ASTM F2163-01e1

Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring

SCOPE
1.1 This specification covers inner rings for needle roller bearings with drawn outer rings.
1.2 The inner rings specified in this specification are intended for use on unhardened shafts in conjunction with open end needle roller bearings shown on Specification F 2162 and MS52141.
1.3 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged.
1.4 The inner rings specified in this specification are not intended for use in flight-critical systems of aircraft.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
Note 1—This specification was originally developed by the Department of Defense and maintained by the Defense Supply Center Richmond. It is intended to replicate the requirements of MS 17130.

General Information

• Status: Historical
• Publication Date: 09-Dec-2001
• ICS: 21.100.20 - Rolling bearings
• Technical Committee: F34 - Rolling Element Bearings
• Drafting Committee: F34.04 - Automotive/Industrial Bearing

Relations

• Replaces: ASTM F2163-01 - Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring
• Effective Date: 10-Dec-2001
• Replaced By: ASTM F2163-01(2008) - Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring
• Effective Date: 01-May-2008
• Referred By: ASTM F2431-04(2018) - Standard Specification for Ring Bearing, Inner: For Needle Roller Bearing with Thick Outer Ring
• Effective Date: 10-Dec-2001
• Referred By: ASTM F2162-01(2016) - Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type
• Effective Date: 10-Dec-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
e1
Designation: F 2163 – 01
Standard Specification for
Ring, Bearing, Inner: for Needle Roller Bearing With Drawn
1
Outer Ring
This standard is issued under the fixed designation F 2163; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Note 1 was changed editorially in June 2002.
1. Scope 2.3 SAE Standards:
4
SAE AHS STD-66
1.1 This specification covers inner rings for needle roller
4
SAE J-404 Chemical Composition of SAE Alloy Steels
bearings with drawn outer rings.
2.4 Military Standards:
1.2 The inner rings specified in this specification are in-
MIL-STD-130 Identification Marking of US Military Prop-
tended for use on unhardened shafts in conjunction with open
5
erty
end needle roller bearings shown on Specification F 2162 and
MS52141 Bearing, Roller, Needle: Drawn Outer Ring,
MS52141.
Caged, Without Inner Ring, Open and Closed End, Stan-
1.3 Theuseofrecycledmaterialsthatmeettherequirements
5
dard Type
of the applicable material specification without jeopardizing
2.5 American Bearing Manufacturer’s Association (ABMA)
the intended use of the item is encouraged.
Standard:
1.4 The inner rings specified in this specification are not
STD 4 Tolerance Definitions and Gauging Practices For
intended for use in flight-critical systems of aircraft.
6
Ball and Roller Bearings
1.5 The values stated in inch-pound units are to be regarded
2.6 ISO Standard:
as the standard. The values given in parentheses are provided
7
ISO 5593 Rolling Bearings—Vocabulary
for information only.
NOTE 1—This specification contains many of the requirements of 3. Terminology
MS17130, which was originally developed by the Department of Defense
3.1 Definitions—For definitions of terms used in this speci-
and is currently maintained by the Defense Supply Center Richmond.
fication, refer to ABMA STD 4 and ISO 5593.
2. Referenced Documents
4. Ordering Information
2
2.1 ASTM Standards:
4.1 When ordering parts in accordance with this specifica-
E18 Test Methods for Rockwell Hardness and Rockwell
tion, specify the following:
Superficial Hardness of Metallic Materials
4.1.1 ASTM designation number, including year of issue;
F 2162 Specification for Bearing, Roller, Needle: Drawn
4.1.2 Dash number (see Table 1); and
Outer Ring, Full Complement, Without Inner Ring, Open
4.1.3 Dimensions of inner rings, including:
and Closed End, Standard Type
4.1.3.1 Bore diameter, in.;
2.2 ASME Standard:
4.1.3.2 Outside diameter, in.;
ASME B 46.1 Surface Texture Surface Roughness, Wavi-
4.1.3.3 Width, in.; and
3
ness, and Lay
4.1.3.4 Radius, in.
1
ThisspecificationisunderthejurisdictionofASTMCommitteeF34onRolling
Element Bearings and is the direct responsibility of Subcommittee F34.04 on
4
Automotive/Industrial Bearing. Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Current edition approved Dec. 10, 2001. Published March 2002. Dr., Warrendale, PA 15096-0001.
2 5
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from USAInformation Systems, 1092 Laskin Rd., Ste. 208, Virginia
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Beach, VA 23451.
6
Standards volume information, refer to the standard’s Document Summary page on Available from the American Bearing Manufacturer’s Association, 1200 19th
the ASTM website. St. NW, Ste. 300, Washington, DC 20036–2401.
3 7
Available from Global Engineering Documents, 15 Inverness Way, East Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
Englewood, CO 8011. 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e1
F2163–01
TABLE 1 Inner Ring Dimensions
d F B Mating
Bore Diameter, in. Outside Diameter, in. Width, in. Bearings
Dash r
F 2162
Number Radius, in.
Dash
Nominal Minimum Maximum Nominal Minimum Maximum Minimum Maximum
A
Numbers
3 9
–61 ⁄8 0.3745 0.3750 ⁄16 0.5620 0.5625 0.505 0.515 0.025 –16
3 9
–62 ⁄8 0.3745 0.3750 ⁄16 0.5620 0.5625 0.755 0.765 0.025 –17
3 5
–63 ⁄8 0.3745 0.3750 ⁄8 0.6245 0.6250 0.505 0.515 0.025 –18
3 5
–1 ⁄8 0.3745 0.3750 ⁄8 0.6245 0.6250 0.755 0.765 0.025 –19
7 5
–64 ⁄16 0.4370 0.4375 ⁄8 0.6245 0.6250 0.776 0.789 0.025 –19
1 3
–65 ⁄2 0.4995 0.5000 ⁄4 0.7495 0.7500 0.505 0.515 0.040 –22
1 3
–2 ⁄2 0.4995 0.5000 ⁄4 0.7495 0.7500 0.755 0.765 0.040 –23
5 7
–4 ⁄8 0.6245 0.6250 ⁄8 0.8745 0.8750 0.755 0.765 0.040 –26
5 7
–66 ⁄8 0.6245 0.6250 ⁄8 0.8745 0.8750 1.005 1.015 0.040 –
...