iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E72-14

(Test Method)

Standard Test Methods of Conducting Strength Tests of Panels for Building Construction

Standard Test Methods of Conducting Strength Tests of Panels for Building Construction

SIGNIFICANCE AND USE
8.1 The procedures described are those that will test the behavior of segments of wall construction under conditions representative of those encountered in service. Performance criteria based on data from those procedures can ensure structural adequacy and service life.
SCOPE
1.1 These test methods cover the following procedures for determining the structural properties of segments of wall, floor, and roof constructions:    
Section  
Test Specimens  
3  
Loading  
4  
Deformation Measurements  
5  
Reports  
6  
Precision and Accuracy  
7  
TESTING WALLS  
Significance and Use  
8  
Compressive Load  
9  
Tensile Load  
10  
Transverse Load—Specimen Horizontal  
11  
Transverse Load—Specimen Vertical  
12  
Concentrated Load  
13  
Impact Load—See Test Methods E695 and E661  
Racking Load—Evaluation of Sheathing Materials
on a Standard Wood Frame  
14  
Racking Load—Evaluation of Sheathing Materials (Wet)
on a Standard Wood Frame  
15  
TESTING FLOORS  
Significance and Use  
16  
Transverse Load  
17  
Concentrated Load  
18  
Impact Load—See Test Methods E695 and E661  
TESTING ROOFS  
Section  
Significance and Use  
19  
Transverse Load  
20  
Concentrated Load  
21  
APPENDIX  
Technical Interpretation  
Appendix X1  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.2.1 Exception—SI units are used in Fig. 6.

General Information

Status
Historical
Publication Date
31-May-2014
ICS
91.060.10 - Walls. Partitions. Facades
Technical Committee
E06 - Performance of Buildings
Drafting Committee
E06.11 - Horizontal and Vertical Structures/Structural Performance of Completed Structures
Current Stage
Ref Project

Relations

Replaces
ASTM E72-13a - Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
Effective Date
01-Jun-2014
Replaced By
ASTM E72-14a - Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
Effective Date
01-Jul-2014
Referred By
ASTM E2322-22 - Standard Test Method for Conducting Transverse and Concentrated Load Tests on Panels used in Floor and Roof Construction
Effective Date
01-Jun-2014
Referred By
ASTM D2394-17(2022) - Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring
Effective Date
01-Jun-2014
Referred By
ASTM E2969-18 - Standard Test Methods for Transverse Load Tests on Panels Used in Wall Construction
Effective Date
01-Jun-2014
Referred By
ASTM C956-04(2019) - Standard Specification for Installation of Cast-In-Place Reinforced Gypsum Concrete
Effective Date
01-Jun-2014
Referred By
ASTM E2570/E2570M-07(2019) - Standard Test Methods for Evaluating Water-Resistive Barrier (WRB) Coatings Used under Exterior Insulation and Finish Systems (EIFS) or EIFS with Drainage
Effective Date
01-Jun-2014
Referred By
ASTM F3459-21 - Standard Specification for Rigid Poly Vinyl Chloride (PVC) Exterior Profiles Used for Sound Walls
Effective Date
01-Jun-2014
Referred By
ASTM C887-20 - Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar
Effective Date
01-Jun-2014
Referred By
ASTM C90-22 - Standard Specification for Loadbearing Concrete Masonry Units
Effective Date
01-Jun-2014
Referred By
ASTM E1803-14(2022) - Standard Test Methods for Determining Strength Capacities of Structural Insulated Panels
Effective Date
01-Jun-2014
Referred By
ASTM D3841-21 - Standard Specification for Glass-Fiber-Reinforced Polyester Plastic Panels
Effective Date
01-Jun-2014
Referred By
ASTM E2126-19 - Standard Test Methods for Cyclic (Reversed) Load Test for Shear Resistance of Vertical Elements of the Lateral Force Resisting Systems for Buildings
Effective Date
01-Jun-2014
Referred By
ASTM C1852-20 - Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives
Effective Date
01-Jun-2014
Referred By
ASTM C208-22 - Standard Specification for Cellulosic Fiber Insulating Board
Effective Date
01-Jun-2014

