ASTM A480/A480M-18
(Specification)Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
Standard Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
ABSTRACT
This specification covers general requirements for flat-rolled stainless and heat-resisting steel plate, sheet, and strip. The steel shall be made by one of the following processes: electric-arc, electric-induction, or other suitable processes. Heat and product analyses shall conform to the chemical requirements for each of the specific elements. The material shall undergo mechanical tests such as tension test, hardness test, and bend test. Special tests like intergranular corrosion test, permeability test, Charpy impact testing and tests for detrimental intermetallic phases in wrought duplex stainless steels shall be also be performed when required.
SCOPE
1.1 This specification2 covers a group of general requirements that, unless otherwise specified in the purchase order or in an individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by ASTM: Specifications A240/A240M, A263, A264, A265, A666, A693, A793, and A895.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets, except that when A480M is specified, Annex A3 shall apply for the dimensional tolerances and not the bracketed SI values in Annex A2. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.4 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished in inch-pound units.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A480/A480M −18
Standard Specification for
General Requirements for Flat-Rolled Stainless and Heat-
1
Resisting Steel Plate, Sheet, and Strip
This standard is issued under the fixed designationA480/A480M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard-
2
1.1 This specification covers a group of general require-
ization established in the Decision on Principles for the
ments that, unless otherwise specified in the purchase order or
Development of International Standards, Guides and Recom-
in an individual specification, shall apply to rolled steel plate,
mendations issued by the World Trade Organization Technical
sheet, and strip, under each of the following specifications
Barriers to Trade (TBT) Committee.
issued by ASTM: Specifications A240/A240M, A263, A264,
A265, A666, A693, A793, and A895.
2. Referenced Documents
1.2 In the case of conflict between a requirement of a
3
2.1 ASTM Standards:
product specification and a requirement of this specification,
A240/A240M Specification for Chromium and Chromium-
the product specification shall prevail. In the case of conflict
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
between a requirement of the product specification or a
Vessels and for General Applications
requirement of this specification and a more stringent require-
A262 Practices for Detecting Susceptibility to Intergranular
ment of the purchase order, the purchase order shall prevail.
Attack in Austenitic Stainless Steels
The purchase order requirements shall not take precedence if
A263 Specification for Stainless Chromium Steel-Clad Plate
they, in any way, violate the requirements of the product
A264 Specification for Stainless Chromium-Nickel Steel-
specification or this specification; for example, by waiving a
Clad Plate
test requirement or by making a test requirement less stringent.
A265 Specification for Nickel and Nickel-Base Alloy-Clad
1.3 The values stated in either inch-pound units or SI units Steel Plate
A342/A342M Test Methods for Permeability of Weakly
are to be regarded separately as standard. Within the text, the
Magnetic Materials
SI units are shown in brackets, except that when A480M is
A370 Test Methods and Definitions for Mechanical Testing
specified, AnnexA3 shall apply for the dimensional tolerances
of Steel Products
andnotthebracketedSIvaluesinAnnexA2.Thevaluesstated
A666 Specification forAnnealed or Cold-WorkedAustenitic
in each system are not exact equivalents; therefore, each
Stainless Steel Sheet, Strip, Plate, and Flat Bar
system must be used independently of the other. Combining
A693 Specification for Precipitation-Hardening Stainless
values from the two systems may result in nonconformance
and Heat-Resisting Steel Plate, Sheet, and Strip
with the specification.
A700 Guide for Packaging, Marking, and Loading Methods
1.4 This specification and the applicable material specifica-
for Steel Products for Shipment
tions are expressed in both inch-pound and SI units. However,
A751 Test Methods, Practices, and Terminology for Chemi-
unless the order specifies the applicable “M” specification
cal Analysis of Steel Products
designation [SI units], the material shall be furnished in
A763 Practices for Detecting Susceptibility to Intergranular
inch-pound units.
Attack in Ferritic Stainless Steels
A793 Specification for Rolled Floor Plate, Stainless Steel
A895 SpecificationforFree-MachiningStainlessSteelPlate,
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Sheet, and Strip
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.17 on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Sept. 1, 2018. Published September 2018. Originally
3
approved in 1962. Last previous edition approved in 2017 as A480/A480M – 17. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
DOI: 10.1520/A0480_A0480M-18. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi- Standards volume information, refer to the standard’s Document Summary page on
cation SA – 480 in Section II of that Code. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
----------------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A480/A480M − 17 A480/A480M − 18
Standard Specification for
General Requirements for Flat-Rolled Stainless and Heat-
1
Resisting Steel Plate, Sheet, and Strip
This standard is issued under the fixed designation A480/A480M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers a group of general requirements that, unless otherwise specified in the purchase order or in an
individual specification, shall apply to rolled steel plate, sheet, and strip, under each of the following specifications issued by
ASTM: Specifications A240/A240M, A263, A264, A265, A666, A693, A793, and A895.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product
specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this
specification and a more stringent requirement of the purchase order, the purchase order shall prevail. The purchase order
requirements shall not take precedence if they, in any way, violate the requirements of the product specification or this
specification; for example, by waiving a test requirement or by making a test requirement less stringent.
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets, except that when A480M is specified, Annex A3 shall apply for the dimensional tolerances and not the
bracketed SI values in Annex A2. The values stated in each system are not exact equivalents; therefore, each system must be used
independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.4 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unless
the order specifies the applicable “M” specification designation [SI units], the material shall be furnished in inch-pound units.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A263 Specification for Stainless Chromium Steel-Clad Plate
A264 Specification for Stainless Chromium-Nickel Steel-Clad Plate
A265 Specification for Nickel and Nickel-Base Alloy-Clad Steel Plate
A342/A342M Test Methods for Permeability of Weakly Magnetic Materials
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A666 Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar
A693 Specification for Precipitation-Hardening Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
A700 Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Nov. 1, 2017Sept. 1, 2018. Published November 2017September 2018. Originally approved in 1962. Last previous edition approved in 20162017
as A480/A480MA480/A480M – 17. – 16b. DOI: 10.1520/A0480_A0480M-17.10.1520/A0480_A0480M-18.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA – 480 in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.