ASTM D2892-17
(Test Method)Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)
Standard Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)
SIGNIFICANCE AND USE
5.1 This test method is one of a number of tests conducted on a crude oil to determine its value. It provides an estimate of the yields of fractions of various boiling ranges and is therefore valuable in technical discussions of a commercial nature.
5.2 This test method corresponds to the standard laboratory distillation efficiency referred to as 15/5. The fractions produced can be analyzed as produced or combined to produce samples for analytical studies, engineering, and product quality evaluations. The preparation and evaluation of such blends is not part of this test method.
5.3 This test method can be used as an analytical tool for examination of other petroleum mixtures with the exception of LPG, very light naphthas, and mixtures with initial boiling points above 400 °C.
SCOPE
1.1 This test method covers the procedure for the distillation of stabilized crude petroleum (see Note 1) to a final cut temperature of 400 °C Atmospheric Equivalent Temperature (AET). This test method employs a fractionating column having an efficiency of 14 to 18 theoretical plates operated at a reflux ratio of 5:1. Performance criteria for the necessary equipment is specified. Some typical examples of acceptable apparatus are presented in schematic form. This test method offers a compromise between efficiency and time in order to facilitate the comparison of distillation data between laboratories.
Note 1: Defined as having a Reid vapor pressure less than 82.7 kPa (12 psi).
1.2 This test method details procedures for the production of a liquefied gas, distillate fractions, and residuum of standardized quality on which analytical data can be obtained, and the determination of yields of the above fractions by both mass and volume. From the preceding information, a graph of temperature versus mass % distilled can be produced. This distillation curve corresponds to a laboratory technique, which is defined at 15/5 (15 theoretical plate column, 5:1 reflux ratio) or TBP (true boiling point).
1.3 This test method can also be applied to any petroleum mixture except liquefied petroleum gases, very light naphthas, and fractions having initial boiling points above 400 °C.
1.4 This test method contains the following annexes and appendixes:
1.4.1 Annex A1—Test Method for the Determination of the Efficiency of a Distillation Column,
1.4.2 Annex A2—Test Method for the Determination of the Dynamic Holdup of a Distillation Column,
1.4.3 Annex A3—Test Method for the Determination of the Heat Loss in a Distillation Column (Static Conditions),
1.4.4 Annex A4—Test Method for the Verification of Temperature Sensor Location,
1.4.5 Annex A5—Test Method for Determination of the Temperature Response Time,
1.4.6 Annex A6—Practice for the Calibration of Sensors,
1.4.7 Annex A7—Test Method for the Verification of Reflux Dividing Valves,
1.4.8 Annex A8—Practice for Conversion of Observed Vapor Temperature to Atmospheric Equivalent Temperature (AET),
1.4.9 Appendix X1—Test Method for Dehydration of a Sample of Wet Crude Oil, and
1.4.10 Appendix X2—Practice for Performance Check.
1.5 The values stated in SI units are to be regarded as the standard.
1.5.1 Exception—The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 10.
1.7 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product ...
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D2892 − 17
Standard Test Method for
Distillation of Crude Petroleum (15-Theoretical Plate
1
Column)
This standard is issued under the fixed designation D2892; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.4.4 Annex A4—Test Method for the Verification of Tem-
perature Sensor Location,
1.1 Thistestmethodcoverstheprocedureforthedistillation
1.4.5 Annex A5—Test Method for Determination of the
of stabilized crude petroleum (see Note 1) to a final cut
Temperature Response Time,
temperature of 400°C Atmospheric Equivalent Temperature
1.4.6 Annex A6—Practice for the Calibration of Sensors,
(AET). This test method employs a fractionating column
1.4.7 Annex A7—Test Method for the Verification of Reflux
havinganefficiencyof 14 to 18 theoretical plates operatedata
Dividing Valves,
reflux ratio of 5:1. Performance criteria for the necessary
1.4.8 Annex A8—Practice for Conversion of Observed Va-
equipment is specified. Some typical examples of acceptable
por Temperature to Atmospheric Equivalent Temperature
apparatus are presented in schematic form. This test method
(AET),
offers a compromise between efficiency and time in order to
1.4.9 Appendix X1—Test Method for Dehydration of a
facilitate the comparison of distillation data between laborato-
Sample of Wet Crude Oil, and
ries.
1.4.10 Appendix X2—Practice for Performance Check.
NOTE 1—Defined as having a Reid vapor pressure less than 82.7kPa
(12psi).
1.5 The values stated in SI units are to be regarded as the
standard.