Buy Standard

ASTM E72-14 - Standard Test Methods of Conducting Strength Tests of Panels for Building ConstructionASTM E72-14 - Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
PreviousNext
Standard
ASTM E72-14 - Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM E72-14 - Standard Test Methods of Conducting Strength Tests of Panels for Building ConstructionREDLINE ASTM E72-14 - Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
PreviousNext
Standard
REDLINE ASTM E72-14 - Standard Test Methods of Conducting Strength Tests of Panels for Building Construction
English language
13 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E72 − 14
StandardTest Methods of
Conducting Strength Tests of Panels for Building
1
Construction
This standard is issued under the fixed designation E72; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
INTRODUCTION
Sound engineering design of structures using existing or new materials requires accurate technical
data on the strength and rigidity of the basic elements employed in various construction systems. It is
the purpose of these test methods to provide a systematic basis for obtaining engineering data on
various construction elements and structural details of value to designers, builders, building officials,
and others interested in this field. The results should closely approximate the performance in actual
service.
1. Scope
Concentrated Load 21
APPENDIX
1.1 These test methods cover the following procedures for
Technical Interpretation Appendix X1
determining the structural properties of segments of wall, floor,
1.2 The values stated in inch-pound units are to be regarded
and roof constructions:
as standard. The values given in parentheses are mathematical
Section
conversions to SI units that are provided for information only
Test Specimens 3
and are not considered standard.
Loading 4
Deformation Measurements 5 1.2.1 Exception—SI units are used in Fig. 6.
Reports 6
Precision and Accuracy 7
2. Referenced Documents
TESTING WALLS
Significance and Use 8 2
2.1 ASTM Standards:
Compressive Load 9
D2395 TestMethodsforDensityandSpecificGravity(Rela-
Tensile Load 10
Transverse Load—Specimen Horizontal 11
tive Density) of Wood and Wood-Based Materials
Transverse Load—Specimen Vertical 12
D4442 Test Methods for Direct Moisture Content Measure-
Concentrated Load 13
ment of Wood and Wood-Base Materials
Impact Load—See Test Methods E695 and E661
Racking Load—Evaluation of Sheathing Materials 14
D7438 Practice for Field Calibration and Application of
on a Standard Wood Frame
Hand-Held Moisture Meters
Racking Load—Evaluation of Sheathing Materials (Wet) 15
E4 Practices for Force Verification of Testing Machines
on a Standard Wood Frame
TESTING FLOORS
E73 Practice for Static Load Testing of Truss Assemblies
Significance and Use 16
E564 Practice for Static Load Test for Shear Resistance of
Transverse Load 17
Framed Walls for Buildings
Concentrated Load 18
Impact Load—See Test Methods E695 and E661
E575 Practice for Reporting Data from Structural Tests of
TESTING ROOFS
Building Constructions, Elements, Connections, and As-
Section
Significance and Use 19 semblies
Transverse Load 20
E661 Test Method for Performance of Wood and Wood-
Based Floor and Roof Sheathing Under Concentrated
Static and Impact Loads
1
These test methods are under the jurisdiction of ASTM Committee E06 on
Performance of Buildings and are the direct responsibility of Subcommittee E06.11
on Horizontal and Vertical Structures/Structural Performance of Completed Struc-
2
tures. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 1, 2014. Published August 2014. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1947. Last previous edition approved in 2013 as E72 – 13a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/E0072-14. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E72−14
E695 Test Method of Measuring Relative Resistance of with no load on the specimen or under a small initial load.
Wall, Floor, and Roof Construction to Impact Loading Increase the load to the first increment and record the defor-
E2126 Test Methods for Cyclic (Reversed) Load Test for mation. Unless otherwise specified, decrease the load to the
Shear Resistance ofVertical Elements of the Lateral Force initial load and record the set (sometimes designated “perma-
Resisting Systems for Buildings nent set”). Increase the load to two increments and record the
E2309/E2309M Practices for Verification of Displacement set, when it is released to the initial load. Follow this sequence
Measuring Systems and Devices Used in Material Testing of readings for three increments, four increments, and so forth,
Machines of load. When for each specimen the behavior of the specimen
E2322 Test Method for Conducting Transverse and Concen- under load indicates that the specimen might fail suddenly and
trated Load Tests on Panels
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E72 − 13a E72 − 14
Standard Test Methods of
Conducting Strength Tests of Panels for Building
1
Construction
This standard is issued under the fixed designation E72; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
INTRODUCTION
Sound engineering design of structures using existing or new materials requires accurate technical
data on the strength and rigidity of the basic elements employed in various construction systems. It is
the purpose of these test methods to provide a systematic basis for obtaining engineering data on
various construction elements and structural details of value to designers, builders, building officials,
and others interested in this field. The results should closely approximate the performance in actual
service.
1. Scope
1.1 These test methods cover the following procedures for determining the structural properties of segments of wall, floor, and
roof constructions:
Section
Test Specimens 3
Loading 4
Deformation Measurements 5
Reports 6
Precision and Accuracy 7
TESTING WALLS
Significance and Use 8
Compressive Load 9
Tensile Load 10
Transverse Load—Specimen Horizontal 11
Transverse Load—Specimen Vertical 12
Concentrated Load 13
Impact Load—See Test Methods E695 and E661
Racking Load—Evaluation of Sheathing Materials 14
on a Standard Wood Frame
Racking Load—Evaluation of Sheathing Materials (Wet) 15
on a Standard Wood Frame
TESTING FLOORS
Significance and Use 16
Transverse Load 17
Concentrated Load 18
Impact Load—See Test Methods E695 and E661
TESTING ROOFS
Section
Significance and Use 19
Transverse Load 20
Concentrated Load 21
APPENDIX
Technical Interpretation Appendix X1
Section
Test Specimens 3
Loading 4
1
These test methods are under the jurisdiction of ASTM Committee E06 on Performance of Buildings and are the direct responsibility of Subcommittee E06.11 on
Horizontal and Vertical Structures/Structural Performance of Completed Structures.
Current edition approved Nov. 1, 2013June 1, 2014. Published December 2013August 2014. Originally approved in 1947. Last previous edition approved in 2013 as
E72 – 13.E72 – 13a. DOI: 10.1520/E0072-13A.10.1520/E0072-14.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E72 − 14
Deformation Measurements 5
Reports 6
Precision and Accuracy 7
TESTING WALLS
Significance and Use 8
Compressive Load 9
Tensile Load 10
Transverse Load—Specimen Horizontal 11
Transverse Load—Specimen Vertical 12
Concentrated Load 13
Impact Load—See Test Methods E695 and
E661
Racking Load—Evaluation of Sheathing 14
Materials on a Standard Wood Frame
Racking Load—Evaluation of Sheathing 15
Materials (Wet) on a Standard Wood
Frame
TESTING FLOORS
Significance and Use 16
Transverse Load 17
Concentrated Load 18
Impact Load—See Test Methods E695 and
E661
TESTING ROOFS
Section
Significance and Use 19
Transverse Load 20
Concentrated Load 21
APPENDIX
Technical Interpretation Appendix X1
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.2.1 Exception—SI units are used in Fig. 6.
2. Referenced Documents
2
2.1 ASTM Standards:
D2395 Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials
D4442 Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
D7438 Practice for Field Calibration and Application of Hand-Held Moisture Meters
E4 Practices for Force Verification of Testing Machines
E73 Practice for Static Load Testing of Truss Assemblies
E564 Practice for Static Load Test for Shear Resistance of Framed Walls for Buildings
E575 Practice for Reporting Data from Structural Tests of Building Constructions, Elements, Connections, and Assemblies
E661 Test Method for Performance of Wood and Wood-Based Floor and Roof Sheathing Under Concentrated Static and Impact
Loads
E695 Test Method of Measuring Relative Resistance of Wall, Floor, and Roof Construction to Impact Loading
E2126 Test Methods for Cyclic (Reversed) Load Test for Shear Resistance of Vertical Elements o
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E1996-23(Specification)
Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

