ASTM D4747-02(2008)
(Test Method)Standard Test Method for Determining Unreacted Monomer Content of Latexes Using Gas-Liquid Chromatography
Standard Test Method for Determining Unreacted Monomer Content of Latexes Using Gas-Liquid Chromatography
SIGNIFICANCE AND USE
Excessive amounts of unreacted monomer may cause concerns relating to toxicity and odor. This test method is designed to measure the unreacted monomer content of latexes. The results may be used to monitor the extent of polymerization during manufacture, as well as to establish maximum unreacted monomer content for regulatory purposes.
SCOPE
1.1 This test method covers the determination of free monomer content of acrylic latexes. Monomers that have been successfully determined by this procedure include n-butyl methacrylate, n-butyl acrylate, styrene, and methyl methacrylate. The determination of other monomers has not been evaluated, but this test method is believed to be applicable. The established working range of this test method is from 100 to 1000 μg/g, but there is no reason to believe it will not work outside of this range, provided that appropriate dilutions and adjustments in specimen size are made.
1.2 The volatile composition of acrylic latexes is expected to change with time and environmental factors. This time dependence of the determination may be seen as an artificially large deviation of results, making the method mostly applicable for in-house quality control, where sampling and analysis conditions can be better controlled.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Section 7 for specific hazard statements.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4747 − 02(Reapproved 2008)
Standard Test Method for
Determining Unreacted Monomer Content of Latexes Using
1
Gas-Liquid Chromatography
This standard is issued under the fixed designation D4747; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
3
1. Scope Related Materials (Withdrawn 1998)
E260 Practice for Packed Column Gas Chromatography
1.1 This test method covers the determination of free
monomer content of acrylic latexes. Monomers that have been
3. Summary of Test Method
successfully determined by this procedure include n-butyl
3.1 A suitable aliquot of the latex is internally standardized
methacrylate, n-butyl acrylate, styrene, and methyl methacry-
with isobutyl acrylate, diluted with water, and then injected
late. The determination of other monomers has not been
into a gas chromatographic column containing a packing
evaluated,butthistestmethodisbelievedtobeapplicable.The
material coated with a stationary phase that separates the
established working range of this test method is from 100 to
internal standard and monomers in question from each other
1000 µg/g, but there is no reason to believe it will not work
and from other volatile compounds.
outside of this range, provided that appropriate dilutions and
adjustments in specimen size are made.
4. Significance and Use
1.2 The volatile composition of acrylic latexes is expected
4.1 Excessive amounts of unreacted monomer may cause
to change with time and environmental factors. This time
concerns relating to toxicity and odor. This test method is
dependence of the determination may be seen as an artificially
designedtomeasuretheunreactedmonomercontentoflatexes.
large deviation of results, making the method mostly appli-
The results may be used to monitor the extent of polymeriza-
cableforin-housequalitycontrol,wheresamplingandanalysis
tion during manufacture, as well as to establish maximum
conditions can be better controlled.
unreacted monomer content for regulatory purposes.
1.3 The values stated in inch-pound units are to be regarded
5. Apparatus
as the standard. The values given in parentheses are for
5.1 Gas Chromatograph, any gas-liquid chromatographic
information only.
instrument having a flame ionization detector and linear
1.4 This standard does not purport to address all of the
temperature programming.An injection port using replaceable
safety concerns, if any, associated with its use. It is the
glass liners to facilitate periodic removal of accumulated
responsibility of the user of this standard to establish appro-
residues is recommended.
priate safety and health practices and determine the applica-
5.2 Column, 2 by 2-mm inside diameter glass or 6 ft by
bility of regulatory limitations prior to use. See Section 7 for
1
⁄8-in. outside diameter steel tubing, packed with 10 % by
specific hazard statements.
weight of a 2-nitroterephthalic acid derivative of a synthetic
polyester wax on 100/120 mesh acid washed, silane treated
2. Referenced Documents
4
diatomaceous earth. A column of equivalent or superior
2
2.1 ASTM Standards: performance may also be used.
D3980 Practice for Interlaboratory Testing of Paint and
5.3 Recorder—A recording potentiometer with a full-scale
deflection of 10 mV, a full-scale response time of 2 s or less,
and a maximum noise level of 60.03 % of full scale (see
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint Practice E260).
and Related Coatings, Materials, andApplications and is the direct responsibility of
5.4 Liquid Charging Devices, microsyringe, 10-µL capacity
Subcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.
