ASTM B348-11

Standard Specification for Titanium and Titanium Alloy Bars and Billets

ABSTRACT
This specification covers annealed bars and grills made from titanium or its alloys. All material grades covered should conform to the required chemical composition requirements. Elements that are intentionally added to the melt should be identified, analyzed and reported in the chemical analysis. Specimens for tension tests should be machined and the tensile properties determined using a specified strain rate through the yield strength and at an increasing rate. Each annealed material may be furnished as either descaled, sandblasted, ground, or rough turned.
SCOPE
1.1 This specification covers annealed titanium and titanium alloy bars and billets as follows:
1.1.1 Grade 1—Unalloyed titanium,
1.1.2 Grade 2—Unalloyed titanium,
1.1.2.1 Grade 2H—Unalloyed titanium (Grade 2 with 58 ksi minimum UTS),
1.1.3 Grade 3—Unalloyed titanium,
1.1.4 Grade 4—Unalloyed titanium,
1.1.5 Grade 5—Titanium alloy (6 % aluminum, 4 % vanadium),
1.1.6 Grade 6—Titanium alloy (5 % aluminum, 2.5 % tin),
1.1.7 Grade 7—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi minimum UTS),
1.1.8 Grade 9—Titanium alloy (3 % aluminum, 2.5 % vanadium),
1.1.9 Grade 11—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.10 Grade 12—Titanium alloy (0.3 % molybdenum, 0.8 % nickel),
1.1.11 Grade 13—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.12 Grade 14—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.13 Grade 15—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.14 Grade 16—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.14.1 Grade 16H—Unalloyed titanium plus 0.04 to 0.08 % palladiumm (Grade 16 with 58 ksi minimum UTS),
1.1.15 Grade 17—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.16 Grade 18—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,
1.1.17 Grade 19—Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),
1.1.18 Grade 20—Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus 0.04 %–0.08 % palladium,  
1.1.19 Grade 21—Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),
1.1.20 Grade 23—Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI),
1.1.21 Grade 24—Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,
1.1.22 Grade 25—Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,
1.1.23 Grade 26—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.23.1 Grade 26H—Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),
1.1.24 Grade 27—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.25 Grade 28—Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.08–0.14 % ruthenium),
1.1.26 Grade 29—Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI plus 0.08 to 0.14 % ruthenium),
1.1.27 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.28 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.29 Grade 32—Titanium alloy (5 % aluminum, 1 % tin, 1 % zirconium, 1 % vanadium, 0.8 % molybdenum),
1.1.30 Grade 33—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.31 Grade 34—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.32 Grade 35—Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),
1.1.33 Grade 36—Titanium alloy (45 % niobium),
1.1.34 Grade 37—Titanium alloy (1.5 % aluminum), and
1.1.35 Grade 38—Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron).
Note 1—H grade material is identical to the corresponding numeric grade (that is, Grade 2H = Grade 2) except for the higher guaranteed minimum UTS, and may always be certified as meeting the requirements of...

General Information

• Status: Historical
• Publication Date: 30-Jun-2011
• ICS: 77.150.50 - Titanium products
• Technical Committee: B10 - Reactive and Refractory Metals and Alloys
• Drafting Committee: B10.01 - Titanium

Relations

• Replaces: ASTM B348-10 - Standard Specification for Titanium and Titanium Alloy Bars and Billets
• Effective Date: 01-Jul-2011
• Replaced By: ASTM B348-13 - Standard Specification for Titanium and Titanium Alloy Bars and Billets
• Effective Date: 01-Jul-2013
• Referred By: ASTM B363-19 - Standard Specification for Seamless and Welded Unalloyed Titanium and Titanium Alloy Welding Fittings
• Effective Date: 01-Jul-2011
• Referred By: ASTM F1511-18(2023) - Standard Specification for Mechanical Seals for Shipboard Pump Applications
• Effective Date: 01-Jul-2011
• Referred By: ASTM F67-13(2017) - Standard Specification for Unalloyed Titanium, for Surgical Implant Applications (UNS R50250, UNS R50400, UNS R50550, UNS R50700)
• Effective Date: 01-Jul-2011
• Referred By: ASTM F3122-14(2022) - Standard Guide for Evaluating Mechanical Properties of Metal Materials Made via Additive Manufacturing Processes
• Effective Date: 01-Jul-2011
• Referred By: ASTM F2182-19e2 - Standard Test Method for Measurement of Radio Frequency Induced Heating On or Near Passive Implants During Magnetic Resonance Imaging
• Effective Date: 01-Jul-2011
• Referred By: ASTM B988-18(2022) - Standard Specification for Powder Metallurgy (PM) Titanium and Titanium Alloy Structural Components
• Effective Date: 01-Jul-2011
• Referred By: ASTM B381-21 - Standard Specification for Titanium and Titanium Alloy Forgings
• Effective Date: 01-Jul-2011
• Referred By: ASTM F1155-10(2019) - Standard Practice for Selection and Application of Piping System Materials
• Effective Date: 01-Jul-2011
• Referred By: ASTM B1009-20 - Standard Specification for Titanium Alloy Bars for Near Surface Mounts in Civil Structures
• Effective Date: 01-Jul-2011