ABSTRACT
This specification covers exterior windows, glazed curtain walls, doors and impact protective systems used in buildings located in geographic regions that are prone to hurricanes. The test specimens shall be Fenestration assemblies, and impact protective systems; which shall be tested using the large missile test, and small missile test. The air pressure cycling, missiles, and impact location are also detailed.
SCOPE
1.1 This specification covers exterior windows, glazed curtain walls, doors, and impact protective systems used in buildings located in geographic regions that are prone to hurricanes.  
1.1.1 Exception—Exterior garage doors and rolling doors are governed by ANSI/DASMA 115 and are beyond the scope of this specification.  
1.2 This specification provides the information required to conduct Test Method E1886.  
1.3 Qualification under this specification provides a basis for judgment of the ability of applicable elements of the building envelope to remain unbreached during a hurricane; thereby minimizing the damaging effects of hurricanes on the building interior and reducing the magnitude of internal pressurization. While this standard was developed for hurricanes, it may be used for other types of similar windstorms capable of generating windborne debris.  
1.4 This specification provides a uniform set of guidelines based upon currently available information and research.2 As new information and research becomes available it will be considered.  
1.5 All values are stated in SI units and are to be regarded as standard. Values given in parentheses are for information only. Where certain values contained in reference documents cited and quoted herein are stated in inch-pound units, they must be converted by the user.  
1.6 The following precautionary statement pertains only to the test method portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    15 pages
    English language
    sale 15% off
  • Technical specification
    15 pages
    English language
    sale 15% off
ASTM
ASTM E2511-17(2023)(Guide)
Standard Guide for Detailing of EIFS-Clad Barrier and Drainage Wall Assemblies

