iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3934-20

(Test Method)

Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus

Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus

SIGNIFICANCE AND USE
5.1 This test method ensures that before the flash test is run the air/vapor space above the specimen has attained a saturation concentration of vapor by using standard closed cups under equilibrium conditions. The saturation concentration of the vapors will be attained at some temperature between that of the liquid and the cooler apparatus lid. However, this temperature will be close to the temperature of the specimen after it has been maintained at the specified temperature for at least a 10-min period. This test method does not provide for the determination of the actual flash point but only whether a specimen does or does not flash at a specified temperature.
SCOPE
1.1 This test method covers the determination of whether a liquid complies with the closed-cup flash point requirements in government regulations, or in specifications, or as agreed between the purchaser and the seller.  
1.2 This test method is limited to a temperature range between 0 and 110°C (32 and 230°F).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national law. Users must determine legality of sales in their location.  
1.5 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-May-2020
ICS
87.040 - Paints and varnishes
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.21 - Chemical Analysis of Paints and Paint Materials
Current Stage
Ref Project

Relations

Refers
ASTM D3941-20 - Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus
Effective Date
01-Jun-2020
Refers
ASTM D93-20 - Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
Effective Date
01-Aug-2020
Referred By
ASTM E502-21a - Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods
Effective Date
01-Jun-2020

Buy Standard

ASTM D3934-20 - Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup ApparatusASTM D3934-20 - Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus
PreviousNext
Standard
ASTM D3934-20 - Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D3934-20 - Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup ApparatusREDLINE ASTM D3934-20 - Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus
PreviousNext
Standard
REDLINE ASTM D3934-20 - Standard Test Method for Flash/No Flash Test—Equilibrium Method by a Closed-Cup Apparatus
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3934 − 20
Standard Test Method for
Flash/No Flash Test—Equilibrium Method by a Closed-Cup
1
Apparatus
This standard is issued under the fixed designation D3934; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
ASTM Flash Point Test Methods D56, D93, D3278, and D3941 are specified by government
departments and agencies for determining whether liquids are flammable or combustible. These
classifications are used as the basis for regulating the handling and shipping of liquids.
ISO/TC35,PaintsandVarnishes,andISO/TC28,PetroleumandRelatedProducts,haveissuedISO
1516 as a common standard, applicable to paints, varnishes, petroleum, and related products. This
method is similar to ISO 1516 but uses standard ASTM cups and style and format. Test Methods
D3278 and D3828 operate on the equilibrium principle by using the Setaflash tester that has a
temperature-control device.
This test method does not determine the finite flash point but whether or not flashing occurs at a
single specified temperature. The latter determination is made more accurate by ensuring that the test
is carried out only when the material under test and the air/vapor mixture above it are in approximate
equilibrium at the specified temperature.
1. Scope is prohibited by local or national law. Users must determine
legality of sales in their location.
1.1 This test method covers the determination of whether a
1.5 This standard is used to measure and describe the
liquid complies with the closed-cup flash point requirements in
response of materials, products, or assemblies to heat and
government regulations, or in specifications, or as agreed
flame under controlled conditions, but does not by itself
between the purchaser and the seller.
incorporate all factors required for fire hazard or fire risk
1.2 This test method is limited to a temperature range
assessment of the materials, products, or assemblies under
between 0 and 110°C (32 and 230°F).
actual fire conditions.
1.3 The values stated in inch-pound units are to be regarded 1.6 This standard does not purport to address all of the
as standard. The values given in parentheses are mathematical safety concerns, if any, associated with its use. It is the
conversions to SI units that are provided for information only responsibility of the user of this standard to establish appro-
and are not considered standard. priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
1.4 Warning—Mercury has been designated by many regu-
1.7 This international standard was developed in accor-
latory agencies as a hazardous substance that can cause
dance with internationally recognized principles on standard-
serious medical issues. Mercury, or its vapor, has been
ization established in the Decision on Principles for the
demonstrated to be hazardous to health and corrosive to
Development of International Standards, Guides and Recom-
materials. Use caution when handling mercury and mercury-
mendations issued by the World Trade Organization Technical
containing products. See the applicable product Safety Data
Barriers to Trade (TBT) Committee.
Sheet (SDS) for additional information. The potential exists
that selling mercury or mercury-containing products, or both,
2. Referenced Documents
2
2.1 ASTM Standards:
D56 Test Method for Flash Point by Tag Closed Cup Tester
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
2
ASTM Subcommittee D01.21 on Chemical Analysis of Paints and Paint Materials. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 1, 2020. Published June 2020. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1982. Last previous edition approved in 2014 as D3934 – 14. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D3934-20. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3934 − 20
NOTE 1—If a stirrer is fitted to the test cup, it shall be operated during
D93 Test Methods for Flash Point by Pensky-Martens
the heating period but must be stopped during the flashing determination.
Close
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3934 − 14 D3934 − 20
Standard Test Method for
Flash/No Flash Test—Equilibrium Method by a Closed-Cup
1
Apparatus
This standard is issued under the fixed designation D3934; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
ASTM Flash Point Test Methods D56, D93, D3278, and D3941 are specified by government
departments and agencies for determining whether liquids are flammable or combustible. These
classifications are used as the basis for regulating the handling and shipping of liquids.
ISO/TC 35, Paints and Varnishes, and ISO/TC 28, Petroleum and Related Products, have issued ISO
1516 as a common standard, applicable to paints, varnishes, petroleum, and related products. This
method is similar to ISO 1516 but uses standard ASTM cups and style and format. Test Methods
D3278 and D3828 operate on the equilibrium principle by using the Setaflash tester that has a
temperature-control device.
This test method does not determine the finite flash point but whether or not flashing occurs at a
single specified temperature. The latter determination is made more accurate by ensuring that the test
is carried out only when the material under test and the air/vapor mixture above it are in approximate
equilibrium at the specified temperature.
1. Scope*Scope
1.1 This test method covers the determination of whether a liquid complies with the closed-cup flash point requirements in
government regulations, or in specifications, or as agreed between the purchaser and the seller.
1.2 This test method is limited to a temperature range between 0 and 110°C (32 and 230°F).
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious
medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Use caution
when handling mercury and mercury-containing products. See the applicable product Safety Data Sheet (SDS) for additional
information. The potential exists that selling mercury or mercury-containing products, or both, is prohibited by local or national
law. Users must determine legality of sales in their location.Warning—Mercury has been designated by many regulatory agencies
as a hazardous material that can cause central nervous system, kidney and liver damage. Mercury, or its vapor, may be hazardous
to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the
applicable product Safety Data Sheet (SDS) for details and EPA’s website, http://www.epa.gov/mercury/faq.htm, for additional
information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be
prohibited by law.
1.5 This standard should be is used to measure and describe the propertiesresponse of materials, products, or assemblies in
response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise theconditions,
but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies
under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account
all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.
1
This test method is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of ASTM
Subcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.
Current edition approved Dec. 15, 2014June 1, 2020. Published January 2015June 2020. Originally approved in 1982. Last previous edition approved in 20072014 as
D3934 – 90 (2007).D3934 – 14. DOI: 10.1520/D3934-14.10.1520/D3934-20.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D3934 − 20
1.6 This stand
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D16-23(Terminology)
Standard Terminology for Paint, Related Coatings, Materials, and Applications

