iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6419-00

(Test Method)

Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks

Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks

SCOPE
1.1 This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at 110o+1oC for 60 min.
Note 1--Coldset web offset printing is often (also) referred to as non-heatset web offset printing.
1.2 This test method is also applicable to sheet-fed and coldset web offset printing ink vehicles.
Note 2--Vehicle is the liquid portion of the printing ink. Any substance that is dissolved in the liquid portion of the ink is a part of the vehicle.
1.3 This test method is not applicable to ultra-violet (UV) or electron beam cured materials, which must be cured by exposure to UV light or an electron beam as part of the test for volatile content.
1.4 This test method is based on Test Method D2369, in which the allowable ranges are +0.1g for specimen weight and +5oC for oven temperature. Interlaboratory studies have shown that specimen weight and oven temperature must both be more tightly controlled in order to improve the precision of test results for sheet-fed and coldset web-offset inks. Such inks typically contain a wide range of high-boiling hydrocarbons and often have a volatile content below 25%.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 7.5.1.

General Information

Status
Historical
Publication Date
09-Nov-2000
ICS
59.080.01 - Textiles in general
87.080 - Inks. Printing inks
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.56 - Printing Inks
Current Stage
Ref Project

Relations

Replaces
ASTM D6419-99 - Test Method for Volatile Content of Non-Heatset Web Offset Printing Inks
Effective Date
10-Nov-2000
Replaced By
ASTM D6419-00(2005) - Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
Effective Date
01-Sep-2005
Referred By
ASTM D3960-05(2018) - Standard Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings
Effective Date
10-Nov-2000
Referred By
ASTM D7805-13(2021) - Standard Terminology for Printing Ink Vehicles and Related Materials
Effective Date
10-Nov-2000
Referred By
ASTM D2369-20 - Standard Test Method for Volatile Content of Coatings
Effective Date
10-Nov-2000

Buy Standard

ASTM D6419-00 - Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing InksASTM D6419-00 - Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
PreviousNext
Standard
ASTM D6419-00 - Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6419–00
Test Method for
Volatile Content of Sheet-Fed and Coldset Web Offset
1
Printing Inks
This standard is issued under the fixed designation D 6419; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope E 145 Specification for Gravity-Convection and Forced-
4
Ventilation Ovens
1.1 This test method describes a procedure for determina-
E 691 Practice for Conducting an Interlaboratory Study to
tion of the weight percent volatile content of sheet-fed and
5
Determine the Precision of a Test Method
coldset web offset printing inks. Test specimens are heated at
2.2 Other Standards:
110° 6 1°C for 60 min.
EPA Reference Method 24 - Determination of Volatile
NOTE 1—Coldset web offset printing is often (also) referred to as
Matter Content, Water Content, Density, Volume Solids,
non-heatset web offset printing.
6
and Weight Solids of Surface Coatings
1.2 This test method is also applicable to sheet-fed and
3. Summary of Test Method
coldset web offset printing ink vehicles.
3.1 A specimen size of 0.300 6 0.001 g is weighed into an
NOTE 2—Vehicleistheliquidportionoftheprintingink.Anysubstance
aluminumfoildish,dispersedin3mLoftoluene,andheatedin
that is dissolved in the liquid portion of the ink is a part of the vehicle.
an oven at 110 6 1°C for 60 min. The percent volatile is
1.3 Thistestmethodisnotapplicabletoultra-violet(UV)or
calculated from the loss in weight.
electron beam cured materials, which must be cured by
exposure to UV light or an electron beam as part of the test for
4. Significance and Use
volatile content.
4.1 This test method is the procedure of choice for deter-
1.4 This test method is based on Test Method D 2369, in
mining volatile content of sheet-fed and coldset web offset
which the allowable ranges are 6 0.1g for specimen weight
inks. This information is useful to the ink manufacturer and
and 6 5°C for oven temperature. Interlaboratory studies have
user and to environmental interests as part of the determination
shown that specimen weight and oven temperature must both
of the mass of volatile organic compounds emitted from the
be more tightly controlled in order to improve the precision of
ink.
test results for sheet-fed and coldset web-offset inks. Such inks
NOTE 3—Since these inks do not contain water or any materials
typically contain a wide range of high-boiling hydrocarbons
currently classified by US EPA as negligibly photochemically reactive
and often have a volatile content below 25 %.
(exempt solvents), volatile organic compound content is the same as
1.5 This standard does not purport to address all of the
volatile content. The volatile organic compounds in these inks are high
safety concerns, if any, associated with its use. It is the
boilinghydrocarbonoilswhichare,accordingtoUSEPAguidelines,95 %
responsibility of the user of this standard to establish appro-
retained in the printed substrate or oxidized into the ink film. Therefore,
priate safety and health practices and determine the applica-
the mass of volatile organic compound emitted from the ink would be
calculated as only 5 % of the volatile organic compound content of the ink
bility of regulatory limitations prior to use. For a specific
as derived from the results of this test method.
hazard statement see 7.5.1.
5. Apparatus
2. Referenced Documents
5.1 Aluminum Foil Dishes, 58 mm in diameter by 18 mm
2.1 ASTM Standards:
2
high with a smooth (planar) bottom surface. Precondition the
D 2369 Test Method for Volatile Content of Coatings
3
dishes for 30 min. in an oven at 110 6 1°C and store in a
D 362 Specification for Industrial Grade Toluene
desiccator prior to use. Use tongs or rubber gloves or both, to
handle the dishes.
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint
4
and Related Coatings, Materials, andApplications and is the direct responsibility of Annual Book of ASTM Standards, Vol 14.04.
5
Subcommittee D01.56 on Printing Inks. Annual Book of ASTM Standards, Vol 14.02.
6
Current edition approved Nov. 10, 2000. Published January 2001. Originally Available from the Superintendent of Documents, U.S. Government Printing
published as D 6419–99. Last previous edition D 6419–99. Office, Washington, DC 20402 or Brezinski, J. J., ed., Determination of Volatile
2
Annual Book of ASTM Standards, Vol 06.01. Organic Compound (VOC) Content in Paints, Inks, and Related Coating Products,
3
Annual Book of ASTM Standards, Vol 06.03. MNL 4, ASTM, 1993.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