SIGNIFICANCE AND USE
4.1 This guide is for use by individuals and entities involved with the design and specification of EIFS details for a specific building.  
4.2 This guide can be applied to both EIFS-clad barrier wall assembly and EIFS-clad wall with drainage.  
4.3 This guide can be applied to new and existing EIFS buildings, prefabricated versus on-site installed EIFS, and residential and commercial EIFS buildings.  
4.4 This guide is not meant to replace the types of information normally present in text format in a project’s specifications.  
4.5 This guide is not applicable to EIFS materials used in non EIFS applications, such as a topcoat for other base materials like traditional Portland cement plaster (stucco) and concrete.
SCOPE
1.1 This guide describes the types of project-specific construction conditions that need to be communicated by means of drawings (“details”) for the purpose of constructing Exterior Insulation and Finish System (EIFS)-clad barrier and drainage wall assemblies. EIFS manufacturers provide basic details for the installation of their materials and interface with adjacent materials. These details are generic and, in many cases, do not apply to specific project conditions.  
1.2 This guide addresses only the EIFS itself and the interface between the EIFS and the materials immediately adjacent to the EIFS; it does not address all parts of the wall assembly.  
1.3 Not all possible construction detail conditions are addressed by this guide. Identify and provide details for all construction conditions that exist on a specific building.  
1.4 This guide is intended to supplement but not supersede information from the EIFS manufacturer about how their specific product should be detailed, nor to supersede technical product acceptance reports or the code requirements of regulatory authorities.  
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM E331-00(2023)(Test Method)
Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference

SIGNIFICANCE AND USE
5.1 This test method is a standard procedure for determining the resistance to water penetration under uniform static air pressure differences. The air-pressure differences acting across a building envelope vary greatly. These factors should be fully considered prior to specifying the test pressure difference to be used.
Note 1: In applying the results of tests by this test method, note that the performance of a wall or its components, or both, may be a function of proper installation and adjustment. In service, the performance will also depend on the rigidity of supporting construction and on the resistance of components to deterioration by various causes, vibration, thermal expansion and contraction, etc. It is difficult to simulate the identical complex wetting conditions that can be encountered in service, with large wind-blown water drops, increasing water drop impact pressures with increasing wind velocity, and lateral or upward moving air and water. Some designs are more sensitive than others to this upward moving water.
Note 2: This test method does not identify unobservable liquid water which may penetrate into the test specimen.
SCOPE
1.1 This test method covers the determination of the resistance of exterior windows, curtain walls, skylights, and doors to water penetration when water is applied to the outdoor face and exposed edges simultaneously with a uniform static air pressure at the outdoor face higher than the pressure at the indoor face.  
1.2 This test method is applicable to any curtain-wall area or to windows, skylights, or doors alone.  
1.3 This test method addresses water penetration through a manufactured assembly. Water that penetrates the assembly, but does not result in a failure as defined herein, may have adverse effects on the performance of contained materials such as sealants and insulating or laminated glass. This test method does not address these issues.  
1.4 The proper use of this test method requires a knowledge of the principles of pressure measurement.  
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 7.1.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM E72-22(Test Method)
Standard Test Methods of Conducting Strength Tests of Panels for Building Construction

