ASTM C1116/C1116M-06

Standard Specification for Fiber-Reinforced Concrete

SCOPE
1.1 This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed, and that can be sampled and tested at the point of delivery. It does not cover the placement, consolidation, curing, or protection of the fiber-reinforced concrete after delivery to the purchaser.
1.2 Certain sections of this specification are also applicable to fiber-reinforced concrete intended for shotcreting by the dry-mix process when sampling and testing of concrete is possible only at the point of placement. In this case, the sections dealing with batching plant, mixing equipment, mixing and delivery, and measurement of workability and air content, are not applicable.
1.3 This specification does not cover thin-section glass fiber-reinforced concrete manufactured by the spray-up process that is under the jurisdiction of ASTM Subcommittee C27.40.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
The following precautionary statement pertains only to the test method portion, Sections 15 and 18, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 14-Dec-2006
• ICS: 91.100.30 - Concrete and concrete products
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.42 - Fiber-Reinforced Concrete

Relations

• Replaces: ASTM C1116-03 - Standard Specification for Fiber-Reinforced Concrete and Shotcrete
• Effective Date: 15-Dec-2006
• Replaced By: ASTM C1116/C1116M-08 - Standard Specification for Fiber-Reinforced Concrete
• Effective Date: 01-Jan-2008
• Referred By: ASTM C506-22a - Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe
• Effective Date: 15-Dec-2006
• Referred By: ASTM C1818-22 - Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
• Effective Date: 15-Dec-2006
• Referred By: ASTM C118M-19 - Standard Specification for Concrete Pipe for Irrigation or Drainage (Metric)
• Effective Date: 15-Dec-2006
• Referred By: ASTM C14-20 - Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe
• Effective Date: 15-Dec-2006
• Referred By: ASTM C505-19 - Standard Specification for Nonreinforced Concrete Irrigation Pipe with Rubber Gasket Joints
• Effective Date: 15-Dec-2006
• Referred By: ASTM C655-19a - Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
• Effective Date: 15-Dec-2006
• Referred By: ASTM C1731-21 - Standard Specification for Concrete Floor Tile
• Effective Date: 15-Dec-2006
• Referred By: ASTM C505M-19 - Standard Specification for Nonreinforced Concrete Irrigation Pipe With Rubber Gasket Joints (Metric)
• Effective Date: 15-Dec-2006
• Referred By: ASTM C1613-22 - Standard Specification for Precast Concrete Gravity Grease Interceptor Tanks
• Effective Date: 15-Dec-2006
• Referred By: ASTM C1903-21 - Standard Specification for Precast Concrete Duct Bank
• Effective Date: 15-Dec-2006
• Referred By: ASTM C14M-20 - Standard Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)
• Effective Date: 15-Dec-2006
• Referred By: ASTM C1417-19 - Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
• Effective Date: 15-Dec-2006
• Referred By: ASTM C412-19 - Standard Specification for Concrete Drain Tile
• Effective Date: 15-Dec-2006

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 1116/C 1116M – 06
Standard Specification for
1
Fiber-Reinforced Concrete
This standard is issued under the fixed designation C 1116/C 1116M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* A 820/A 820M Specification for Steel Fibers for Fiber-
Reinforced Concrete
1.1 This specification covers all forms of fiber-reinforced
C 31/C 31M Practice for Making and Curing Concrete Test
concrete that are delivered to a purchaser with the ingredients
Specimens in the Field
uniformly mixed, and that can be sampled and tested at the
C 39/C 39M Test Method for Compressive Strength of Cy-
point of delivery. It does not cover the placement, consolida-
lindrical Concrete Specimens
tion, curing, or protection of the fiber-reinforced concrete after
C 42/C 42M Test Method for Obtaining and Testing Drilled
delivery to the purchaser.
Cores and Sawed Beams of Concrete
1.2 Certain sections of this specification are also applicable
C 94/C 94M Specification for Ready-Mixed Concrete
to fiber-reinforced concrete intended for shotcreting by the
C 125 Terminology Relating to Concrete and Concrete
dry-mix process when sampling and testing of concrete is
Aggregates
possible only at the point of placement. In this case, the
C 138/C 138M Test Method for Density (Unit Weight),
sections dealing with batching plant, mixing equipment, mix-
Yield, and Air Content (Gravimetric) of Concrete
ing and delivery, and measurement of workability and air
C 143/C 143M Test Method for Slump of Hydraulic-
content, are not applicable.
Cement Concrete
1.3 This specification does not cover thin-section glass
C 150 Specification for Portland Cement
fiber-reinforcedconcretemanufacturedbythespray-upprocess
C 172 Practice for Sampling Freshly Mixed Concrete
that is under the jurisdiction of ASTM Subcommittee C27.40.
C 173/C 173M Test Method for Air Content of Freshly
1.4 The values stated in either SI units or inch-pound units
Mixed Concrete by the Volumetric Method
are to be regarded separately as standard. The values stated in
C 192/C 192M Practice for Making and Curing Concrete
each system may not be exact equivalents; therefore, each
Test Specimens in the Laboratory
system shall be used independently of the other. Combining
C 231 Test Method for Air Content of Freshly Mixed
values from the two systems may result in non-conformance
Concrete by the Pressure Method
with the standard.
C 387 SpecificationforPackaged,Dry,CombinedMaterials
1.5 The following precautionary statement pertains only to
for Mortar and Concrete
the test method portion, Sections 15 and 18, of this specifica-
C 567 Test Method for Determining Density of Structural
tion: This standard does not purport to address all of the safety
Lightweight Concrete
concerns, if any, associated with its use. It is the responsibility
C 666/C 666M Test Method for Resistance of Concrete to
of the user of this standard to establish appropriate safety and
Rapid Freezing and Thawing
health practices and determine the applicability of regulatory
C 684 Test Method for Making, Accelerated Curing, and
limitations prior to use.
Testing Concrete Compression Test Specimens
2. Referenced Documents
C 685/C 685M Specification for Concrete Made by Volu-
2
metric Batching and Continuous Mixing
2.1 ASTM Standards:
C 887 SpecificationforPackaged,Dry,CombinedMaterials
for Surface Bonding Mortar
C 995 Test Method for Time of Flow of Fiber-Reinforced
1
This specification is under the jurisdiction of ASTM Committee C09 on
Concrete Through Inverted Slump Cone
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee
C 1077 PracticeforLaboratoriesTestingConcreteandCon-
C09.42 on Fiber-Reinforced Concrete.
crete Aggregates for Use in Construction and Criteria for
Current edition approved Dec. 15, 2006. Published January 2007. Originally
approved in 1989. Last previous edition approved in 2003 as C 1116 – 03.
Laboratory Evaluation
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
C 1140 Practice for Preparing and Testing Specimens from
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Shotcrete Test Panels
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
C 1116/C 1116M – 06
detrimen
...