ASTM D868-21
(Practice)Standard Practice for Determination of Degree of Bleeding of Traffic Paint
Standard Practice for Determination of Degree of Bleeding of Traffic Paint
SIGNIFICANCE AND USE
4.1 Solvents in a traffic paint may cause bleeding of pavement constituents into the traffic marking, thereby rendering the traffic marking less effective as a lane or directional indicator. This practice describes how to prepare a panel of the coating to be tested and a reference panel coated with a specific solvent borne traffic paint to be used as a control for evaluation.
4.2 This practice can be particularly useful for evaluation of solvent borne traffic paints, but it may also be used for other types of traffic markings including waterborne traffic paints.
4.3 Two basic procedures are described for measuring the amount of bleeding. The procedure used shall be agreed upon by the purchaser and seller.
SCOPE
1.1 This practice describes test procedures for determining the degree of bleeding of traffic or pavement marking paints. A specific formulation for a solvent borne traffic paint formulation is included as a potential bleeding reference control.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D868 − 21
Standard Practice for
1
Determination of Degree of Bleeding of Traffic Paint
This standard is issued under the fixed designation D868; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E1347 Test Method for Color and Color-Difference Mea-
surement by Tristimulus Colorimetry
1.1 This practice describes test procedures for determining
the degree of bleeding of traffic or pavement marking paints.A
3. Terminology
specific formulation for a solvent borne traffic paint formula-
tion is included as a potential bleeding reference control. 3.1 Definitions of Terms Specific to This Standard:
3.1.1 bleeding characteristic, n—that condition of discolor-
1.2 The values stated in SI units are to be regarded as the
ation manifested in traffic paint when applied to tar or
standard. The values given in parentheses are for information
asphaltic-type substrates.
only.
3.1.1.1 Discussion—The amount of discoloration can be
1.3 This standard does not purport to address all of the
comparing the color of the test coating and a specific reference
safety concerns, if any, associated with its use. It is the
coating using colorimetric measurements or by visual compari-
responsibility of the user of this standard to establish appro-
son to the amount of bleeding in a reference photograph.
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
4. Significance and Use
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
4.1 Solvents in a traffic paint may cause bleeding of
ization established in the Decision on Principles for the
pavement constituents into the traffic marking, thereby render-
Development of International Standards, Guides and Recom-
ing the traffic marking less effective as a lane or directional
mendations issued by the World Trade Organization Technical
indicator. This practice describes how to prepare a panel of the
Barriers to Trade (TBT) Committee.
coatingtobetestedandareferencepanelcoatedwithaspecific
solventbornetrafficpainttobeusedasacontrolforevaluation.
2. Referenced Documents
4.2 This practice can be particularly useful for evaluation of
2
2.1 ASTM Standards:
solvent borne traffic paints, but it may also be used for other
D226 Specification forAsphalt-Saturated Organic Felt Used
types of traffic markings including waterborne traffic paints.
in Roofing and Waterproofing
4.3 Two basic procedures are described for measuring the
D227 Specification for Coal-Tar-Saturated Organic Felt
Used in Roofing and Waterproofing amount of bleeding. The procedure used shall be agreed upon
by the purchaser and seller.
D476 Classification for Dry Pigmentary Titanium Dioxide
Products
D1199 Specification for Calcium Carbonate Pigments 5. Apparatus
D2244 Practice for Calculation of Color Tolerances and
5.1 Film Applicator—A conventional type drawdown gage
Color Differences from Instrumentally Measured Color
that casts a film having a minimum width of 50 mm (2 in.) and
Coordinates
an approximate wet thickness of 380 µm (15 mils) (using an
applicator clearance of approximately 760 µm (30 mils)).
5.2 Test Panel for Coal-Tar Substrate—A 127 by 254-mm
(5 by 10-in.) piece cut from a standard roll of so-called “6.8-kg
1
This practice is under the jurisdiction of ASTM Committee D01 on Paint and
(15-lb) coal-tar saturated heat resistant or rag felt.” Unless
Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.44 on Traffic Coatings.
otherwise specified, use a Specification D227 coal tar saturated
Current edition approved Jan. 1, 2021. Published February 2021. Originally
felt.
approved in 1946. Last previous edition approved in 2020 as D868 – 10 (2020).
DOI: 10.1520/D0868-21.
5.3 Test Panel for Asphalt Substrate—A 127 by 254-mm (5
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
by 10-in.) piece cut from a standard roll of 6.8-kg (15-lb)
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
asphalt-saturated felt. Unless otherwise specified, use a Speci-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. fication D226 (Type 1) asphalt saturated felt.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 --
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D868 − 10 (Reapproved 2020) D868 − 21
Standard Practice for
1
Determination of Degree of Bleeding of Traffic Paint
This standard is issued under the fixed designation D868; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice describes test procedures for determining the degree of bleeding of traffic or pavement marking paints. A specific
formulation for a solventborne solvent borne traffic paint formulation is included as a potential bleeding reference control.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D226 Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
D227 Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing
D476 Classification for Dry Pigmentary Titanium Dioxide Products
3
D867 Specification for Pumice Pigment (Withdrawn 1993)
D1199 Specification for Calcium Carbonate Pigments
D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates
1
This practice is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.44 on Traffic Coatings.
Current edition approved June 1, 2020Jan. 1, 2021. Published June 2020February 2021. Originally approved in 1946. Last previous edition approved in 20152020 as
D868 – 10 (2015).(2020). DOI: 10.1520/D0868-10R20.10.1520/D0868-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D868 − 21
E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 bleeding characteristic, n—that condition of discoloration manifested in traffic paint when applied to tar or asphaltic-type
substrates.
3.1.1.1 Discussion—
The amount of discoloration can be comparing the color of the test coating and a specific reference coating using colorimetric
measurements or by visual comparison to the amount of bleeding in a reference photograph.
4. Significance and Use
4.1 Solvents in a traffic paint may cause bleeding of pavement constituents into the traffic marking, thereby rendering the traffic
marking less effective as a lane or directional indicator. This practice describes how to prepare a panel of the coating to be tested
and a reference panel coated with a specific solventborne solvent borne traffic paint to be used as a control for evaluation.
4.2 This practice can be particularly useful for evaluation of solventborne solvent borne traffic paints, but it may also be used for
other types of traffic markings including waterborne traffic paints.
4.3 Two basic procedures are described for measuring the amount of bleeding. The procedure used shall be agreed upon by the
purchaser and seller.
5. Apparatus
5.1 Film Applicator—A conventional type drawdown gage that casts a film having a minimum width of 50 mm (2 in.) and an
approximate wet thickness of 380 μm (15 mils) (using an applicator clearance of approximately 760 μm (30 mils)).
5.2 Test Panel for Coal-Tar Substrate—A 127 by 254-mm (5 by 10-in.) piece cut from a standard roll of so-called “6.8-kg (15-lb)
coal-tar saturat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.