SIGNIFICANCE AND USE
8.1 The procedures described are those that will test the behavior of segments of wall construction under conditions representative of those encountered in service. Performance criteria based on data from those procedures can ensure structural adequacy and service life.
SCOPE
1.1 These test methods cover the following procedures for determining the structural properties of segments of wall, floor, and roof constructions:    
Section  
Test Specimens  
3  
Loading  
4  
Deformation Measurements  
5  
Reports  
6  
Precision and Accuracy  
7  
TESTING WALLS  
Significance and Use  
8  
Compressive Load  
9  
Tensile Load  
10  
Transverse Load—Specimen Horizontal  
11  
Transverse Load—Specimen Vertical  
12  
Concentrated Load  
13  
Impact Load—See Test Methods E695 and E661  
Racking Load—Evaluation of Sheathing Materials
on a Standard Wood Frame  
14  
Racking Load—Evaluation of Sheathing Materials (Wet)
on a Standard Wood Frame  
15  
TESTING FLOORS  
Significance and Use  
16  
Transverse Load  
17  
Concentrated Load  
18  
Impact Load—See Test Methods E695 and E661  
TESTING ROOFS  
Section  
Significance and Use  
19  
Transverse Load  
20  
Concentrated Load  
21  
APPENDIX  
Technical Interpretation  
Appendix X1  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    14 pages
    English language
    sale 15% off
  • Standard
    14 pages
    English language
    sale 15% off
ASTM
ASTM E2556/E2556M-10(2022)(Specification)
Standard Specification for Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment

SCOPE
1.1 This specification is limited to vapor permeable flexible sheet materials which are intended to be mechanically attached and are generally installed behind the cladding system in exterior walls.  
1.2 This specification is limited to the evaluation of materials and does not address installed performance. Although the fastening practices (type of fastener, fastening schedule, etc.) may affect the installed function of these materials, they are not included in this specification.  
1.3 This specification does not address integration of the water-resistive barrier with other wall elements. The topic is addressed in more detail in Practice E2112 and Guide E2266.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
ASTM
ASTM E330/E330M-14(2021)(Test Method)
Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference

SIGNIFICANCE AND USE
5.1 This test method is a standard procedure for determining structural performance under uniform static air pressure difference. This typically is intended to represent the effects of a wind load on exterior building surface elements. The actual loading on building surfaces is quite complex, varying with wind direction, time, height above ground, building shape, terrain, surrounding structures, and other factors. The resistance of many windows, curtain walls, and door assemblies to wind loading is also complex and depends on the complete history of load, magnitude, duration, and repetition. These factors are discussed in ASCE/SEI 7 and in the literature (1-8).5  
5.2 Design wind velocities are selected for particular geographic locations and probabilities of occurrence based on data from wind velocity maps such as are provided in ASCE/SEI 7. These wind velocities are translated into uniform static air pressure differences and durations acting inward and outward. Complexities of wind pressures, as related to building design, wind intensity versus duration, frequency of occurrence, and other factors must be considered. Superimposed on sustained winds are gusting winds which, for short periods of time from a fraction of a second to a few seconds, are capable of moving at considerably higher velocities than the sustained winds. The analytical procedures in ASCE/SEI 7, wind tunnel studies, computer simulations, and model analyses are helpful in determining the appropriate design wind loads on exterior surface elements of buildings. Generally, wind load durations obtained from ASCE/SEI 7 are 2 s to 10 s and are dependent upon the specific time reference employed in determining the pressure coefficients.  
5.3 Some materials have strength or deflection characteristics that are time dependent. Therefore, the duration of the applied test load may have a significant impact on the performance of materials used in the test specimen. The most common examples of materials with...
SCOPE
1.1 This test method describes the determination of the structural performance of exterior windows, doors, skylights, and curtain walls under uniform static air pressure differences, using a test chamber. This test method is applicable to curtain wall assemblies including, but not limited to, metal, glass, masonry, and stone components.2  
1.2 This test method is intended only for evaluating the structural performance associated with the specified test specimen and not the structural performance of adjacent construction.  
1.3 The proper use of this test method requires a knowledge of the principles of pressure and deflection measurement.  
1.4 This test method describes the apparatus and the procedure to be used for applying uniformly distributed test loads to a specimen.  
1.4.1 Procedure A (see 11.2) shall be used when a load-deflection curve is not required.  
1.4.2 Procedure B (see 11.3) shall be used when a load-deflection curve is required.  
1.5 The text of this standard references notes and footnotes which provide explanatory materials. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 7.  
1.8 This international standard was developed in accordance with int...

