ASTM C1802-18a
(Specification)Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Horizontal Access Hatches for Utility, Water, and Wastewater Structures
Standard Specification for Design, Testing, Manufacture, Selection, and Installation of Fabricated Metal Horizontal Access Hatches for Utility, Water, and Wastewater Structures
SCOPE
1.1 This specification covers the design, testing, manufacture, selection, and installation of fabricated metal access hatches for utility, water, and wastewater structures including utility vaults, drainage structures, valve vaults, meter vaults, wet wells, pump enclosures, utility trenches, piping trenches, and drainage trenches.
1.2 This specification is applicable to various configurations of access hatches constructed of fabricated metal of various materials and grades for various loading conditions, traffic speeds, or both.
1.3 Engineering design and testing criteria are provided for access hatches to be located in various areas subjected to various loading conditions, traffic speed, frequency, or combinations thereof.
1.4 Proof loading criteria is provided to allow the access hatches to be designed by engineering calculation and/or by ultimate strength load testing.
1.5 Production loading criteria is provided to allow the access hatches to be tested to verify the load capacity of the manufactured hatches.
1.6 Hatch loading selection guidelines are included to allow selection of the proper hatch design loading for the conditions of the actual area of placement.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered the standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1802 −18a
Standard Specification for
Design, Testing, Manufacture, Selection, and Installation of
Fabricated Metal Horizontal Access Hatches for Utility,
1,2
Water, and Wastewater Structures
This standard is issued under the fixed designation C1802; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope conversions to SI units that are provided for information only
and are not considered the standard.
1.1 This specification covers the design, testing,
1.8 This standard does not purport to address all of the
manufacture, selection, and installation of fabricated metal
safety concerns, if any, associated with its use. It is the
access hatches for utility, water, and wastewater structures
responsibility of the user of this standard to establish appro-
includingutilityvaults,drainagestructures,valvevaults,meter
priate safety, health, and environmental practices and deter-
vaults, wet wells, pump enclosures, utility trenches, piping
mine the applicability of regulatory limitations prior to use.
trenches, and drainage trenches.
1.9 This international standard was developed in accor-
1.2 Thisspecificationisapplicabletovariousconfigurations
dance with internationally recognized principles on standard-
of access hatches constructed of fabricated metal of various
ization established in the Decision on Principles for the
materials and grades for various loading conditions, traffic
Development of International Standards, Guides and Recom-
speeds, or both.
mendations issued by the World Trade Organization Technical
1.3 Engineering design and testing criteria are provided for
Barriers to Trade (TBT) Committee.
access hatches to be located in various areas subjected to
2. Referenced Documents
various loading conditions, traffic speed, frequency, or combi-
3
nations thereof.
2.1 ASTM Standards:
A36/A36MSpecification for Carbon Structural Steel
1.4 Proof loading criteria is provided to allow the access
A53/A53MSpecification for Pipe, Steel, Black and Hot-
hatches to be designed by engineering calculation and/or by
Dipped, Zinc-Coated, Welded and Seamless
ultimate strength load testing.
A123/A123MSpecification for Zinc (Hot-Dip Galvanized)
1.5 Production loading criteria is provided to allow the
Coatings on Iron and Steel Products
access hatches to be tested to verify the load capacity of the
A176Specification for Stainless and Heat-Resisting Chro-
manufactured hatches. 4
mium Steel Plate, Sheet, and Strip (Withdrawn 2015)
A240/A240MSpecification for Chromium and Chromium-
1.6 Hatchloadingselectionguidelinesareincludedtoallow
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
selection of the proper hatch design loading for the conditions
Vessels and for General Applications
of the actual area of placement.
A242/A242MSpecification for High-Strength Low-Alloy
1.7 The values stated in inch-pound units are to be regarded
Structural Steel
as standard. The values given in parentheses are mathematical
A276Specification for Stainless Steel Bars and Shapes
A325Specification for Structural Bolts, Steel, Heat Treated,
120/105 ksi Minimum Tensile Strength (Withdrawn
1 4
ThisspecificationisunderthejurisdictionofASTMCommitteeC27onPrecast
2016)
Concrete Products and is the direct responsibility of Subcommittee C27.10 on
A490Specification for Structural Bolts, Alloy Steel, Heat
Utility Structures.
Treated, 150 ksi Minimum Tensile Strength (Withdrawn
Current edition approved May 15, 2018. Published June 2018. Originally
4
approved in 2014. Last previous edition approved in 2018 as C1802–18. DOI:
2016)
10.1520/C1802-18A.
2
This specification is primarily a design, testing, manufacturing, selection,
3
purchasing, and installation specification. The successful performance of this For referenced ASTM standards, visit the ASTM website, www.astm.org, or
product depends upon the proper selection of the loading criteria based on the contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
product’s actual use and the products proper installation. The purchaser of the Standards volume information, refer to the standard’s Document Summary page on
fabricated metal access hatches specified herein is cautioned that proper correlation the ASTM website.
4
of the loading conditions, proper installation for the hatch specified, and provision The last approved version of this historical standard is referenced on
for inspection of the installation at the construction site, are required. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
----------
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1802 − 18 C1802 − 18a
Standard Specification for
Design, Testing, Manufacture, Selection, and Installation of
Fabricated Metal Horizontal Access Hatches for Utility,
1,2
Water, and Wastewater Structures
This standard is issued under the fixed designation C1802; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the design, testing, manufacture, selection, and installation of fabricated metal access hatches for
utility, water, and wastewater structures including utility vaults, drainage structures, valve vaults, meter vaults, wet wells, pump
enclosures, utility trenches, piping trenches, and drainage trenches.
1.2 This specification is applicable to various configurations of access hatches constructed of fabricated metal of various
materials and grades for various loading conditions, traffic speeds, or both.
1.3 Engineering design and testing criteria are provided for access hatches to be located in various areas subjected to various
loading conditions, traffic speed, frequency, or combinations thereof.
1.4 Proof loading criteria is provided to allow the access hatches to be designed by engineering calculation and/or by ultimate
strength load testing.
1.5 Production loading criteria is provided to allow the access hatches to be tested to verify the load capacity of the
manufactured hatches.
1.6 Hatch loading selection guidelines are included to allow selection of the proper hatch design loading for the conditions of
the actual area of placement.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered the standard.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A123/A123M Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
4
A176 Specification for Stainless and Heat-Resisting Chromium Steel Plate, Sheet, and Strip (Withdrawn 2015)
1
This specification is under the jurisdiction of ASTM Committee C27 on Precast Concrete Products and is the direct responsibility of Subcommittee C27.10 on Utility
Structures.
Current edition approved April 1, 2018May 15, 2018. Published April 2018June 2018. Originally approved in 2014. Last previous edition approved in 20142018 as
ɛ1
C1802–14–18. . DOI: 10.1520/C1802-18.10.1520/C1802-18A.
2
This specification is primarily a design, testing, manufacturing, selection, purchasing, and installation specification. The successful performance of this product depends
upon the proper selection of the loading criteria based on the product’s actual use and the products proper installation. The purchaser of the fabricated metal access hatches
specified herein is cautioned that proper correlation of the loading conditions, proper installation for the hatch specified, and provision for inspection of the installation at
the construction site, are required.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1802 − 18a
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.