iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM A1092-15(2020)

(Specification)

Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet

Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet

ABSTRACT
This specification covers requirements for as cold-reduced, steel sheet in coils intended for conversion into cold-rolled steel sheet on continuous annealing lines, and metallic-coated steel sheet on continuous hot-dip coating lines. As cold-reduced steel sheet in coils comes in a semi-finished form and is produced to thickness requirements expressed to 0.001 in. (0.01 mm). Due to the high degree of cold reduction, as cold-reduced steel sheet exhibits high tensile strength with very minimal ductility.
This specification prescribes the requirements for chemical composition; mechanical properties; dimensions and mass; flatness, width, and coil size; product finish and condition; and packaging and marking.
SCOPE
1.1 This specification covers the requirements for as cold-reduced steel sheet in coils intended for conversion into cold-rolled steel sheet on continuous annealing lines, and metallic-coated steel sheet on continuous hot-dip coating lines.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
29-Feb-2020
ICS
77.140.50 - Flat steel products and semi-products
Technical Committee
A01 - Steel, Stainless Steel and Related Alloys
Drafting Committee
A01.19 - Steel Sheet and Strip
Current Stage
Ref Project

Relations

Replaces
ASTM A1092-15 - Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet
Effective Date
01-Mar-2020
Refers
ASTM A1008/A1008M-23 - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable
Effective Date
01-Nov-2023
Refers
ASTM A1008/A1008M-23e1 - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Required Hardness, Solution Hardened, and Bake Hardenable
Effective Date
01-Nov-2023
Refers
ASTM A568/A568M-19a - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Effective Date
01-Nov-2019
Refers
ASTM A1088-13(2019) - Standard Specification for Steel, Sheet, Cold-Rolled, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP)
Effective Date
01-Nov-2019
Refers
ASTM A1008/A1008M-18 - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
Effective Date
01-Sep-2018
Refers
ASTM A568/A568M-17a - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Effective Date
01-Nov-2017
Refers
ASTM A568/A568M-17 - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Effective Date
01-Sep-2017
Refers
ASTM A1008/A1008M-16 - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
Effective Date
01-Sep-2016
Refers
ASTM A568/A568M-15 - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Effective Date
01-Nov-2015
Refers
ASTM A1008/A1008M-15 - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
Effective Date
01-May-2015
Refers
ASTM A1088-13 - Standard Specification for Steel, Sheet, Cold-Rolled, Complex Phase (CP), Dual Phase (DP) and Transformation Induced Plasticity (TRIP)
Effective Date
01-Nov-2013
Refers
ASTM A568/A568M-13a - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Effective Date
01-Oct-2013
Refers
ASTM A1008/A1008M-13 - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, Solution Hardened, and Bake Hardenable
Effective Date
01-Oct-2013
Refers
ASTM A568/A568M-13ae1 - Standard Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
Effective Date
01-Oct-2013