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E3036-15(2021)(Guide)
Standard Guide for Notating Facade Conditions in the Field

SCOPE
1.1 This guide consists of symbols and notations pertaining to documenting deficient conditions observed during facade inspections.  
1.2 The purpose of this guide is to provide a quick shorthand, notation system that will serve as a uniform system for facade inspectors to record their observations on existing elevation drawings or photographs, or both, of existing building facades.  
1.3 This guide is not intended to be used to record or document a diagnosis for the particular symptom.  
1.4 Notations are listed in alphabetical order. Compound terms appear as per the first word as spoken.  
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1825-21(Guide)
Standard Guide for Evaluation of Building Exterior Enclosure Materials, Products, and Systems

SIGNIFICANCE AND USE
4.1 This guide may be used by design professionals and others in the building construction industry to provide factual support for professional judgment of materials, products, or systems during the design development of new and remedial building exterior enclosure construction.  
4.2 This guide is intended to provide guidance to the user of this standard in the evaluation and qualification of materials, products, or systems with which they do not have substantial, long-term experience or that are intended to be employed in a new or different manner. The standard may be used to investigate and assess the probable performance of such materials, products, or systems in relation to the proposed use on or as part of a building exterior enclosure.  
4.3 The procedures outlined in Section 5 will help guide the user in making informed selections based on the materials, products, or systems performance history on constructed projects and provide information on limitations of use, the manufacturer’s performance history, and current status. The use of this guide will reduce, but not eliminate, the risk of in-service performance problems with materials, products, or systems.  
4.4 The procedures listed in this guide are intended for use in selecting materials, products, or systems that are critical to the safety, function, or serviceability of a building, or where they constitute substantial components of the work. The recommendations in this guide are not applicable to all materials, products, or systems that can be incorporated in buildings. The user must exercise appropriate judgment and care regarding the need when applying the various procedures included in this guide, including the use of the form included in Appendix X1, with regard to particular materials, products, or systems, and specific buildings. Materials, products, or systems that will be used for a noncritical or incidental use usually do not require an exhaustive evaluation. Materials, products, or systems ...
SCOPE
1.1 This guide covers guidance to design professionals in the evaluation of materials, products, or systems with which they are not familiar and to help determine that the selected materials, products, or systems are suitable for use on or as a part of a building’s exterior enclosure.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    6 pages
    English language
    sale 15% off
  • Guide
    6 pages
    English language
    sale 15% off
ASTM
ASTM E2128-20(Guide)
Standard Guide for Evaluating Water Leakage of Building Walls