SCOPE
1.1 This standard consists of technical terms used in standards under the jurisdiction of ASTM Committee D01 (on Paint and Related Coatings, Materials, and Applications), and of definitions suitable for use in these standards.
Note 1: When any definition in this standards is quoted or published out of the context of this standard, editorially insert the following delimiting statement “for paints and related coatings, materials, and applications” after the dash following the term (in the absence of an existing delimiting statement). This will limit the filed of application of the term and definition to that approved by this committee.  
1.2 In this terminology standard, definitions used in other ASTM standards are indicated by following the definition with the designation of that standard. In some cases, a relevant D01 subcommittee is also listed. Definitions influenced by those used by other organizations are indicated by the acronym of the organization. Primary terms are given in bold, while narrower and unapproved terms are given in italics.  
1.3 There are several specialized terminology standards under the jurisdiction of Committee D01, as follows: D804, D1695, D6440, D6488, and D7188. Few definitions from those standards are included in Terminology D16. Therefore, in searches for definitions of paints and coatings terms, these standards should be included where appropriate.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D3322-23(Practice)
Standard Practice for Testing Primers and Primer Surfacers Over Preformed Metal

SIGNIFICANCE AND USE
4.1 Primers and primer surfacers may be used over many different surfaces top coated with one or more of a variety of coatings and subjected to many kinds of wear and exposure.  
4.2 The selection of the tests to be used for any given product or system must be governed by experience and by the requirement agreed upon between the producer and the user.
SCOPE
1.1 This practice covers the selection and use of procedures for testing primers and primer surfacers.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D2805-11(2023)(Test Method)
Standard Test Method for Hiding Power of Paints by Reflectometry

SIGNIFICANCE AND USE
5.1 This is a precise instrumental method giving results having an absolute physical significance without reference to a comparison paint. It should be used when maximum precision and minimum subjectivity are required, as in testing specification coatings or evaluating the hiding efficiency of pigments.  
5.2 Hiding power Test Method D344 is visual instead of instrumental, and gives results that are relative to a material standard instead of absolute. It is less precise than Test Method D2805 but more closely aligned with practical painting procedures.
SCOPE
1.1 This test method covers the determination, without reference to a material paint standard, of the hiding power of air dry coatings with Y tristimulus values greater than 15 %. With appropriate modification, it can also be used to test baking finishes.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D1644-01(2023)(Test Method)
Standard Test Methods for Nonvolatile Content of Varnishes

