ASTM F2163-01(2008)

Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring

ABSTRACT
This specification covers inner rings for needle roller bearings with drawn outer rings. The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged. Bearing inner rings shall be manufactured of steel, alloy or carbon. The raceway (outside diameter) surface shall have a maximum surface roughness conforming to the requirements specified.
SCOPE
1.1 This specification covers inner rings for needle roller bearings with drawn outer rings.
1.2 The inner rings specified in this specification are intended for use on unhardened shafts in conjunction with open end needle roller bearings shown on Specification F 2162 and MS52141.
1.3 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged.
1.4 The inner rings specified in this specification are not intended for use in flight-critical systems of aircraft.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1—This specification contains many of the requirements of MS17130, which was originally developed by the Department of Defense and is currently maintained by the Defense Supply Center Richmond.

General Information

• Status: Historical
• Publication Date: 30-Apr-2008
• ICS: 21.100.20 - Rolling bearings
• Technical Committee: F34 - Rolling Element Bearings
• Drafting Committee: F34.04 - Automotive/Industrial Bearing

Relations

• Replaces: ASTM F2163-01e1 - Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring
• Effective Date: 01-May-2008
• Replaced By: ASTM F2163-01(2016) - Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring
• Effective Date: 01-May-2016
• Referred By: ASTM F2431-04(2018) - Standard Specification for Ring Bearing, Inner: For Needle Roller Bearing with Thick Outer Ring
• Effective Date: 01-May-2008
• Referred By: ASTM F2162-01(2016) - Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type
• Effective Date: 01-May-2008

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2163 −01(Reapproved 2008)
Standard Specification for
Ring, Bearing, Inner: for Needle Roller Bearing With Drawn
Outer Ring
This standard is issued under the fixed designation F2163; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2.2 ASME Standard:
ASME B 46.1 Surface Texture Surface Roughness,
1.1 This specification covers inner rings for needle roller
Waviness, and Lay
bearings with drawn outer rings.
2.3 SAE Standards:
SAE AHS STD-66
1.2 The inner rings specified in this specification are in-
SAE J-404 Chemical Composition of SAE Alloy Steels
tended for use on unhardened shafts in conjunction with open
2.4 Military Standards:
end needle roller bearings shown on Specification F2162 and
MIL-STD-130 Identification Marking of US Military Prop-
MS52141.
erty
1.3 Theuseofrecycledmaterialsthatmeettherequirements
MS52141 Bearing, Roller, Needle: Drawn Outer Ring,
of the applicable material specification without jeopardizing
Caged, Without Inner Ring, Open and Closed End, Stan-
the intended use of the item is encouraged.
dard Type
2.5 American Bearing Manufacturer’s Association (ABMA)
1.4 The inner rings specified in this specification are not
Standard:
intended for use in flight-critical systems of aircraft.
STD 4 Tolerance Definitions and Gauging Practices For Ball
1.5 The values stated in inch-pound units are to be regarded
and Roller Bearings
as standard. The values given in parentheses are mathematical 2.6 ISO Standard:
conversions to SI units that are provided for information only ISO 5593 Rolling Bearings—Vocabulary
and are not considered standard.
3. Terminology
NOTE 1—This specification contains many of the requirements of
3.1 Definitions—For definitions of terms used in this
MS17130, which was originally developed by the Department of Defense
specification, refer to ABMA STD 4 and ISO 5593.
and is currently maintained by the Defense Supply Center Richmond.
4. Ordering Information
2. Referenced Documents
4.1 When ordering parts in accordance with this
2.1 ASTM Standards:
specification, specify the following:
E18 Test Methods for Rockwell Hardness of Metallic Ma-
4.1.1 ASTM designation number, including year of issue;
terials
4.1.2 Dash number (see Table 1); and
F2162 Specification for Bearing, Roller, Needle: Drawn 4.1.3 Dimensions of inner rings, including:
Outer Ring, Full Complement, Without Inner Ring, Open 4.1.3.1 Bore diameter, in.;
and Closed End, Standard Type 4.1.3.2 Outside diameter, in.;
4.1.3.3 Width, in.; and
1 3
This specification is under the jurisdiction ofASTM Committee F34 on Rolling Available from Global Engineering Documents, 15 Inverness Way, East
Element Bearings and is the direct responsibility of Subcommittee F34.04 on Englewood, CO 80112-5704, http://www.global.ihs.com.
Automotive/Industrial Bearing. Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Current edition approved May 1, 2008. Published October 2008. Originally Dr., Warrendale, PA 15096-0001, http://www.sae.org.
ε1
approved in 2001. Last previous edition approved in 2001 as F2163–01 DOI: Available from USAInformation Systems, 1092 Laskin Rd., Ste. 208, Virginia
10.1520/F2163-01R08. Beach, VA 23451.
2 6
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from the American Bearing Manufacturer’s Association, 1200 19th
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM St. NW, Ste. 300, Washington, DC 20036–2401.
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F2163−01 (2008)
TABLE 1 Inner Ring Dimensions
d F B Mating
Bore Diameter, in. Outside Diameter, in. Width, in. Bearings
Dash r
F2162
Nominal Minimum Maximum Nominal Minimum Maximum Minimum Maximum
Number Radius, in.
Dash Num-
A
bers
3 9
–61 ⁄8 0.3745 0.3750 ⁄16 0.5620 0.5625 0.505 0.515 0.025 –16
3 9
–62 ⁄8 0.3745 0.3750 ⁄16 0.5620 0.5625 0.755 0.765 0.025 –17
3 5
–63 ⁄8 0.3745 0.3750 ⁄8 0.6245 0.6250 0.505 0.515 0.025 –18
3 5
–1 ⁄8 0.3745 0.3750 ⁄8 0.6245 0.6250 0.755 0.765 0.025 –19
7 5
–64 ⁄16 0.4370 0.4375 ⁄8 0.6245 0.6250 0.776 0.789 0.025 –19
1 3
–65 ⁄2 0.4995 0.5000 ⁄4 0.7495 0.7500 0.505 0.515 0.040 –22
1 3
–2 ⁄2 0.4995 0.5000 ⁄4 0.7495 0.7500 0.755 0.765 0.040 –23
5 7
–4 ⁄8 0.6245 0.6250 ⁄8 0.8745 0.8750 0.755 0.765 0.040 –26
5 7
–66 ⁄8 0.6245 0.6250 ⁄8 0.8745 0.8750 1.005 1.015 0.040 –27
–5 ⁄4 0.7495 0.7500 1 0.9995 1.0000 0.755 0.765 0.040 –29
–67 ⁄4 0.7495 0.7500 1 0.9995 1.0000 1.005 1.015 0.040 –30
–6 ⁄16 0.8120 0.8125 1 0.9995 1.0000 0.755 0.765 0.040 –29
–7 ⁄16 0.8120 0.8125 1 0.9995 1.0000 1.005 1.015 0.040 –30
7 1
–8 ⁄8 0.8745 0.8750 1 ⁄8 1.1245 1.1250 1.005 1.015 0.040 –33
15 1
–9 ⁄16 0.9370 0.9375 1 ⁄8 1.1245 1.1250 1.005 1.015 0.040 –33
–10 1 0.9995 1.0000 1 ⁄4 1.2495 1.2500 1.005 1.015 0.040 –35
–11 1 0.9995 1.0000 1 ⁄4 1.2495 1.2500 1.255 1.265 0.040 –36
1 3
–13 1 ⁄8 1.1245 1.1250 1 ⁄8 1.3745 1.3750 1.255 1.26
...