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B348 −11
StandardSpecification for
1
Titanium and Titanium Alloy Bars and Billets
This standard is issued under the fixed designation B348; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* 1.1.16 Grade 18—Titanium alloy (3 % aluminum, 2.5 %
2 vanadium) plus 0.04 to 0.08 % palladium,
1.1 This specification covers annealed titanium and tita-
1.1.17 Grade 19—Titanium alloy (3 % aluminum, 8 %
nium alloy bars and billets as follows:
vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),
1.1.1 Grade 1—Unalloyed titanium,
1.1.18 Grade 20—Titanium alloy (3 % aluminum, 8 %
1.1.2 Grade 2—Unalloyed titanium,
vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum)
1.1.2.1 Grade 2H—Unalloyedtitanium(Grade2with58ksi
plus 0.04 %–0.08 % palladium,
minimum UTS),
1.1.19 Grade 21—Titanium alloy (15 % molybdenum, 3 %
1.1.3 Grade 3—Unalloyed titanium,
aluminum, 2.7 % niobium, 0.25 % silicon),
1.1.4 Grade 4—Unalloyed titanium,
1.1.20 Grade 23—Titanium alloy (6 % aluminum, 4 % va-
1.1.5 Grade 5—Titanium alloy (6 % aluminum, 4 %
nadium with extra low interstitial elements, ELI),
vanadium),
1.1.21 Grade 24—Titanium alloy (6 % aluminum, 4 % va-
1.1.6 Grade 6—Titanium alloy (5 % aluminum, 2.5 % tin),
nadium) plus 0.04 % to 0.08 % palladium,
1.1.7 Grade 7—Unalloyed titanium plus 0.12 to 0.25 %
1.1.22 Grade 25—Titanium alloy (6 % aluminum, 4 % va-
palladium,
nadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 %
1.1.7.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 %
palladium,
palladium (Grade 7 with 58 ksi minimum UTS),
1.1.23 Grade 26—Unalloyed titanium plus 0.08 to 0.14 %
1.1.8 Grade 9—Titanium alloy (3 % aluminum, 2.5 %
ruthenium,
vanadium),
1.1.23.1 Grade 26H—Unalloyed titanium plus 0.08 to
1.1.9 Grade 11—Unalloyed titanium plus 0.12 to 0.25 %
0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),
palladium,
1.1.24 Grade 27—Unalloyed titanium plus 0.08 to 0.14 %
1.1.10 Grade 12—Titanium alloy (0.3 % molybdenum,
ruthenium,
0.8 % nickel),
1.1.25 Grade 28—Titanium alloy (3 % aluminum, 2.5 %
1.1.11 Grade 13—Titanium alloy (0.5 % nickel, 0.05 %
vanadium plus 0.08–0.14 % ruthenium),
ruthenium),
1.1.26 Grade 29—Titanium alloy (6 % aluminum, 4 %
1.1.12 Grade 14—Titanium alloy (0.5 % nickel, 0.05 %
vanadium, extra low interstitial, ELI plus 0.08 to 0.14 %
ruthenium),
ruthenium),
1.1.13 Grade 15—Titanium alloy (0.5 % nickel, 0.05 %
1.1.27 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 %
ruthenium),
palladium),
1.1.14 Grade 16—Unalloyed titanium plus 0.04 to 0.08 %
1.1.28 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 %
palladium,
palladium),
1.1.14.1 Grade 16H—Unalloyed titanium plus 0.04 to
1.1.29 Grade 32—Titanium alloy (5 % aluminum, 1 % tin,
0.08 % palladiumm (Grade 16 with 58 ksi minimum UTS),
1 % zirconium, 1 % vanadium, 0.8 % molybdenum),
1.1.15 Grade 17—Unalloyed titanium plus 0.04 to 0.08 %
1.1.30 Grade 33—Titanium alloy (0.4 % nickel, 0.015 %
palladium,
palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.31 Grade 34—Titanium alloy (0.4 % nickel, 0.015 %
palladium, 0.025 % ruthenium, 0.15 % chromium),
1
This specification is under the jurisdiction of ASTM Committee B10 on
1.1.32 Grade 35—Titanium alloy (4.5 % aluminum, 2 %
Reactive and Refractory Metals and Alloys and is the direct responsibility of
molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),
Subcommittee B10.01 on Titanium.
Current edition approved July 1, 2011. Published July 2011. Originally approved
1.1.33 Grade 36—Titanium alloy (45 % niobium),
in 1959. Last previous edition approved in 2010 as B348 – 10. DOI: 10.1520/
1.1.34 Grade 37—Titanium alloy (1.5 % aluminum), and
B0348-11.
2
1.1.35 Grade 38—Titanium alloy (4 % aluminum, 2.5 %
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
cation SB-348 in Section II of that Code. vanadium, 1.5 % iron).
*A Summary of Changes section appears at the end of this standard
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959. United States
1