SIGNIFICANCE AND USE
2.1 These test methods are applicable to varnish and are useful to producers and users in determining nonvolatile content and are sometimes an appropriate measure of the film-forming matter in varnish.
SCOPE
1.1 These test methods determine the fraction of a varnish that is nonvolatile at the temperature of the test while volatile solvents are driven off. It is sometimes an approximate measure of the film-forming matter in a varnish.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific statement, see Section 3.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6486-23(Practice)
Standard Practice for Short Term Vehicle Service Exposure of Automotive Coatings

SIGNIFICANCE AND USE
4.1 Since the exposure of automotive coatings to the various mechanical and chemical stresses encountered in actual operations, is very opportunistic, obtaining statistically significant data from which valid conclusions can be drawn, requires rigorous attention to the experimental designs and conditions of exposure.
SCOPE
1.1 This practice covers the protocol for vehicle service exposure testing of automotive coatings. Such exposure testing is valuable for the verification of the performance of automotive coatings and correlation with laboratory test data. Vehicle service exposure is intended to provide short term (2 to 20 weeks) exposure to the stress factors associated with vehicle operation. Factors included are scratch, mar, impact, stone chipping, insect impact, bird dropping, tree sap and staining, environmental fallout, etc.
Note 1: Vehicle service exposure is not intended to provide the conditions that are needed for characterizing the long term effects of weathering or corrosion exposure.  
1.2 The exposure conditions are produced by the placement of multiple test panels of automotive finishes on automotive test fleets that traverse a defined road course. Exposure to the operating environment can be 20 h/day, 7 days/week allowing for accumulation of over 100 000 miles in 10 weeks of exposure.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6762-18(2023)(Test Method)
Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings

SIGNIFICANCE AND USE
5.1 This test method determines hiding power of a test paint by visual evaluation of a spray applied coating.
Note 1: Test Method D2805 describes an instrumental method for determining hiding power. The paint film is applied at a uniform thickness (for example with a doctor blade), the film thickness is measured rigorously, and the opacity is determined photometrically. Hiding power is thereby determined with a high degree of precision.  
5.2 Test Method D6762 is less precise than Test Method D2805, but is commonly used since it is more closely related to the application characteristics of the paint and is simpler in concept and evaluation.
SCOPE
1.1 This test method provides for the quantitative visual determination of the film thickness required to achieve full hiding. This film thickness is considered to be the hiding power of a test paint.  
1.2 This method applies only to spray applied coatings but its concepts are valid for other methods of application as well.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3732-23(Practice)
Standard Practice for Reporting Cure Times of Ultraviolet-Cured Coatings

SIGNIFICANCE AND USE
4.1 This practice provides a guide whereby all pertinent variables relating to the ultraviolet cure of a coating are described.
SCOPE
1.1 This practice applies to all coatings cured by ultraviolet energy.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D713-23(Practice)
Standard Practice for Conducting Road Service Tests on Fluid Traffic Marking Materials

SIGNIFICANCE AND USE
3.1 This practice is an accelerated evaluation of bead retention, retroreflectivity, daytime color, night time color, and wear characteristics of fluid traffic marking materials. It is used to determine the useful life of such markings in the field. The same procedures are applicable to evaluating longitudinal lines to determine service life.
SCOPE
1.1 This practice covers the determination of the relative service life of fluid traffic marking materials such as paint, thermoplastic, epoxy, and polyester products under actual road conditions using transverse test lines. Materials under test are applied under prescribed conditions and periodic observations are made using prescribed performance criteria.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D3891-23(Practice)
Standard Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products

SIGNIFICANCE AND USE
3.1 The procedures described in this practice are designed to provide uniform glass panels for testing of paint, varnish, lacquer, conversion coatings and related products.
SCOPE
1.1 This practice covers the preparation of glass panels for subsequent testing of paint, varnish, lacquer, and related products.2  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D2201-23(Practice)
Standard Practice for Preparation of Zinc-Coated and Zinc-Alloy-Coated Steel Panels for Testing Paint and Related Coating Products

SIGNIFICANCE AND USE
3.1 The procedures described in this practice are designed to provide uniform zinc coated steel panels for testing of paint, varnish, lacquer, conversion coatings and related products.  
3.2 The proper description of the zinc coating on the substrate is an important part of this practice. Seemingly slight differences in zinc coating can produce substantial differences in coating performance.
SCOPE
1.1 This practice covers the preparation of zinc-coated and zinc-alloy-coated sheet steel panels to be used for testing paint, varnish, lacquer, conversion coatings, and related products. It covers sheet steel coated with hot dipped galvanized, one-side galvanized, electrogalvanized, zinc-iron alloy coatings (such as galvanneal), and zinc-5 % aluminum alloy coatings. It does not cover steel panels coated with 55 % aluminum-45 % zinc alloy, because these behave more like aluminum than zinc.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off