ASTM C1613-22
(Specification)Standard Specification for Precast Concrete Gravity Grease Interceptor Tanks
Standard Specification for Precast Concrete Gravity Grease Interceptor Tanks
ABSTRACT
This specification covers design requirements, manufacturing practices, and performance requirements for monolithic or sectional precast concrete grease interceptor tanks. This standard describes precast concrete tanks installed to separate fats, oils, grease, soap scum, and other typical kitchen wastes associated with the food service industry. The different materials and manufacturing practices of precast concrete grease interceptor tanks are presented in details. Structural design of grease interceptor tanks shall be by calculation or by performance. The different structural design requirement of grease interceptor tanks includes; concrete strength, reinforcing steel placement, and openings. The different physical design requirements of grease interceptor tanks includes; capacity, shape, compartments, inlet and outlet pipes, baffles and outlet devices, and top slab openings. Testing for watertightness shall be performed using either vacuum testing or hydrostatic testing.
SCOPE
1.1 This specification covers design requirements, manufacturing practices, and performance requirements for monolithic or sectional precast concrete grease interceptor tanks.
1.2 This specification describes precast concrete tanks installed to separate fats, oils, grease, soap scum, and other typical kitchen wastes associated with the food service industry.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1613 −22
Standard Specification for
1
Precast Concrete Gravity Grease Interceptor Tanks
This standard is issued under the fixed designation C1613; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Welded Wire Reinforcement, Plain and Deformed, for
Concrete
1.1 This specification covers design requirements, manufac-
C33/C33M Specification for Concrete Aggregates
turing practices, and performance requirements for monolithic
C39/C39M Test Method for Compressive Strength of Cylin-
or sectional precast concrete grease interceptor tanks.
drical Concrete Specimens
1.2 This specification describes precast concrete tanks in-
C94/C94M Specification for Ready-Mixed Concrete
stalled to separate fats, oils, grease, soap scum, and other
C125 Terminology Relating to Concrete and Concrete Ag-
typical kitchen wastes associated with the food service indus-
gregates
try.
C150/C150M Specification for Portland Cement
C260/C260M Specification for Air-Entraining Admixtures
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical for Concrete
C330/C330M Specification for Lightweight Aggregates for
conversions to SI units that are provided for information only
and are not considered standard. Structural Concrete
C494/C494M Specification for Chemical Admixtures for
1.4 This standard does not purport to address all of the
Concrete
safety concerns, if any, associated with its use. It is the
C595/C595M Specification for Blended Hydraulic Cements
responsibility of the user of this standard to establish appro-
C618 Specification for Coal Fly Ash and Raw or Calcined
priate safety, health, and environmental practices and deter-
Natural Pozzolan for Use in Concrete
mine the applicability of regulatory limitations prior to use.
C685/C685M Specification for Concrete Made by Volumet-
1.5 This international standard was developed in accor-
ric Batching and Continuous Mixing
dance with internationally recognized principles on standard-
C890 Practice for Minimum Structural Design Loading for
ization established in the Decision on Principles for the
Monolithic or Sectional Precast Concrete Water and
Development of International Standards, Guides and Recom-
Wastewater Structures
mendations issued by the World Trade Organization Technical
C923/C923M Specification for Resilient Connectors Be-
Barriers to Trade (TBT) Committee.
tween Reinforced Concrete Manhole Structures, Pipes,
and Laterals
2. Referenced Documents
C990 Specification for Joints for Concrete Pipe, Manholes,
2
2.1 ASTM Standards:
and Precast Box Sections Using Preformed Flexible Joint
A184/A184M Specification for Welded Deformed Steel Bar
Sealants
Mats for Concrete Reinforcement
C1116/C1116M Specification for Fiber-Reinforced Concrete
A615/A615M SpecificationforDeformedandPlainCarbon-
C1602/C1602M Specification for Mixing Water Used in the
Steel Bars for Concrete Reinforcement
Production of Hydraulic Cement Concrete
A706/A706M Specification for Deformed and Plain Low-
3
2.2 ACI Standard:
Alloy Steel Bars for Concrete Reinforcement
ACI 318 Building Code Requirements for Reinforced Con-
A1064/A1064M Specification for Carbon-Steel Wire and
crete
4
2.3 IAPMO Documents:
1
This specification is under the jurisdiction ofASTM Committee C27 on Precast
Uniform Plumbing Code
ConcreteProductsandisthedirectresponsibilityofSubcommitteeC27.30onWater
IAPMO PS-80 Grease Interceptors and Clarifiers
and Wastewater Containers.
Current edition approved Jan. 1, 2022. Published January 2022. Originally
approved in 2006. Last previous edition approved in 2017 as C1613 – 17. DOI:
10.1520/C1613-22.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Hills, MI 48333-9094, http://www.concrete.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from InternationalAssociation of Plumbing and Mechanical Officials
the ASTM website. (IAPMO), 5001 E. Philadelphia St., Ontario, CA 91761, http://www.iapmo.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1613 − 22
5
2.4 AASHTO Standard: 4.1.3 Capacity of tank in gallons or litres.
Standard Specification
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1613 − 17 C1613 − 22
Standard Specification for
1
Precast Concrete Gravity Grease Interceptor Tanks
This standard is issued under the fixed designation C1613; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers design requirements, manufacturing practices, and performance requirements for monolithic or
sectional precast concrete grease interceptor tanks.