Buy Standard

ASTM A1092-15(2020) - Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel SheetASTM A1092-15(2020) - Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet
PreviousNext
Technical specification
ASTM A1092-15(2020) - Standard Specification for Steel Sheet, as Cold-Reduced, for Conversion to Annealed Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel Sheet
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: A1092 −15 (Reapproved 2020)
Standard Specification for
Steel Sheet, as Cold-Reduced, for Conversion to Annealed
Cold-Rolled Steel Sheet, and Hot Dip Metallic-Coated Steel
Sheet
This standard is issued under the fixed designation A1092; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
A875/A875M Specification for Steel Sheet, Zinc-5 % Alu-
1.1 This specification covers the requirements for as cold-
minum Alloy-Coated by the Hot-Dip Process
reduced steel sheet in coils intended for conversion into
A924/A924M Specification for General Requirements for
cold-rolled steel sheet on continuous annealing lines, and
Steel Sheet, Metallic-Coated by the Hot-Dip Process
metallic-coated steel sheet on continuous hot-dip coating lines.
A929/A929M Specification for Steel Sheet, Metallic-Coated
1.2 The values stated in inch-pound units are to be regarded
by the Hot-Dip Process for Corrugated Steel Pipe
as standard. The values given in parentheses are mathematical
A1008/A1008M Specification for Steel, Sheet, Cold-Rolled,
conversions to SI units that are provided for information only
Carbon, Structural, High-Strength Low-Alloy, High-
and are not considered standard.
Strength Low-Alloy with Improved Formability, Solution
1.3 This international standard was developed in accor-
Hardened, and Bake Hardenable
dance with internationally recognized principles on standard- A1046/A1046M Specification for Steel Sheet, Zinc-
ization established in the Decision on Principles for the
Aluminum-MagnesiumAlloy-Coated by the Hot-Dip Pro-
Development of International Standards, Guides and Recom- cess
mendations issued by the World Trade Organization Technical
A1063/A1063M Specification for Steel Sheet, Twin-Roll
Barriers to Trade (TBT) Committee. Cast, Zinc-Coated (Galvanized) by the Hot-Dip Process
A1079 Specification for Steel Sheet, Complex Phase (CP),
2. Referenced Documents
Dual Phase (DP) and Transformation Induced Plasticity
(TRIP), Zinc-Coated (Galvanized) or Zinc-Iron Alloy-
2.1 ASTM Standards:
Coated (Galvannealed) by the Hot-Dip Process
A308/A308M Specification for Steel Sheet, Terne (Lead-Tin
A1088 Specification for Steel, Sheet, Cold-Rolled, Com-
Alloy) Coated by the Hot-Dip Process (Withdrawn 2015)
plex Phase (CP), Dual Phase (DP) and Transformation
A463/A463M Specification for Steel Sheet, Aluminum-
Induced Plasticity (TRIP)
Coated, by the Hot-Dip Process
A568/A568M Specification for Steel, Sheet, Carbon,
3. Terminology
Structural,andHigh-Strength,Low-Alloy,Hot-Rolledand
Cold-Rolled, General Requirements for
3.1 Definitions:
A653/A653M Specification for Steel Sheet, Zinc-Coated
3.1.1 as cold-reduced steel sheet, n—an as-rolled product
(Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed)
intended for conversion to annealed cold-rolled steel sheet
by the Hot-Dip Process
product or hot-dip metallic-coated steel sheet product.
A792/A792M Specification for Steel Sheet, 55 %
3.1.1.1 Discussion—As a result of the high degree of cold
reduction as cold-reduced steel sheet exhibits high tensile
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
strength with very minimal ductility.
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.19 on Steel Sheet and Strip.
4. Classification
Current edition approved March 1, 2020. Published March 2020. Originally
approved in 2015. Last previous edition approved in 2015 as A1092 – 15. DOI:
4.1 The material is in a semi-finished form intended for
10.1520/A1092-15R20
conversiontocold-rolledsteelsheet,orhot-dipmetallic-coated
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
sheet steel whose designations are described in the following
Standards volume information, refer to the standard’s Document Summary page on
specifications:
the ASTM website.
4.1.1 A308/A308M Specification for Steel Sheet, Terne
The last approved version of this historical standard is referenced on
www.astm.org. (Lead-Tin Alloy) Coated by the Hot-Dip Process,
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
A1092 − 15 (2020)
4.1.2 A463/A463M Specification for Steel Sheet, 5.4 Special requirements (if any).
Aluminum-Coated, by the Hot-Dip Process,
5.4.1 When the purchaser requires the thickness tolerances
4.1.3 A653/A653M Specification for Steel Sheet, Zinc-
for ⁄8 in. minimum edge distance this requirement shall be
Coated (Galvanized) or Zinc-Iron Alloy-Coated (Gal-
specified on the purchase order or contract (see Specifications
vannealed) by the Hot-Dip Process,
A568/A568M or A924/A924M, as applicable).
4.1.4 A792/A792M Specification for Steel Sheet, 55%
Aluminum-Zinc Alloy-Coated by the Hot-Dip Process,
6. Chemical Composition
4.1.5 A875/A875M Specification for Steel Sheet, Zinc-5 %
6.1 The chemical composition shall conform to the require-
Aluminum Alloy-Coated by the Hot-Dip Process,
ments of the intended designation in the individual metallic-
4.1.6 A929/A929M Specification for Steel Sheet, Metallic-
coated sheet and cold-rolled specification to which the product
Coated by the Hot-Dip Process for Corrugated Steel Pipe,
will be converted, namely Specifications A308/A308M, A463/
4.1.7 A1008/A1008M Specification for Steel, Sheet, Cold-
A463M, A653/A653M, A792/A792M, A875/A875M, A929/
Rolled, Carbon, Structural, High-Strength Low-Alloy, High-
A929M, A1008/A1008M, A1046/A1046M, A1063/A1063M,
Strength Low-Alloy with Improved Formability, Solution
A1079,or A1088.
Hardened, and Bake Hardenable,
4.1.8 A1046/A1046M Specification for Steel Sheet, Zinc- 6.2 See Specification A568/A568M for chemical analysis
procedures for cold-rolled product, and Specification A924/
Aluminum-Magnesium Alloy-Coated by the Hot-Dip Pr
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM A950/A950M-24(Specification)
Standard Specification for Fusion-Bonded Epoxy-Coated Structural Steel H-Piles and Sheet Piling

