iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E3113-18

(Specification)

Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety Agencies

Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety Agencies

SCOPE
1.1 This specification specifies requirements for ballistic-resistant panels to be mounted in or on public safety vehicle doors to protect against complete penetration of projectiles from small arms.2  
1.2 The purpose of this specification is to define minimum performance for ballistic-resistant vehicle door panels.  
1.2.1 In addition to the required tests, optional tests with specific conditions are provided that allow testing beyond the minimum requirements of this specification. Statements of conformance with this specification do not include any optional test unless the optional test is conducted, and the results are included in the test report.  
1.3 This specification requires ballistic testing of vehicle door panels mounted either in a test fixture or mounted on a vehicle door for which the panel is designed.  
1.3.1 Door panels intended to be mounted inside a vehicle door shall be assessed in a test fixture with air backing.
1.3.1.1 Two optional ballistic tests are provided for vehicle door panels intended to be mounted inside a vehicle door:
(1) The preferred optional ballistic test assesses the panel in a vehicle door for which the panel is designed.
(2) If a vehicle door for which the panel is designed is not available, a second optional ballistic test assesses the panel in a test fixture with air backing and a door skin simulant in front of the strike face of the panel.  
1.3.2 Door panels intended to be mounted on the exterior of a vehicle door shall be assessed on a vehicle door for which the panel is designed.  
1.3.3 An optional extreme temperature ballistic test is provided for purchasers concerned with performance of vehicle door panels in very hot or very cold environments.  
1.3.4 The optional ballistic tests are provided in Appendix X1.  
1.4 Selection and procurement guidance is provided in Appendix X2 to assist purchasers in using this specification to procure vehicles with ballistic-resistant door panels or to retrofit existing vehicles with ballistic-resistant door panels.  
1.5 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to non-SI units that are provided for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Oct-2018
ICS
13.310 - Protection against crime
43.020 - Road vehicles in general
Technical Committee
E54 - Homeland Security Applications
Drafting Committee
E54.04 - Public Safety Equipment
Current Stage
Ref Project

Buy Standard

ASTM E3113-18 - Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety AgenciesASTM E3113-18 - Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety Agencies
PreviousNext
Technical specification
ASTM E3113-18 - Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety Agencies
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E3113 − 18
Standard Specification for
Ballistic-resistant Vehicle Door Panels Used by Public
1
Safety Agencies
This standard is issued under the fixed designation E3113; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.4 Selection and procurement guidance is provided in
Appendix X2 to assist purchasers in using this specification to
1.1 This specification specifies requirements for ballistic-
procure vehicles with ballistic-resistant door panels or to
resistant panels to be mounted in or on public safety vehicle
retrofit existing vehicles with ballistic-resistant door panels.
doors to protect against complete penetration of projectiles
2
from small arms. 1.5 Units—The values stated in SI units are to be regarded
as standard. The values given in parentheses are mathematical
1.2 The purpose of this specification is to define minimum
conversions to non-SI units that are provided for information
performance for ballistic-resistant vehicle door panels.
only.
1.2.1 In addition to the required tests, optional tests with
1.6 This standard does not purport to address all of the
specific conditions are provided that allow testing beyond the
safety concerns, if any, associated with its use. It is the
minimum requirements of this specification. Statements of
responsibility of the user of this standard to establish appro-
conformance with this specification do not include any optional
priate safety, health, and environmental practices and deter-
test unless the optional test is conducted, and the results are
mine the applicability of regulatory limitations prior to use.
included in the test report.
1.7 This international standard was developed in accor-
1.3 This specification requires ballistic testing of vehicle
dance with internationally recognized principles on standard-
door panels mounted either in a test fixture or mounted on a
ization established in the Decision on Principles for the
vehicle door for which the panel is designed.
Development of International Standards, Guides and Recom-
1.3.1 Door panels intended to be mounted inside a vehicle
mendations issued by the World Trade Organization Technical
door shall be assessed in a test fixture with air backing.
Barriers to Trade (TBT) Committee.
1.3.1.1 Two optional ballistic tests are provided for vehicle
door panels intended to be mounted inside a vehicle door:
2. Referenced Documents
(1) The preferred optional ballistic test assesses the panel
3
2.1 ASTM Standards:
in a vehicle door for which the panel is designed.
E3005 Terminology for Body Armor
(2) If a vehicle door for which the panel is designed is not
E3062 Specification for Indoor Ballistic Test Ranges for
available, a second optional ballistic test assesses the panel in
Small Arms and Fragmentation Testing of Ballistic-
a test fixture with air backing and a door skin simulant in front
resistant Items
of the strike face of the panel.
E3078 Practice for Conditioning of Hard Armor Test Items
1.3.2 Door panels intended to be mounted on the exterior of
E3112 Test Method for Ballistic-resistant Products and
a vehicle door shall be assessed on a vehicle door for which the
Shoot Packs
panel is designed.
4
1.3.3 An optional extreme temperature ballistic test is pro-
2.2 ISO/IEC Standards:
vided for purchasers concerned with performance of vehicle
ISO/IEC 17050-1 Conformity assessment – Supplier’s dec-
door panels in very hot or very cold environments.
laration of conformity – Part 1: General requirements
1.3.4 The optional ballistic tests are provided in Appendix
ISO/IEC 17050-2 Conformity assessment – Supplier’s dec-
X1.
laration of conformity – Part 2: Supporting documentation
1 3
This specification is under the jurisdiction of ASTM Committee E54 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Homeland Security Applications and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
E54.04 on Personal Protective Equipment (PPE). Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Nov. 1, 2018. Published December 2018. DOI: the ASTM website.
4
10.1520/E3113-18. Available from International Organization for Standardization (ISO), ISO
2
Small arms are defined as portable firearms, typically including handguns, Central Secretariat, BIBC II, Chemin de Blandonnet 8, CP 401, 1214 Vernier,
shotguns, rifles, and light machine guns (Terminology E3005). Geneva, Switzerland, http://www.iso.org.
Copyright © ASTM International, 100 Barr Harbor Drive, P
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E3113-23(Specification)
Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety Agencies