----------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6419-00(2023)(Test Method)
Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks

SIGNIFICANCE AND USE
4.1 This test method is the procedure of choice for determining volatile content of sheet-fed and coldset web offset inks. This information is useful to the ink manufacturer and user and to environmental interests as part of the determination of the mass of volatile organic compounds emitted from the ink.
Note 3: Since these inks do not contain water or any materials currently classified by US EPA as negligibly photochemically reactive (exempt solvents), volatile organic compound content is the same as volatile content. The volatile organic compounds in these inks are high boiling hydrocarbon oils which are, according to US EPA guidelines, 95 % retained in the printed substrate or oxidized into the ink film. Therefore, the mass of volatile organic compound emitted from the ink would be calculated as only 5 % of the volatile organic compound content of the ink as derived from the results of this test method.
SCOPE
1.1 This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at 110 °C ± 1 °C for 60 min.
Note 1: Coldset web offset printing is often (also) referred to as non-heatset web offset printing.  
1.2 This test method is also applicable to sheet-fed and coldset web offset printing ink vehicles.
Note 2: Vehicle is the liquid portion of the printing ink. Any substance that is dissolved in the liquid portion of the ink is a part of the vehicle.  
1.3 This test method is not applicable to ultra-violet (UV) or electron beam cured materials, which must be cured by exposure to UV light or an electron beam as part of the test for volatile content.  
1.4 This test method is based on Test Method D2369, in which the allowable ranges are ±0.1 g for specimen weight and ±5 °C for oven temperature. Interlaboratory studies have shown that specimen weight and oven temperature must both be more tightly controlled in order to improve the precision of test results for sheet-fed and coldset web-offset inks. Such inks typically contain a wide range of high-boiling hydrocarbons and often have a volatile content below 25 %.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 7.5.1  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6419-00(2023)(Test Method)
Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks

SIGNIFICANCE AND USE
4.1 This test method is the procedure of choice for determining volatile content of sheet-fed and coldset web offset inks. This information is useful to the ink manufacturer and user and to environmental interests as part of the determination of the mass of volatile organic compounds emitted from the ink.
Note 3: Since these inks do not contain water or any materials currently classified by US EPA as negligibly photochemically reactive (exempt solvents), volatile organic compound content is the same as volatile content. The volatile organic compounds in these inks are high boiling hydrocarbon oils which are, according to US EPA guidelines, 95 % retained in the printed substrate or oxidized into the ink film. Therefore, the mass of volatile organic compound emitted from the ink would be calculated as only 5 % of the volatile organic compound content of the ink as derived from the results of this test method.
SCOPE
1.1 This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at 110 °C ± 1 °C for 60 min.
Note 1: Coldset web offset printing is often (also) referred to as non-heatset web offset printing.  
1.2 This test method is also applicable to sheet-fed and coldset web offset printing ink vehicles.
Note 2: Vehicle is the liquid portion of the printing ink. Any substance that is dissolved in the liquid portion of the ink is a part of the vehicle.  
1.3 This test method is not applicable to ultra-violet (UV) or electron beam cured materials, which must be cured by exposure to UV light or an electron beam as part of the test for volatile content.  
1.4 This test method is based on Test Method D2369, in which the allowable ranges are ±0.1 g for specimen weight and ±5 °C for oven temperature. Interlaboratory studies have shown that specimen weight and oven temperature must both be more tightly controlled in order to improve the precision of test results for sheet-fed and coldset web-offset inks. Such inks typically contain a wide range of high-boiling hydrocarbons and often have a volatile content below 25 %.  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 7.5.1  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6390-23(Test Method)
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures

SIGNIFICANCE AND USE
5.1 This test method can be used to determine whether the amount of draindown measured for a given asphalt mixture is within specified acceptable levels. The test provides an evaluation of the draindown potential of an asphalt mixture during mixture design and/or during field production. This test is primarily used for mixtures with high coarse aggregate content such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).
Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers the determination of the amount of draindown in an uncompacted asphalt mixture sample when the sample is held at elevated temperatures comparable to those encountered during the production, storage, transport, and placement of the mixture. The test is particularly applicable to mixtures such as porous asphalt (open-graded friction course) and stone matrix asphalt (SMA).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B472-23(Specification)
Standard Specification for Nickel Alloy Billets and Bars for Reforging

ABSTRACT
This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, and UNS R30556 nickel alloy billets and bars for reforging. The products shall be hot worked from ingots by rolling, forging, extruding, hammering, or pressing. The material shall conform to the chemical composition requirements prescribed by the reference material. The chemical composition of the material shall be determined by chemical analysis in accordance with test method E1473.
SCOPE
1.1 This specification covers UNS N06002, UNS N06030, UNS N06035, UNS N06022, UNS N06200, UNS N10362, UNS N06230, UNS N06600, UNS N06617, UNS N06625, UNS N08020, UNS N08026, UNS N08024, UNS N08120, UNS N08926, UNS N08367, UNS N10242, UNS N10276, UNS N10665, UNS N10675, UNS N12160, UNS R20033, UNS N06059, UNS N06686, UNS N10629, UNS N08031, UNS N06045, UNS N06025, UNS N06699, and UNS R305562 billets and bars for reforging.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    5 pages
    English language
    sale 15% off
  • Technical specification
    5 pages
    English language
    sale 15% off