Standard Specification for <span class="italic">sec</span>-Butyl Alcohol <a href="#fn00002"></a>
ABSTRACT
This specification establishes the properties and requirements for sec-butyl alcohol for use in paint, varnish, lacquer, and related products. Specimens shall be sampled and tested as appropriate, and shall adhere to the following requirements: apparent specific gravity; color (Pt-Co scale); distillation range (initial boiling point and dry point); nonvolatile matter; water; and acidity as acetic acid.
SCOPE
1.1 This specification covers sec-butyl alcohol for use in paint, varnish, lacquer, and related products.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.
1.4 For hazard information and guidance, see the supplier's Material Safety Data Sheet.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D1007 −11
Standard Specification for
1,2
sec-Butyl Alcohol
This standard is issued under the fixed designation D1007; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* and Related Products
D4052 Test Method for Density, Relative Density, and API
1.1 This specification covers sec -butyl alcohol for use in
Gravity of Liquids by Digital Density Meter
paint, varnish, lacquer, and related products.
D5386 Test Method for Color of Liquids Using Tristimulus
1.2 The values stated in SI units are to be regarded as
Colorimetry
standard. No other units of measurement are included in this
E29 Practice for Using Significant Digits in Test Data to
standard.
Determine Conformance with Specifications
E300 Practice for Sampling Industrial Chemicals
1.3 The following applies to all specified limits in this
standard; for purposes of determining conformance with this 2.2 U.S. Federal Specification:
PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging
standard, an observed value or a calculated value shall be
4
rounded off “to the nearest unit” in the last right-hand digit of
used in expressing the specification limit, in accordance with
3. Properties
the rounding-off method of Practice E29.
3.1 sec-Butyl alcohol shall conform to the following re-
1.4 For hazard information and guidance, see the supplier’s
quirements:
Material Safety Data Sheet.
Apparent specific gravity:
20/20°C 0.807 to 0.809
2. Referenced Documents
or
3
25/25°C 0.804 to 0.806
2.1 ASTM Standards:
A
Color, Pt-Co scale, max 10
D268 Guide for Sampling and Testing Volatile Solvents and
Distillation range, 760 mmHg, °C as:
Chemical Intermediates for Use in Paint and Related Initial boiling point, min 98.0
Dry point, max 101.0
Coatings and Material
Nonvolatile matter, max, mg/100 mL 5
D1078 Test Method for Distillation Range of Volatile Or-
Water, max, weight % 0.5
B
ganic Liquids Acidity, as acetic acid, max, weight % 0.002
D1209 Test Method for Color of Clear Liquids (Platinum-
A
Instrumental Pt-Co color determined byTest MethodD5386 have been shown to
Cobalt Scale)
have no statistically significant difference from Pt-Co color determined by Test
D1353 Test Method for Nonvolatile Matter in Volatile Sol-
Method D1209. However, it is not known whether sec-butyl alcohol was part of the
vents for Use in Paint, Varnish, Lacquer, and Related sample set included in the interlaboratory study.
B
Equivalent to 0.019 mg of KOH per gram of sample.
Products
D1364 Test Method for Water in Volatile Solvents (Karl
4. Sampling
Fischer Reagent Titration Method)
4.1 The material shall be sampled in accordance with
D1613 Test Method for Acidity in Volatile Solvents and
Practice E300.
Chemical Intermediates Used in Paint, Varnish, Lacquer,
5. Test Methods
5.1 The properties enumerated in this specification shall be
1
This specification is under the jurisdiction of ASTM Committee D01 on Paint
determined in accordance with the following ASTM methods:
and Related Coatings, Materials, and Applications and is the direct responsibility
D01.35 on Solvents, Plasticizer
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D1007–05
Standard Specification for secDesignation: D1007 – 11
Standard Specification for
,
1 2
sec-Butyl Alcohol
This standard is issued under the fixed designation D1007; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers sec -butyl alcohol for use in paint, varnish, lacquer, and related products.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard,
an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing
the specification limit, in accordance with the rounding-off method of Practice E29.
1.4 For hazard information and guidance, see the supplier’s Material Safety Data Sheet.
2. Referenced Documents
3
2.1 ASTM Standards:
D268 Guide for Sampling and Testing Volatile Solvents and Chemical Intermediates for Use in Paint and Related Coatings and
Material
D1078 Test Method for Distillation Range of Volatile Organic Liquids
D1209 Test Method for Color of Clear Liquids (Platinum-Cobalt Scale)
D1353 Test Method for Nonvolatile Matter in Volatile Solvents for Use in Paint, Varnish, Lacquer, and Related Products
D1364 Test Method for Water in Volatile Solvents (Karl Fischer Reagent Titration Method)
D1613 Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related
Products
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D5386 Test Method for Color of Liquids Using Tristimulus Colorimetry E1Specification for ASTM Liquid-in-Glass
Thermometers
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E300 Practice for Sampling Industrial Chemicals
2.2 U.S. Federal Specification:
4
PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging of
3. Properties
3.1 sec-Butyl alcohol shall conform to the following requirements:
Apparent specific gravity:
20/20°C 0.807 to 0.809
or
25/25°C 0.804 to 0.806
A
Color, Pt-Co scale, max 10
Distillation range, 760 mmHg, °C as:
1
This specification is under the jurisdiction ofASTM Committee D01 on Paint and Related Coatings, Materials, andApplications and is the direct responsibility D01.35
on Solvents, Plasticizers, and Chemical Intermediates .
CurrenteditionapprovedMay15,2005.PublishedMay2005.Originallyapprovedin1949.Lastpreviouseditionapprovedin2000asD1007–00.DOI:10.1520/D1007-05.
Current edition approved Nov. 1, 2011. Published November 2011. Originally approved in 1949. Last previous edition approved in 2005 as D1007 – 05. DOI:
10.1520/D1007-11.
2
This compound is also known under the names 2-butanol and secondary butanol.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.
*ASummary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D1007 – 11
Initial boiling point, min 98.0
Dry point, max 101.0
Nonvolatile matter, max, mg/100 mL 5
Water, max, weight % 0.5
B
Acidity, as acetic acid, max, weight % 0.002
__________
A
InstrumentalPt-CocolordeterminedbyTestMethodD5386havebeenshowntohavenostatisticallysignificantdifferencefromPt-CocolordeterminedbyTestMethod
D1209. However, it is not known whether sec-butyl alcohol was part of the sample set included in the interlaboratory study.
B
Equivalent to 0.019 mg of KOH per gram of sample.
4. Sampling
4.1 The material shall be sampled in accordance with Practice E300.
5. Test Methods
5.1 The properties enumerated in this specification shall be determined in accordance with the following ASTM methods:
5.1.1 Apparent Specific Gravity—Determine the apparent specific gravity at 20 or 25°C by a c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.