ABSTRACT
This specification covers the qualification requirements for structural steel H-piles and sheet piling with protective fusion-bonded epoxy coating applied by electrostatic spraying, flocking, or fluidized bed processing. Surface preparation techniques shall be performed by abrasive blast cleaning, grinding and chemical washing prior to coating application. The powder coating shall be heat treated and cured before visible oxidation occurs. Coating materials shall undergo thickness measurements and bend testing, and shall conform to the requirements for film thickness, flexibility and continuity, impact resistance, chemical composition, and corrosion resistance. The coated H-piles or sheet piling shall be stored off of the ground on supports. While handling equipment, bundling bands for packaging and tie-down bands for shipping shall have padded contact areas so as to avoid damage and excessive deflection.
SCOPE
1.1 This specification covers structural steel H-piles and sheet piling with protective fusion-bonded epoxy coating applied by the electrostatic spray, flocking, or fluidized bed process.  
Note 1: The coating applicator is identified throughout this specification as the manufacturer.  
1.2 Requirements for coatings are contained in Annex A1.  
1.3 This specification is applicable for orders in either inch-pound units (as Specification A950) or SI units (as Specification A950M). The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off
ASTM
ASTM A830/A830M-24(Specification)
Standard Specification for Plates, Carbon Steel, Structural Quality, Furnished to Chemical Composition Requirements

ABSTRACT
This specification covers structural quality carbon steel plates in standard and non-standard grades furnished to chemical composition requirements. The materials shall conform to carbon, manganese, phosphorus, sulfur, silicon, and copper contents of its specified grade. Values are also given to specify the range, limit, and maximum chemical compositions of the carbon steel.
SCOPE
1.1 This specification covers structural quality carbon steel plates furnished to chemical composition requirements.  
1.2 The plates are available in several standard steel grades and non-standard grades.  
1.3 The plates are usually furnished in the as-rolled (hot-rolled) condition.  
1.4 Supplementary requirements are provided for additional requirements that may be specified on the order.  
1.5 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.  
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM A656/A656M-24(Specification)
Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability

ABSTRACT
This specification covers the three types and four strength grades of high strength low-alloy, hot rolled structural steel plate with improved formability. These steels are normally furnished in the as-rolled condition. For plates produced from coil, and furnished without heat treatment or with stress relieving only, additional testing requirements and the reporting of additional test results, of a reference material shall apply. Chemical composition requirements shall be dependent upon thickness, grade, and intended applications. Tension tests shall be executed to evaluate conformance of specimens with specified mechanical properties requirements.
SCOPE
1.1 This specification covers three types and five strength grades of high-strength low-alloy, hot-rolled structural steel plate for use in truck frames, brackets, crane booms, rail cars, and similar applications. Steels that conform to this specification offer improved formability. These steels are normally furnished in the as-rolled condition. The type and strength grade furnished is as agreed upon between the manufacturer and the purchaser. The types and strength grades are shown in the tables.  
1.2 The maximum thickness of plates shall be as follows:    
Grade  
Plate Thickness, max,
in. [mm]  
50  
2 [50]  
60  
11/2 [40]  
70  
1 [25]  
80  
1 [25]  
100  
1/2 [13]  
1.3 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A109/A109M-24(Specification)
Standard Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled

ABSTRACT
This specification covers cold-rolled carbon steel strip in cut lengths or coils, furnished to closer tolerances than cold-rolled carbon steel sheet. The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace process. Cold-rolled carbon strip specified to temper numbers shall conform to the Rockwell hardness requirements. Bend tests shall be conducted in accordance with requirements specified.
SCOPE
1.1 This specification covers cold-rolled carbon steel strip in cut lengths or coils, furnished to closer tolerances than cold-rolled carbon steel sheet, with specific temper, with specific edge or specific finish, and in sizes as follows:    
Width, in.  
Thickness, in.    
Over 1/2 to 23 15/16  
0.300 and under    
Over 12.5 to 600 mm  
7.6 mm and under  
1.2 Cold-rolled strip is produced with a maximum specified carbon not exceeding 0.25 percent.  
1.3 Strip tolerance products may be available in widths wider than 23 15/16 in. [600 mm] by agreement between purchaser and supplier. However, such products are technically classified as cold rolled sheet. The tolerances, finishes, tempers, edges, and available widths and thicknesses differentiate cold rolled strip from the product known as cold rolled sheet which is defined by Specification A568/A568M and from cold rolled high carbon strip which is defined by Specification A682/A682M.  
1.4 For the purpose of determining conformance with this specification, values shall be rounded to the nearest unit in the right hand place of figures used in expressing the limiting values in accordance with the rounding method of Practice E29.  
1.5 The SI portions of the tables contained herein list permissible variations in dimensions and mass (see Note 1) in SI (metric) units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to SI tolerances is mandatory when the “M” specification is used.
Note 1: The term weight is used when inch-pound units are the standard. However, under SI the preferred term is  mass.  
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.7 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM A625/A625M-13(2024)(Specification)
Standard Specification for Tin Mill Products, Black Plate, Single-Reduced

ABSTRACT
This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications. The black plates shall be produced with ground roll and shot-blasted roll finishes and shall be furnished oiled or dry.
SCOPE
1.1 This specification covers single-reduced black plate produced from low carbon, cold-reduced steel, furnished in coils and cut sizes, for use in the manufacture of containers, closures, signs, toys and other products, as well as for plating applications.  
1.2 It may be supplied dry or oiled and with or without surface treatment. This product is normally supplied with a trimmed edge.  
1.3 This specification is applicable to orders in either inch-pound units (as A625), which is supplied in thicknesses from 135-lb base weight (0.0149 in.) and lighter, or SI units (as A625M), which is supplied in thicknesses from 0.378 mm and lighter.  
1.4 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A666/A666M-24(Specification)
Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar

ABSTRACT
This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions. They shall be formed in different shapes such as sheets, strips, plates and flat bars. The steels shall adhere to specified chemical composition requirements. Mechanical properties such as yield strength, tensile strength, elongation, hardness, and bending shall be determined. The specimens shall be subjected to tension test, free-bend test, and controlled-bend or V-block test.
SCOPE
1.1 This specification covers austenitic stainless steels in the annealed and normally required cold-worked conditions for various structural, pressure vessel, magnetic, cryogenic, and heat-resisting applications.  
1.2 The application of this specification, or the use of material covered by this specification does not automatically allow usage in pressure vessel applications. Only annealed conditions of grades specifically approved by the ASME code are permitted for pressure vessel use.  
1.3 This specification is expressed in both inch-pound units and in SI units; however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM A650/A650M-18(2024)(Specification)
Standard Specification for Tin Mill Products, Black Plate, Double Reduced