Current edition approved Feb. 1, 2008. Published February 2008. Originally or an automatic liquid sampling device.
approved in 1987. Last previous edition approved in 2002 as D4747 - 02. DOI:
10.1520/D4747-02R08.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or The last approved version of this historical standard is referenced on
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.astm.org.
4
Standards volume information, refer to the standard’s Document Summary page on Columns prepared from the stationary phases and supports have been found
the ASTM website. suitable for this purpose and are available from scientific supply houses.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D4747 − 02 (2008)
5.5 Dropper Pipets, glass, disposable. skin or eye contact with these chemi
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
e1
Designation:D4747–87(Reapproved 1996) Designation:D4747–02(Reapproved2008)
Standard Test Method for
Determining Unreacted Monomer Content of Latexes Using
1
Gas-Liquid Chromatography
This standard is issued under the fixed designation D 4747; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1
e NOTE—Unit of measurement statement added to the Scope Section editorially in May 1997.
1. Scope
1.1 This test method covers the determination of free monomer content of acrylic latexes. Monomers that have been
successfully determined by this procedure include n-butyl methacrylate, n-butyl acrylate, styrene, and methyl methacrylate. The
determinationofothermonomershasnotbeenevaluated,butthistestmethodisbelievedtobeapplicable.Theestablishedworking
range of this test method is from 100 to 1000 µg/g, but there is no reason to believe it will not work outside of this range, provided
that appropriate dilutions and adjustments in specimen size are made.
1.2 Thevolatilecompositionofacryliclatexesisexpectedtochangewithtimeandenvironmentalfactors.Thistimedependence
of the determination may be seen as an artificially large deviation of results, making the method mostly applicable for in-house
quality control, where sampling and analysis conditions can be better controlled.
1.3 The values stated in inch-pound units are to be regarded as the standard.The values given in parentheses are for information
only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. See Section 7 for specific hazard statements.
2. Referenced Documents
2
2.1 ASTM Standards:
3
D 3980 Practice for Interlaboratory Testing of Paint and Related Materials
E 260 Practice for Packed Column Gas Chromatography
3. Summary of Test Method
3.1 A suitable aliquot of the latex is internally standardized with isobutyl acrylate, diluted with water, and then injected into a
gas chromatographic column containing a packing material coated with a stationary phase that separates the internal standard and
monomers in question from each other and from other volatile compounds.
4. Significance and Use
4.1 Excessive amounts of unreacted monomer may cause concerns relating to toxicity and odor. This test method is designed
to measure the unreacted monomer content of latexes. The results may be used to monitor the extent of polymerization during
manufacture, as well as to establish maximum unreacted monomer content for regulatory purposes.
5. Apparatus
5.1 Gas Chromatograph, any gas-liquid chromatographic instrument having a flame ionization detector and linear temperature
programming. An injection port using replaceable glass liners to facilitate periodic removal of accumulated residues is
recommended.
1
This test method is under the jurisdiction of ASTM Committee D-1 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.21 on Chemical Analysis of Paints and Paint Materials .
Current edition approved Nov. 27, 1987. Published January 1988.
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.21 on Chemical Analysis of Paints and Paint Materials .
Current edition approved Feb. 1, 2008. Published February 2008. Originally approved in 1987. Last previous edition approved in 2002 as D 4747 - 02.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
, Vol 06.01.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Withdrawn.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D4747–02 (2008)
1
5.2 Column, 2 by 2-mm inside diameter glass or 6 ft by ⁄8-in. outside diameter steel tubing, packed with 10 % by weight of
4
a2-nitroterephthalicacidderivativeofasyntheticpolyesterwaxon100/120meshacidwashed,silanetreateddiatomaceousearth.
A column of equ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.