitatively as a standard deviation computed from the results of a series of controlled
determinations. D4790
3.1.2 quality assurance, n—the general activity of providing evidence needed to establish confidence that the quality function
is being effectively performed; may include quality planning, quality control, quality improvement, quality audit, and reliability.
Juran’sJuran’s Quality Control Handbook
3.1.3 quality control, n—the specific tools, skills, or techniques through which the quality function is carried out, can be part
of a control process, for example, product inspection. Juran’sJuran’s Quality Control Handbook
4. Summary of Guide
4.1 This guide contains non-mandatory information to be considered for reference in all ASTM Committee D16 standards on
aromatic hydrocarbons and related materials. This information is provided as a QA/QC system guide for D16 standard users who
do not have an active QA/QC process in their laboratory.
This guide is under the jurisdiction of ASTM Committee D16 on Aromatic Hydrocarbons and Related Chemicals and is the direct responsibility of Subcommittee D16.06
on Statistics and Quality.
Current edition approved Jan. 1, 2012Nov. 1, 2016. Published January 2012November 2016. Originally approved in 2002. Last previous edition approved in 20072012
as D6809 – 02 (2007).02 (2012). DOI: 10.1520/D6809-02R12.10.1520/D6809-02R16.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
Available from ASTM International, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959, www.astm.org.
Available from American Society for Quality (ASQ), 600 N. Plankinton Ave., Milwaukee, WI 53203, http://www.asq.org.
Available from McGraw-Hill Inc, St. Louis, MO, http://www.mcgraw-hill.com.Education, Columbus, OH, 43218, http://www.mheducation.com.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D6809 − 02 (2016)
5. Significance and Use
5.1 Quality Control and Quality Assurance practices are important for the optimum operation of testing laboratories using D16
meth
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.