1.2 This specification describes precast concrete tanks installed to separate fats, oils, grease, soap scum, and other typical kitchen
wastes associated with the food service industry.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A184/A184M Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
C33C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C94/C94M Specification for Ready-Mixed Concrete
C125 Terminology Relating to Concrete and Concrete Aggregates
C150C150/C150M Specification for Portland Cement
C260C260/C260M Specification for Air-Entraining Admixtures for Concrete
C330C330/C330M Specification for Lightweight Aggregates for Structural Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C595C595/C595M Specification for Blended Hydraulic Cements
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
and Wastewater Containers.
Current edition approved Sept. 1, 2017Jan. 1, 2022. Published September 2017January 2022. Originally approved in 2006. Last previous edition approved in 20102017
as C1613 – 10.C1613 – 17. DOI: 10.1520/C1613-17.10.1520/C1613-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1613 − 22
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C685/C685M Specification for Concrete Made by Volumetric Batching and Continuous Mixing
C890 Practice for Minimum Structural Design Loading for Monolithic or Sectional Precast Concrete Water and Wastewater
Structures
C923C923/C923M Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and
Laterals (Metric) C0923_C0923M
C990 Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
C1116C1116/C1116M Specification for Fiber-Reinforced Concrete
C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
3
2.2 ACI Standard:
ACI 318 Building Code Requirements for Reinforced Concrete
4
2.3 IAPMO Documents:
Uniform Plumbing Code
IAPMO PS-80 Grease Interceptors and Clarifiers
5
2.4 AASHTO Standard:
Standard Specifications for Highway Bridges
3. Terminology
3.1 For definitions of terms relating to concrete, see T
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1613 − 22
Standard Specification for
1
Precast Concrete Gravity Grease Interceptor Tanks
This standard is issued under the fixed designation C1613; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Welded Wire Reinforcement, Plain and Deformed, for
Concrete
1.1 This specification covers design requirements, manufac-
C33/C33M Specification for Concrete Aggregates
turing practices, and performance requirements for monolithic
C39/C39M Test Method for Compressive Strength of Cylin-
or sectional precast concrete grease interceptor tanks.
drical Concrete Specimens
1.2 This specification describes precast concrete tanks in-
C94/C94M Specification for Ready-Mixed Concrete
stalled to separate fats, oils, grease, soap scum, and other
C125 Terminology Relating to Concrete and Concrete Ag-
typical kitchen wastes associated with the food service indus-
gregates
try.
C150/C150M Specification for Portland Cement
1.3 The values stated in inch-pound units are to be regarded C260/C260M Specification for Air-Entraining Admixtures
for Concrete
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only C330/C330M Specification for Lightweight Aggregates for
Structural Concrete
and are not considered standard.
C494/C494M Specification for Chemical Admixtures for
1.4 This standard does not purport to address all of the
Concrete
safety concerns, if any, associated with its use. It is the
C595/C595M Specification for Blended Hydraulic Cements
responsibility of the user of this standard to establish appro-
C618 Specification for Coal Fly Ash and Raw or Calcined
priate safety, health, and environmental practices and deter-
Natural Pozzolan for Use in Concrete
mine the applicability of regulatory limitations prior to use.
C685/C685M Specification for Concrete Made by Volumet-
1.5 This international standard was developed in accor-
ric Batching and Continuous Mixing
dance with internationally recognized principles on standard-
C890 Practice for Minimum Structural Design Loading for
ization established in the Decision on Principles for the
Monolithic or Sectional Precast Concrete Water and
Development of International Standards, Guides and Recom-
Wastewater Structures
mendations issued by the World Trade Organization Technical
C923/C923M Specification for Resilient Connectors Be-
Barriers to Trade (TBT) Committee.
tween Reinforced Concrete Manhole Structures, Pipes,
and Laterals
2. Referenced Documents
C990 Specification for Joints for Concrete Pipe, Manholes,
2
2.1 ASTM Standards:
and Precast Box Sections Using Preformed Flexible Joint
A184/A184M Specification for Welded Deformed Steel Bar
Sealants
Mats for Concrete Reinforcement
C1116/C1116M Specification for Fiber-Reinforced Concrete
A615/A615M Specification for Deformed and Plain Carbon-
C1602/C1602M Specification for Mixing Water Used in the
Steel Bars for Concrete Reinforcement
Production of Hydraulic Cement Concrete
A706/A706M Specification for Deformed and Plain Low-
3
2.2 ACI Standard:
Alloy Steel Bars for Concrete Reinforcement
ACI 318 Building Code Requirements for Reinforced Con-
A1064/A1064M Specification for Carbon-Steel Wire and
crete
4
2.3 IAPMO Documents:
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast
Uniform Plumbing Code
Concrete Products and is the direct responsibility of Subcommittee C27.30 on Water
IAPMO PS-80 Grease Interceptors and Clarifiers
and Wastewater Containers.
Current edition approved Jan. 1, 2022. Published January 2022. Originally
approved in 2006. Last previous edition approved in 2017 as C1613 – 17. DOI:
10.1520/C1613-22.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Hills, MI 48333-9094, http://www.concrete.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from International Association of Plumbing and Mechanical Officials
the ASTM website. (IAPMO), 5001 E. Philadelphia St., Ontario, CA 91761, http://www.iapmo.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1613 − 22
5
2.4 AASHTO Standard: 4.1.3 Capacity of tank in gallons or litres.
Standard Specifications for Highway Bridges 4.1.4 Special cement requirements including moderate
sulfate-resisting cement, Specificatio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.