ABSTRACT
This specification covers doubled-reduced black plate tin mill products produced from low-carbon cold-reduced steel, furnished in coils and cut sizes, for use predominantly in the manufacture of containers. The product, which is normally supplied with trimmed edges, may be specified "as rolled," without the removal of the rolling solution, and with no additional surface or oiling treatment, or "cleaned" with the rolling solution removed, with or without surface treatment and oiling. The rolling direction must be specified on cut lengths and will be indicated by underlining the slit (rolling width) dimension. Surfaces may polished in either the ground roll finish (base metal finish), or smooth finish with grit lines (7C finish).
SCOPE
1.1 This specification covers double-reduced black plate, produced from low-carbon cold-reduced steel, furnished in coils and cut sizes, for use predominantly in the manufacture of containers. The product may be specified “as rolled,” without the removal of the rolling solution, and with no additional surface or oiling treatment. It may also be specified “cleaned” with the rolling solution removed, with or without surface treatment and oiling. This product is normally supplied with trimmed edges.  
1.2 This specification is applicable to orders in either inch-pound units (as A650) which is supplied in thicknesses 0.0050 in. to 0.0113 in. or SI units [as A650M] which is supplied in thicknesses from 0.127 to 0.287 mm.  
1.3 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM A657/A657M-18(2024)(Specification)
Standard Specification for Tin Mill Products, Black Plate Electrolytic Chromium-Coated, Single and Double Reduced

ABSTRACT
This specification covers single- and double-reduced tin mill black plate electrolytically coated with chromium and chromium oxide. The steel shall be furnished in coils and cut lengths for use in manufacture of cans, closures, crowns, and other products. The weights of the total coating which is made up of chromium metal and chromium oxides shall be determined. Single-reduced base steels shall be produced with ground roll finishes (type 7B-A for smooth finish containing fine grit lines and type 7C-A for smooth finish with grit lines), and shot-blasted and/or textured roll finishes (type 5C-A for shot-blasted finish for general applications and type 5D-A for special applications). Double-reduced base steels shall be produced only with ground roll finishes of type 7C-A. The steels shall be furnished with extremely thin oil film on both surfaces.
SCOPE
1.1 This specification covers single- and double-reduced tin mill black plate electrolytically coated with chromium and chromium oxide. The steel is furnished in coils and cut lengths for use in the manufacture of cans, closures, crowns, and other products.  
1.2 This specification is applicable to orders in either inch-pound units (as A657) which is supplied in thicknesses from 0.0050 to 0.0149 in. or in SI units [as A657M] which is supplied in thicknesses from 0.127 to 0.378 mm.  
1.3 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents. Therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM A283/A283M-24(Specification)
Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates

ABSTRACT
This specification covers four grades of carbon steel plates of structural quality for general application. Steel samples shall be melt processed by either open-hearth, basic-oxygen, or electric furnace. Heat and product analysis shall be performed wherein steel materials shall conform to required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, and copper. Steel specimens shall also undergo tensile tests and shall conform to required values of tensile strength, yield point, and elongation.
SCOPE
1.1 This specification2 covers two grades (C and D) of carbon steel plates of structural quality for general application.  
1.2 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.  
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 For plate produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.  
1.5 This specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A1034/A1034M-24(Specification)
Standard Specification for Mechanical Splices for Steel Reinforcing Bars

SIGNIFICANCE AND USE
5.1 Significance:  
5.1.1 The bar-splice assembly test specimen shall closely represent the mechanical splice used in practice. The behavior of the bar-splice assembly embedded in concrete, however, may differ from its behavior during testing where it is not embedded in concrete.  
5.2 Usefulness:  
5.2.1 Testing of mechanical splices for reinforcing bars shall establish the behavior of the bar-splice assembly under the loading conditions described herein for the various test methods to determine the acceptability of the mechanical splice for use in reinforced concrete structural members under specific design criteria.  
5.3 Interpretation of Test Results:  
5.3.1 Similar or better performance of mechanical splices installed in structural members shall be expected only if materials and methods of assembly are similar to the materials and methods used in the tests.
SCOPE
1.1 General—This specification covers the qualification requirements and test methods of mechanical splices for reinforcing bars. Qualification requirements are located in Annex A1. The various tests herein described can be specified in total or individually.  
1.2 The test methods herein described are applicable to any type of mechanical splice manufactured to join steel reinforcing bars of any grade (specified minimum yield strength), uncoated or coated.
Note 1: Various code-writing bodies specify various parameters, such as test loads, number of cycles and test temperature, for testing.  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off