ASTM D5813-04(2018)
(Specification)Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
Standard Specification for Cured-In-Place Thermosetting Resin Sewer Piping Systems
ABSTRACT
This specification covers cured-in-place thermosetting resin pipe (CIPP) with a certain measurement, equivalent diameter, for use in gravity flow systems in conveying sanitary sewage, storm water, and certain industrial wastes. This specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and cure of a resin-impregnated fabric liner. CIPP are classified into three types: Type I which is designed to provide chemical resistance and prevent exfiltration; Type II which is installed in a partially deteriorated existing pipe or structure and is designed to provide chemical resistance, prevent exfiltration and infiltration, and support the external hydrostatic loads due to groundwater only (and internal vacuum, where applicable), since the soil and live loads can be supported by the original conduit or structure; and Type III which is Installed in a fully deteriorated existing pipe or structure and designed to provide chemical resistance, prevent exfiltration and infiltration, and support all external hydraulic, soil, and live loads acting on the original conduit or structure. CIPP also are classified into three grades: Grade 1 as thermosetting polyester resin, Grade 2 as thermosetting polyester resin, and Grade 3 as thermosetting epoxy resin. Properties of CIPP materials such as diameter, wall thickness, chemical resistance, flexural strength, and tensile strength shall be determined by subjecting them to different tests.
SCOPE
1.1 This specification covers cured-in-place thermosetting resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm) equivalent diameter, for use in gravity flow systems for conveying sanitary sewage, storm water, and certain industrial wastes. This specification is suited for the evaluation and testing of materials used in the rehabilitation of existing pipes by the installation and cure of a resin-impregnated fabric liner.
1.2 This specification can also be extended to cover manholes, pump stations, wetwells, vaults, storage tanks, and other similar structures where a cured in place liner using thermosetting resin is applicable.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 1: There are no ISO standards covering the primary subject matter of this specification.
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D5813 −04 (Reapproved 2018) An American National Standard
Standard Specification for
1
Cured-In-Place Thermosetting Resin Sewer Piping Systems
This standard is issued under the fixed designation D5813; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This specification covers cured-in-place thermosetting 2.1 ASTM Standards:
resin pipe (CIPP), 4 through 132-in. (100 through 3353-mm) D543Practices for Evaluating the Resistance of Plastics to
equivalent diameter, for use in gravity flow systems for Chemical Reagents
conveying sanitary sewage, storm water, and certain industrial D638Test Method for Tensile Properties of Plastics
wastes. This specification is suited for the evaluation and D695Test Method for Compressive Properties of Rigid
testing of materials used in the rehabilitation of existing pipes Plastics
by the installation and cure of a resin-impregnated fabric liner. D790Test Methods for Flexural Properties of Unreinforced
and Reinforced Plastics and Electrical Insulating Materi-
1.2 This specification can also be extended to cover
als
manholes, pump stations, wetwells, vaults, storage tanks, and
D883Terminology Relating to Plastics
other similar structures where a cured in place liner using
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
thermosetting resin is applicable.
tics
1.3 The values stated in inch-pound units are to be regarded
D1682Test Method for Breaking Load and Elongation of
3
as standard. The values given in parentheses are mathematical
Textile Fabric (Withdrawn 1992)
conversions to SI units that are provided for information only
D3039/D3039MTest Method forTensile Properties of Poly-
and are not considered standard.
mer Matrix Composite Materials
D3567PracticeforDeterminingDimensionsof“Fiberglass”
NOTE 1—There are no ISO standards covering the primary subject
matter of this specification.
(Glass-Fiber-Reinforced Thermosetting Resin) Pipe and
Fittings
1.4 The following safety hazards caveat pertains only to the
D3681TestMethodforChemicalResistanceof“Fiberglass”
test methods portion, Section 8, of this specification: This
(Glass–Fiber–Reinforced Thermosetting-Resin) Pipe in a
standard does not purport to address all of the safety concerns,
Deflected Condition
if any, associated with its use. It is the responsibility of the user
D4814Specification for Automotive Spark-Ignition Engine
of this standard to establish appropriate safety, health, and
Fuel
environmental practices and determine the applicability of
F412Terminology Relating to Plastic Piping Systems
regulatory limitations prior to use.
F1216Practice for Rehabilitation of Existing Pipelines and
1.5 This international standard was developed in accor-
Conduits by the Inversion and Curing of a Resin-
dance with internationally recognized principles on standard-
Impregnated Tube
ization established in the Decision on Principles for the
F1743Practice for Rehabilitation of Existing Pipelines and
Development of International Standards, Guides and Recom-
ConduitsbyPulled-in-PlaceInstallationofCured-in-Place
mendations issued by the World Trade Organization Technical
Thermosetting Resin Pipe (CIPP)
Barriers to Trade (TBT) Committee.
1 2
This specification is under the jurisdiction ofASTM Committee F17 on Plastic For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Piping Systems and is under the direct responsibility of Subcommittee F17.67 on contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Trenchless Plastic Pipeline Technology. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Oct. 1, 2018. Published October 2018. Originally the ASTM website.
3
approved in 1995. Last previous edition approved in 2012 as D5813–04(2012). The last approved version of this historical standard is referenced on
DOI: 10.1520/D5813-04R18. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D5813 − 04 (2018)
F2019Practice for Rehabilitation of Existing Pipelines and prevent exfiltration and infiltration, and support all external
Conduits by the Pulled in Place Installation of Glass hydraulic, soil, and live loads acting on the original conduit or
Reinforced Plastic (GRP) Cured-in-Place Thermosetting structure.
Resin Pipe (CIPP)
4.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.