SCOPE
1.1 This specification specifies requirements for ballistic-resistant panels to be mounted in or on public safety vehicle doors to protect against complete penetration of projectiles from small arms.2  
1.2 The purpose of this specification is to define minimum performance for ballistic-resistant vehicle door panels.  
1.2.1 In addition to the required tests, optional tests with specific conditions are provided that allow testing beyond the minimum requirements of this specification. Statements of conformance with this specification do not include any optional test unless the optional test is conducted, and the results are included in the test report.  
1.3 This specification requires ballistic testing of vehicle door panels mounted either in a test fixture or mounted on a vehicle door for which the panel is designed.  
1.3.1 Door panels intended to be mounted inside a vehicle door shall be assessed in a test fixture with air backing.
1.3.1.1 Two optional ballistic tests are provided for vehicle door panels intended to be mounted inside a vehicle door:
(1) The preferred optional ballistic test assesses the panel in a vehicle door for which the panel is designed.
(2) If a vehicle door for which the panel is designed is not available, a second optional ballistic test assesses the panel in a test fixture with air backing and a door skin simulant in front of the strike face of the panel.  
1.3.2 Door panels intended to be mounted on the exterior of a vehicle door shall be assessed on a vehicle door for which the panel is designed.  
1.3.3 An optional extreme temperature ballistic test is provided for purchasers concerned with performance of vehicle door panels in very hot or very cold environments.  
1.3.4 The optional ballistic tests are provided in Appendix X1.  
1.4 Selection and procurement guidance is provided in Appendix X2 to assist purchasers in using this specification to procure vehicles with ballistic-resistant door panels or to retrofit existing vehicles with ballistic-resistant door panels.  
1.5 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to non-SI units that are provided for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM E3113-23(Specification)
Standard Specification for Ballistic-resistant Vehicle Door Panels Used by Public Safety Agencies

SCOPE
1.1 This specification specifies requirements for ballistic-resistant panels to be mounted in or on public safety vehicle doors to protect against complete penetration of projectiles from small arms.2  
1.2 The purpose of this specification is to define minimum performance for ballistic-resistant vehicle door panels.  
1.2.1 In addition to the required tests, optional tests with specific conditions are provided that allow testing beyond the minimum requirements of this specification. Statements of conformance with this specification do not include any optional test unless the optional test is conducted, and the results are included in the test report.  
1.3 This specification requires ballistic testing of vehicle door panels mounted either in a test fixture or mounted on a vehicle door for which the panel is designed.  
1.3.1 Door panels intended to be mounted inside a vehicle door shall be assessed in a test fixture with air backing.
1.3.1.1 Two optional ballistic tests are provided for vehicle door panels intended to be mounted inside a vehicle door:
(1) The preferred optional ballistic test assesses the panel in a vehicle door for which the panel is designed.
(2) If a vehicle door for which the panel is designed is not available, a second optional ballistic test assesses the panel in a test fixture with air backing and a door skin simulant in front of the strike face of the panel.  
1.3.2 Door panels intended to be mounted on the exterior of a vehicle door shall be assessed on a vehicle door for which the panel is designed.  
1.3.3 An optional extreme temperature ballistic test is provided for purchasers concerned with performance of vehicle door panels in very hot or very cold environments.  
1.3.4 The optional ballistic tests are provided in Appendix X1.  
1.4 Selection and procurement guidance is provided in Appendix X2 to assist purchasers in using this specification to procure vehicles with ballistic-resistant door panels or to retrofit existing vehicles with ballistic-resistant door panels.  
1.5 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to non-SI units that are provided for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off