---------------------- Page: 1 ----------------------
B348−11
NOTE 1—H grade material is identical to the corresponding numeric
4.1.2 Product classification (Section 3),
grade (that is, Grade 2H = Grade 2) except for the higher guaranteed
4.1.3 Chemistry (Table 1),
minimum UTS, and may always be certified as meeting the requirements
4.1.4 Mechanical properties (Table 2),
of its corresponding numeric grade. Grades 2H, 7H, 16H, and 26H are
intended primarily for pressure vessel use. 4.1.5 Marking (Section 16),
The H gra
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B348–10 Designation: B348 – 11
Standard Specification for
1
Titanium and Titanium Alloy Bars and Billets
This standard is issued under the fixed designation B348; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers annealed titanium and titanium alloy bars and billets as follows:
1.1.1 Grade 1—Unalloyed titanium,
1.1.2 Grade 2—Unalloyed titanium,
1.1.2.1 Grade 2H—Unalloyed titanium (Grade 2 with 58 ksi minimum UTS),
1.1.3 Grade 3—Unalloyed titanium,
1.1.4 Grade 4—Unalloyed titanium,
1.1.5 Grade 5—Titanium alloy (6 % aluminum, 4 % vanadium),
1.1.6 Grade 6—Titanium alloy (5 % aluminum, 2.5 % tin),
1.1.7 Grade 7—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi minimum UTS),
1.1.8 Grade 9—Titanium alloy (3 % aluminum, 2.5 % vanadium),
1.1.9 Grade 11—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.10 Grade 12—Titanium alloy (0.3 % molybdenum, 0.8 % nickel),
1.1.11 Grade 13—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.12 Grade 14—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.13 Grade 15—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.14 Grade 16—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.14.1 Grade 16H—Unalloyed titanium plus 0.04 to 0.08 % palladiumm (Grade 16 with 58 ksi minimum UTS),
1.1.15 Grade 17—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.16 Grade 18—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,
1.1.17 Grade 19—Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),
1.1.18 Grade 20—Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus
0.04 %–0.08 % palladium,
1.1.19 Grade 21—Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),
1.1.20 Grade 23—Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI),
1.1.21 Grade 24—Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,
1.1.22 Grade 25—Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,
1.1.23 Grade 26—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.23.1 Grade 26H—Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),
1.1.24 Grade 27—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.25 Grade 28—Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.08–0.14 % ruthenium),
1.1.26 Grade 29—Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI plus 0.08 to 0.14 % ruthenium),
1.1.27 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.28 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.29 Grade 32—Titanium alloy (5 % aluminum, 1 % tin, 1 % zirconium, 1 % vanadium, 0.8 % molybdenum),
1.1.30 Grade 33—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.31 Grade 34—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.32 Grade 35—Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),
1
This specification is under the jurisdiction of ASTM Committee B10 on Reactive and Refractory Metals and Alloys and is the direct responsibility of Subcommittee
B10.01 on Titanium.
Current edition approved MayJuly 1, 2010.2011. Published May 2010.July 2011. Originally approved in 1959. Last previous edition approved in 20092010 as B348 – 109.
DOI: 10.1520/B0348-101.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-348 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B348 – 11
1.1.33 Grade 36—Titanium alloy (45 % niobium),
1.1.34 Grade 37—Titanium alloy (1.5 % aluminum), and
1.1.35 Grade 38—Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron).
NOTE 1—H grade material is identical to the corresponding numeric grade (that is, Grade 2H = Grade 2) except for the higher guaranteed mi
