ASTM F2763-16

Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

ABSTRACT
This specification covers requirements and test methods for triple profile wall polyethylene pipe and fittings. The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. This specification covers pipe and fittings with an essentially smooth interior and exterior wall using an annular corrugated profile middle wall.
SCOPE
1.1 This specification covers requirements and test methods for dual and triple profile wall polyethylene pipe and fittings. The nominal inside diameters covered are 12 to 60 in. [300 to 1500 mm].  
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321.  
1.3 This specification covers pipe and fittings with an essentially smooth interior wall and either an annular corrugation (dual wall) or an essentially smooth and exterior wall using an annular corrugated profile middle wall (triple wall) (Fig. 1).  
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Jan-2016
• ICS: 91.140.80 - Drainage systems
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.62 - Sewer

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2763 −16
Standard Specification for
12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall
Polyethylene (PE) Pipe and Fittings for Sanitary Sewer
1
Applications
This standard is issued under the fixed designation F2763; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A666Specification forAnnealed or Cold-WorkedAustenitic
Stainless Steel Sheet, Strip, Plate, and Flat Bar
1.1 This specification covers requirements and test methods
D618Practice for Conditioning Plastics for Testing
for dual and triple profile wall polyethylene pipe and fittings.
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
The nominal inside diameters covered are 12 to 60 in. [300 to
tics
1500 mm].
D2122Test Method for Determining Dimensions of Ther-
1.2 The requirements of this specification are intended to
moplastic Pipe and Fittings
provide pipe and fittings suitable for underground use for
D2321PracticeforUndergroundInstallationofThermoplas-
non-pressure sanitary sewer systems. Pipe and fittings pro-
tic Pipe for Sewers and Other Gravity-Flow Applications
ducedinaccordancewiththisspecificationshallbeinstalledin
D2412Test Method for Determination of External Loading
compliance with Practice D2321.
Characteristics of Plastic Pipe by Parallel-Plate Loading
1.3 This specification covers pipe and fittings with an
D2444Test Method for Determination of the Impact Resis-
essentially smooth interior wall and either an annular corruga-
tance of Thermoplastic Pipe and Fittings by Means of a
tion (dual wall) or an essentially smooth and exterior wall
Tup (Falling Weight)
using an annular corrugated profile middle wall (triple wall)
D3212Specification for Joints for Drain and Sewer Plastic
(Fig. 1).
Pipes Using Flexible Elastomeric Seals
1.4 Units—The values stated in either SI units or inch-
D3350Specification for Polyethylene Plastics Pipe and Fit-
pound units are to be regarded separately as standard. The
tings Materials
values stated in each system may not be exact equivalents;
D4218Test Method for Determination of Carbon Black
therefore,eachsystemshallbeusedindependentlyoftheother.
Content in Polyethylene Compounds By the Muffle-
Combining values from the two systems may result in non-
Furnace Technique
conformance with the standard.
F412Terminology Relating to Plastic Piping Systems
1.5 The following precautionary caveat pertains only to the
F477Specification for Elastomeric Seals (Gaskets) for Join-
test method portion, Section 7, of this specification. This
ing Plastic Pipe
standard does not purport to address all of the safety concerns,
F2136Test Method for Notched, Constant Ligament-Stress
if any, associated with its use. It is the responsibility of the user
(NCLS) Test to Determine Slow-Crack-Growth Resis-
of this standard to establish appropriate safety and health
tance of HDPE Resins or HDPE Corrugated Pipe
practices and determine the applicability of regulatory limita-
3
tions prior to use. 2.2 AASHTO Standard:
LRFD, Section 12AASHTO LRFD Bridge Design Specifi-
2. Referenced Documents
cations Section 12 – Buried Structures and Tunnel Liners
2
2.1 ASTM Standards:
4
2.3 Federal Standards:
D578/D578MSpecification for Glass Fiber Strands
Fed. Std. No. 123Marking for Shipment (Civil Agencies)
MIL-STD-129Marking for Shipment and Storage
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Current edition approved Feb. 1, 2016. Published April 2016. Originally
approved in 2011. Last previous edition approved in 2011 as F2763–11. DOI:
3
10.1520/F2763–16. Available from American Association of State Highway and Transportation
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Officials (AASHTO), 444 N. Capitol St., NW, Suite 249, Washington, DC 20001,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM http://www.transportation.org.
4
Standards volume information, refer to the standard’s Document Summary page on DLA Document Services Building 4/D 700 Robbins Avenue Philadelphia, PA
the ASTM website. 19111-5094 http://quicksearch.dla.mil/
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2763−16
FIG. 1Typical Dual and Triple Wall Pipe Profile
2.4 NCHRP (National Cooperative Highway Research Pro- 4.1.2 Diameters,
4
gram) Report: 4.1.3 Total footage of each pipe diameter involved,
NCHRP Report 631Updated Test and Design Methods for 4.1.4 Pipe laying length,
T
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2763 − 11 F2763 − 16
Standard Specification for
3012 to 60 in. [750[300 to 1500 mm] Dual and Triple Profile-
Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer
1
Applications
This standard is issued under the fixed designation F2763; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers requirements and test methods for dual and triple profile wall polyethylene pipe and fittings. The
nominal inside diameters covered are 3012 to 60 in. [750[300 to 1500 mm].
1.2 The requirements of this specification are intended to provide pipe and fittings suitable for underground use for non-pressure
sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with
Practice D2321.
1.3 This specification covers pipe and fittings with an essentially smooth interior and wall and either an annular corrugation
(dual wall) or an essentially smooth and exterior wall using an annular corrugated profile middle wall (triple wall) (Fig. 1).
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D578/D578M Specification for Glass Fiber Strands
A666 Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling
Weight)
D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218 Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
D4389 Specification for Finished Glass Fabrics Woven From Rovings
F412 Terminology Relating to Plastic Piping Systems
F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe
F2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE
Resins or HDPE Corrugated Pipe
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.62 on Sewer.
Current edition approved Feb. 1, 2011Feb. 1, 2016. Published February 2011April 2016. Originally approved in 2011. Last previous edition approved in 2011 as F2763–11.
DOI: 10.1520/F2763–11.10.1520/F2763–16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2763 − 16
FIG. 1 Typical Dual and Triple Wall Pipe Profile
3
2.2 AASHTO Standard:
LRFD, Section 12 AASHTO LRFD Bridge Design Specifications Section 12 – Buried Structures and Tunnel Liners
4
2.3 Federal Standards:
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
MIL-STD-129 Marking for Shipment and Storage
4
2.4 NCHRP (National Cooperative Highway Research Program) Report
...