SIGNIFICANCE AND USE
4.1 This guide is intended to provide building professionals with a comprehensive methodology for evaluating water leakage through walls. It addresses the performance expectations and service history of a wall, the various components of a wall, and the interaction between these components and adjacent construction. It is not intended as a construction quality control procedure, nor as a preconstruction qualification procedure. It is intended for evaluating buildings that exhibit water leakage.  
4.1.1 Qualifications—This guide requires the evaluator to possess a knowledge of basic physics and of construction and wall design principles and practices.  
4.1.2 Application—The sequential activities described herein are intended to produce a complete and comprehensive evaluation program, but all activities may not be applicable or necessary for a particular evaluation program. It is the responsibility of the professional using this guide to determine the activities and sequence necessary to properly perform an appropriate leakage evaluation for a specific building.  
4.1.3 Preliminary Assessment—A preliminary assessment may indicate that water leakage problems are limited to a specific element or portion of a wall. The preliminary assessment may also indicate that the wall is not the source of a leak even though it is perceived as such by the building occupant. The presence of water might result from a roofing problem, a condensation problem, a plumbing problem, operable windows or doors left opened or unlatched or some other condition not directly related to water leakage through the building wall and is outside the scope of this guide. The evaluation of causes may likewise be limited in scope, and the procedures recommended herein abridged according to the professional judgement of the evaluator. A statement stipulating the limits of the investigation should be included in the report.  
4.1.4 Expectations—Expectations about the overall effectiveness of an evaluatio...
SCOPE
1.1 This guide describes methods for determining and evaluating causes of water leakage of exterior walls. For this purpose, water penetration is considered leakage, and therefore problematic, if it exceeds the planned resistance or temporary retention and drainage capacity of the wall, is causing or is likely to cause premature deterioration of a building or its contents, or is adversely affecting the performance of other components. A wall is considered a system including its exterior and interior finishes, fenestration, structural components, and components for maintaining the building interior environment.  
1.2 Investigative techniques discussed may be intrusive, disruptive, or destructive. It is the responsibility of the investigator to establish the limitations of use, to anticipate and advise of the destructive nature of some procedures, and to plan for patching and selective reconstruction as necessary.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3.1 Exception—Solely inch-pound units are stated in 10.3.1, 10.3.2.1, X1.5.3.7, X2.5.1.3, X3.4.3.3, X5.1.2.2, X5.5.5, X5.6.3, and X8.5.1.3.  
1.4 This practice does not purport to address all of the safety concerns, if any, associated with its use. Establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Awareness of safety and familiarity with safe procedures are particularly important for above-ground operations on the exterior of a building and destructive investigative procedures which typically are associated with the work described in this guide.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of Internat...

  • Guide
    39 pages
    English language
    sale 15% off
  • Guide
    39 pages
    English language
    sale 15% off
ASTM
ASTM E3223/E3223M-20(Guide)
Standard Guide for Specifying and Testing Field-Constructed Exterior Building Wall System Mockups in New Construction

SIGNIFICANCE AND USE
4.1 This guide is intended to assist the construction team in evaluating the constructability, functionality, sequence of construction, interference, tolerances, component performance, and assembled system performance of the exterior wall systems.  
4.2 This guide does not establish specific roles for the parties involved during construction or the contractual obligations of those parties. The role of each party within any specific project should be established and documented before the start of the project.  
4.3 This guide is intended for use when specifying construction mockups that are either integrated mockups or off-structure mockups.  
4.4 This guide is intended to aid the specifier in the development of a QA mockup program for assessing the performance of exterior walls. It is not intended to provide a comprehensive list of applicable test methods for QA testing available or applicable to a mockup program.  
4.5 This guide does not address preconstruction laboratory testing of a wall system.  
4.6 This guide is intended to address technical issues with the performance of the wall system and the interconnection of the various components and systems. A mockup may or may not be used as an aesthetic mockup; however, this guide is not intended to address aesthetic issues with the wall system.  
4.7 This guide is not intended to provide guidance for construction observation services. However, the mockup may be useful to inform inspectors of the intended construction, sequence, materials, and interface conditions encountered on the project and serve as a standard of quality to which the remainder of construction can be compared.
SCOPE
1.1 This guide provides information to assist in the specification, design, and performance testing of field-constructed exterior wall assemblies (“mockups”) for construction projects. This includes testing procedures appropriate to evaluate the component and assembly performance for water penetration resistance, air leakage resistance, and other test methods that may be applied as part of the quality assurance (QA) program for the installed systems.  
1.2 This guide is intended to be applied to exterior wall mockups that include components, systems, and assemblies including, but not limited to, curtain walls, windows, doors, masonry walls, precast concrete, cast-in-place concrete, exterior insulation and finish system (EIFS), roofing interfaces, stucco, wood siding, metal panels, sealants, appurtenances, penetrations, louvers, and combinations thereof. Such mockups are expected to include the intersection between wall systems.  
1.3 This guide is not intended to provide a comprehensive list of potential testing that may be applicable to field-constructed mockups. Additional tests may be applicable to mockups for specific projects.  
1.4 This guide is not intended to address all possible project delivery methods and as such the requirements listed herein must be evaluated by the specifier for appropriateness with the delivery method.  
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical...

  • Guide
    11 pages
    English language
    sale 15% off