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B348–10 Designation: B348 – 11
Standard Specification for
1
Titanium and Titanium Alloy Bars and Billets
This standard is issued under the fixed designation B348; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers annealed titanium and titanium alloy bars and billets as follows:
1.1.1 Grade 1—Unalloyed titanium,
1.1.2 Grade 2—Unalloyed titanium,
1.1.2.1 Grade 2H—Unalloyed titanium (Grade 2 with 58 ksi minimum UTS),
1.1.3 Grade 3—Unalloyed titanium,
1.1.4 Grade 4—Unalloyed titanium,
1.1.5 Grade 5—Titanium alloy (6 % aluminum, 4 % vanadium),
1.1.6 Grade 6—Titanium alloy (5 % aluminum, 2.5 % tin),
1.1.7 Grade 7—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.7.1 Grade 7H—Unalloyed titanium plus 0.12 to 0.25 % palladium (Grade 7 with 58 ksi minimum UTS),
1.1.8 Grade 9—Titanium alloy (3 % aluminum, 2.5 % vanadium),
1.1.9 Grade 11—Unalloyed titanium plus 0.12 to 0.25 % palladium,
1.1.10 Grade 12—Titanium alloy (0.3 % molybdenum, 0.8 % nickel),
1.1.11 Grade 13—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.12 Grade 14—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.13 Grade 15—Titanium alloy (0.5 % nickel, 0.05 % ruthenium),
1.1.14 Grade 16—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.14.1 Grade 16H—Unalloyed titanium plus 0.04 to 0.08 % palladiumm (Grade 16 with 58 ksi minimum UTS),
1.1.15 Grade 17—Unalloyed titanium plus 0.04 to 0.08 % palladium,
1.1.16 Grade 18—Titanium alloy (3 % aluminum, 2.5 % vanadium) plus 0.04 to 0.08 % palladium,
1.1.17 Grade 19—Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum),
1.1.18 Grade 20—Titanium alloy (3 % aluminum, 8 % vanadium, 6 % chromium, 4 % zirconium, 4 % molybdenum) plus
0.04 %–0.08 % palladium,
1.1.19 Grade 21—Titanium alloy (15 % molybdenum, 3 % aluminum, 2.7 % niobium, 0.25 % silicon),
1.1.20 Grade 23—Titanium alloy (6 % aluminum, 4 % vanadium with extra low interstitial elements, ELI),
1.1.21 Grade 24—Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.04 % to 0.08 % palladium,
1.1.22 Grade 25—Titanium alloy (6 % aluminum, 4 % vanadium) plus 0.3 % to 0.8 % nickel and 0.04 % to 0.08 % palladium,
1.1.23 Grade 26—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.23.1 Grade 26H—Unalloyed titanium plus 0.08 to 0.14 % ruthenium (Grade 26 with 58 ksi minimum UTS),
1.1.24 Grade 27—Unalloyed titanium plus 0.08 to 0.14 % ruthenium,
1.1.25 Grade 28—Titanium alloy (3 % aluminum, 2.5 % vanadium plus 0.08–0.14 % ruthenium),
1.1.26 Grade 29—Titanium alloy (6 % aluminum, 4 % vanadium, extra low interstitial, ELI plus 0.08 to 0.14 % ruthenium),
1.1.27 Grade 30—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.28 Grade 31—Titanium alloy (0.3 % cobalt, 0.05 % palladium),
1.1.29 Grade 32—Titanium alloy (5 % aluminum, 1 % tin, 1 % zirconium, 1 % vanadium, 0.8 % molybdenum),
1.1.30 Grade 33—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.31 Grade 34—Titanium alloy (0.4 % nickel, 0.015 % palladium, 0.025 % ruthenium, 0.15 % chromium),
1.1.32 Grade 35—Titanium alloy (4.5 % aluminum, 2 % molybdenum, 1.6 % vanadium, 0.5 % iron, 0.3 % silicon),
1
This specification is under the jurisdiction of ASTM Committee B10 on Reactive and Refractory Metals and Alloys and is the direct responsibility of Subcommittee
B10.01 on Titanium.
Current edition approved MayJuly 1, 2010.2011. Published May 2010.July 2011. Originally approved in 1959. Last previous edition approved in 20092010 as B348 – 109.
DOI: 10.1520/B0348-101.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SB-348 in Section II of that Code.
*A Summary of Changes section appears at the end of this standard.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B348 – 11
1.1.33 Grade 36—Titanium alloy (45 % niobium),
1.1.34 Grade 37—Titanium alloy (1.5 % aluminum), and
1.1.35 Grade 38—Titanium alloy (4 % aluminum, 2.5 % vanadium, 1.5 % iron).
NOTE 1—H grade material is identical to the corresponding numeric grade (that is, Grade 2H = Grade 2) except for the higher guaranteed mi
...