Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability

ABSTRACT
This specification covers the three types and four strength grades of high strength low-alloy, hot rolled structural steel plate with improved formability. These steels are normally furnished in the as-rolled condition. For plates produced from coil, and furnished without heat treatment or with stress relieving only, additional testing requirements and the reporting of additional test results, of a reference material shall apply. Chemical composition requirements shall be dependent upon thickness, grade, and intended applications. Tension tests shall be executed to evaluate conformance of specimens with specified mechanical properties requirements.
SCOPE
1.1 This specification covers three types and five strength grades of high-strength low-alloy, hot-rolled structural steel plate for use in truck frames, brackets, crane booms, rail cars, and similar applications. Steels that conform to this specification offer improved formability. These steels are normally furnished in the as-rolled condition. The type and strength grade furnished is as agreed upon between the manufacturer and the purchaser. The types and strength grades are shown in the tables.  
1.2 The maximum thickness of plates shall be as follows:    
Grade  
Plate Thickness, max,
in. [mm]  
50  
2 [50]  
60  
11/2 [40]  
70  
1 [25]  
80  
1 [25]  
100  
1/2 [13]  
1.3 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
30-Apr-2018
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM A656/A656M-18 - Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM A656/A656M-18 - Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
ASTM A656/A656M-18 - Standard Specification for Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate with Improved Formability
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:A656/A656M −18
Standard Specification for
Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate
1
with Improved Formability
This standard is issued under the fixed designationA656/A656M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers three types and five strength 2.1 ASTM Standards:
grades of high-strength low-alloy, hot-rolled structural steel A6/A6M Specification for General Requirements for Rolled
plate for use in truck frames, brackets, crane booms, rail cars, Structural Steel Bars, Plates, Shapes, and Sheet Piling
and similar applications. Steels that conform to this specifica-
3. General Requirements for Delivery
tion offer improved formability. These steels are normally
3.1 Plates furnished under this specification shall conform
furnished in the as-rolled condition. The type and strength
to the requirements of the current edition of Specification
grade furnished is as agreed upon between the manufacturer
A6/A6M, for the specific plate ordered, unless a conflict exists,
and the purchaser. The types and strength grades are shown in
in which case this specification shall prevail.
the tables.
3.2 Coils are excluded from qualification to this specifica-
1.2 The maximum thickness of plates shall be as follows:
tion until they are processed into finished plates. Plates
Grade Plate Thickness, max,
in. [mm] produced from coil means plates that have been cut to
individual lengths from a coil. The processor directly controls,
50 2 [50]
or is responsible for, the operations involved in the processing
1
60 1 ⁄2 [40]
70 1 [25] ofacoilintofinishedplates.Suchoperationsincludedecoiling,
80 1 [25]
leveling, cutting to length, testing, inspection, conditioning,
1
100 ⁄2 [13]
heat treatment (if applicable), packaging, marking, loading for
1.3 The values stated in either inch-pound units or SI units
shipment, and certification.
are to be regarded as standard. Within the text, the SI units are
NOTE 1—For plates produced from coil and furnished without heat
shown in brackets. The values stated in each system are not
treatment or with stress relieving only, two test results are to be reported
exact equivalents; therefore, each system must be used inde-
foreachqualifyingcoil.Additionalrequirementsregardingplateproduced
pendentlyoftheother.Combiningvaluesfromthetwosystems
from coil are described in Specification A6/A6M.
may result in nonconformance with this specification.
4. Materials and Manufacture
1.4 For plates produced from coil and furnished without
4.1 The steel shall be made to fine grain practice.
heat treatment or with stress relieving only, the additional
requirements,includingadditionaltestingrequirementsandthe
5. Chemical Composition
reporting of additional test results, of Specification A6/A6M
5.1 Heat analyses shall conform to the chemical require-
apply.
ments given in Table 1. Dependent upon thickness, grade, and
1.5 This international standard was developed in accor-
intended application, variations in the chemical composition
dance with internationally recognized principles on standard-
are permitted within the limits given in Table 1 for the
ization established in the Decision on Principles for the
applicable type. Where it is of particular importance, the
Development of International Standards, Guides and Recom-
manufacturer should be consulted for specific chemical com-
mendations issued by the World Trade Organization Technical
position.
Barriers to Trade (TBT) Committee.
5.2 Product Analysis—If a product analysis is made, it shall
conform to the requirements given in Table 1, subject to the
product analysis tolerances of Specification A6/A6M.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
2
A01.02 on Structural Steel for Bridges, Buildings, Rolling Stock and Ships. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2018. Published May 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1972. Last previous edition approved in 2013 as A656/A656M – 13. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0656_A0656M-18. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM Inter
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A656/A656M − 13 A656/A656M − 18
Standard Specification for
Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate
1
with Improved Formability
This standard is issued under the fixed designation A656/A656M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers three types and five strength grades of high-strength low-alloy, hot rolled hot-rolled structural steel
plate for use in truck frames, brackets, crane booms, rail cars, and similar applications. Steels that conform to this specification
offer improved formability. These steels are normally furnished in the as-rolled condition. The type and strength grade furnished
is as agreed upon between the manufacturer and the purchaser. The types and strength grades are shown in the tables.
1.2 The maximum thickness of plates shall be as follows:
Grade Plate Thickness, max,
in. [mm]
50 2 [50]
1
60 1 ⁄2 [40]
70 1 [25]
80 1 [25]
1
100 ⁄2 [13]
1.3 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown
in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the
other. Combining values from the two systems may result in nonconformance with this specification. See Appendix X3 of
Specification A6/A6M for information on weldability.
1.4 For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements,
including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
3. General Requirements for Delivery
3.1 Plates furnished under this specification shall conform to the requirements of the current edition of Specification A6/A6M,
for the specific plate ordered, unless a conflict exists, in which case this specification shall prevail.
3.2 Coils are excluded from qualification to this specification until they are processed into finished plates. Plates produced from
coil means plates that have been cut to individual lengths from a coil. The processor directly controls, or is responsible for, the
operations involved in the processing of a coil into finished plates. Such operations include decoiling, leveling, cutting to length,
testing, inspection, conditioning, heat treatment (if applicable), packaging, marking, loading for shipment, and certification.
NOTE 1—For plates produced from coil and furnished without heat treatment or with stress relieving only, two test results are to be reported for each
qualifying coil. Additional requirements regarding plate produced from coil are described in Specification A6/A6M.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.02
on Structural Steel for Bridges, Buildings, Rolling Stock and Ships.
Current edition approved Oct. 15, 2013May 1, 2018. Published November 2013May 2018. Originally approved in 1972. Last previous edition approved in 20122013 as
ε1
A656/A656M – 12aA656/A656M – 13. . DOI: 10.1520/A0656_A0656M-13.10.1520/A0656_A0656M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A656/A656M − 18
4. Materials and Manufacture
4.1 The steel shall be made to fine grain practice.
5. Chemical Composition
5.1 Heat analyses shall conform to the chemical re
...

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A656/A656M − 18
Standard Specification for
Hot-Rolled Structural Steel, High-Strength Low-Alloy Plate
1
with Improved Formability
This standard is issued under the fixed designation A656/A656M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
1.1 This specification covers three types and five strength 2.1 ASTM Standards:
grades of high-strength low-alloy, hot-rolled structural steel A6/A6M Specification for General Requirements for Rolled
plate for use in truck frames, brackets, crane booms, rail cars, Structural Steel Bars, Plates, Shapes, and Sheet Piling
and similar applications. Steels that conform to this specifica-
3. General Requirements for Delivery
tion offer improved formability. These steels are normally
3.1 Plates furnished under this specification shall conform
furnished in the as-rolled condition. The type and strength
to the requirements of the current edition of Specification
grade furnished is as agreed upon between the manufacturer
A6/A6M, for the specific plate ordered, unless a conflict exists,
and the purchaser. The types and strength grades are shown in
in which case this specification shall prevail.
the tables.
3.2 Coils are excluded from qualification to this specifica-
1.2 The maximum thickness of plates shall be as follows:
tion until they are processed into finished plates. Plates
Grade Plate Thickness, max,
in. [mm] produced from coil means plates that have been cut to
individual lengths from a coil. The processor directly controls,
50 2 [50]
or is responsible for, the operations involved in the processing
1
60 1 ⁄2 [40]
70 1 [25] of a coil into finished plates. Such operations include decoiling,
80 1 [25]
leveling, cutting to length, testing, inspection, conditioning,
1
100 ⁄2 [13]
heat treatment (if applicable), packaging, marking, loading for
1.3 The values stated in either inch-pound units or SI units
shipment, and certification.
are to be regarded as standard. Within the text, the SI units are
NOTE 1—For plates produced from coil and furnished without heat
shown in brackets. The values stated in each system are not
treatment or with stress relieving only, two test results are to be reported
exact equivalents; therefore, each system must be used inde-
for each qualifying coil. Additional requirements regarding plate produced
pendently of the other. Combining values from the two systems
from coil are described in Specification A6/A6M.
may result in nonconformance with this specification.
4. Materials and Manufacture
1.4 For plates produced from coil and furnished without
4.1 The steel shall be made to fine grain practice.
heat treatment or with stress relieving only, the additional
requirements, including additional testing requirements and the
5. Chemical Composition
reporting of additional test results, of Specification A6/A6M
5.1 Heat analyses shall conform to the chemical require-
apply.
ments given in Table 1. Dependent upon thickness, grade, and
1.5 This international standard was developed in accor-
intended application, variations in the chemical composition
dance with internationally recognized principles on standard-
are permitted within the limits given in Table 1 for the
ization established in the Decision on Principles for the
applicable type. Where it is of particular importance, the
Development of International Standards, Guides and Recom-
manufacturer should be consulted for specific chemical com-
mendations issued by the World Trade Organization Technical
position.
Barriers to Trade (TBT) Committee.
5.2 Product Analysis—If a product analysis is made, it shall
conform to the requirements given in Table 1, subject to the
product analysis tolerances of Specification A6/A6M.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
2
A01.02 on Structural Steel for Bridges, Buildings, Rolling Stock and Ships. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 1, 2018. Published May 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1972. Last previous edition approved in 2013 as A656/A656M – 13. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A0656_A0656M-18. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.