1.2 Thistestmethoddetailsproceduresfortheproductionof
1.5.1 Exception—The values given in parentheses are for
a liquefied gas, distillate fractions, and residuum of standard-
information only.
ized quality on which analytical data can be obtained, and the
determinationofyieldsoftheabovefractionsbybothmassand
1.6 This standard does not purport to address all of the
volume. From the preceding information, a graph of tempera-
safety concerns, if any, associated with its use. It is the
ture versus mass % distilled can be produced. This distillation
responsibility of the user of this standard to establish appro-
curve corresponds to a laboratory technique, which is defined priate safety and health practices and determine the applica-
at 15/5 (15 theoretical plate column, 5:1 reflux ratio) or TBP
bility of regulatory limitations prior to use. For specific
(true boiling point). warning statements, see Section 10.
1.7 WARNING—Mercury has been designated by many
1.3 This test method can also be applied to any petroleum
regulatory agencies as a hazardous material that can cause
mixture except liquefied petroleum gases, very light naphthas,
central nervous system, kidney, and liver damage. Mercury, or
and fractions having initial boiling points above 400°C.
its vapor, may be hazardous to health and corrosive to
1.4 This test method contains the following annexes and
materials.Cautionshouldbetakenwhenhandlingmercuryand
appendixes:
mercury containing products. See the applicable product Ma-
1.4.1 Annex A1—Test Method for the Determination of the
terial Safety Data Sheet (MSDS) for details and EPA’s
Efficiency of a Distillation Column,
website—http://www.epa.gov/mercury/faq.htm—for addi-
1.4.2 Annex A2—Test Method for the Determination of the
tional information. Users should be aware that selling mercury
Dynamic Holdup of a Distillation Column, and/or mercury containing products into your state or country
1.4.3 Annex A3—Test Method for the Determination of the may be prohibited by law.
Heat Loss in a Distillation Column (Static Conditions),
1.8 This international standard was developed in accor-
dance with internationally recognized principles on standard-
ization established in the Decision on Principles for the
1
Development of International Standards, Guides and Recom-
This test method is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
mendations issued by the World Trade Organization Technical
Subcommittee D02.08 on Volatility.
Barriers to Trade (TBT) Committee.
Current edition approved May 1, 2017. Published May 2017. Originally
approved in 1970. Last previous edition approved in 2016 as D2892–16. DOI:
10.1520/D2892-17.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D2892 − 17
2. Referenced Documents 3.1.2 boilup rate, n—in distillation, the quantity of vapor
2 enteri
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2892 − 16 D2892 − 17
Standard Test Method for
Distillation of Crude Petroleum (15-Theoretical Plate
1
Column)
This standard is issued under the fixed designation D2892; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This test method covers the procedure for the distillation of stabilized crude petroleum (see Note 1) to a final cut temperature
of 400 °C Atmospheric Equivalent Temperature (AET). This test method employs a fractionating column having an efficiency of
14 to 18 theoretical plates operated at a reflux ratio of 5:1. Performance criteria for the necessary equipment is specified. Some
typical examples of acceptable apparatus are presented in schematic form. This test method offers a compromise between efficiency
and time in order to facilitate the comparison of distillation data between laboratories.
NOTE 1—Defined as having a Reid vapor pressure less than 82.7 kPa (12 psi).
1.2 This test method details procedures for the production of a liquefied gas, distillate fractions, and residuum of standardized
quality on which analytical data can be obtained, and the determination of yields of the above fractions by both mass and volume.
From the preceding information, a graph of temperature versus mass % distilled can be produced. This distillation curve
corresponds to a laboratory technique, which is defined at 15/5 (15 theoretical plate column, 5:1 reflux ratio) or TBP (true boiling
point).
1.3 This test method can also be applied to any petroleum mixture except liquefied petroleum gases, very light naphthas, and
fractions having initial boiling points above 400 °C.
1.4 This test method contains the following annexes and appendixes:
1.4.1 Annex A1—Test Method for the Determination of the Efficiency of a Distillation Column,
1.4.2 Annex A2—Test Method for the Determination of the Dynamic Holdup of a Distillation Column,
1.4.3 Annex A3—Test Method for the Determination of the Heat Loss in a Distillation Column (Static Conditions),
1.4.4 Annex A4—Test Method for the Verification of Temperature Sensor Location,
1.4.5 Annex A5—Test Method for Determination of the Temperature Response Time,
1.4.6 Annex A6—Practice for the Calibration of Sensors,
1.4.7 Annex A7—Test Method for the Verification of Reflux Dividing Valves,
1.4.8 Annex A8—Practice for Conversion of Observed Vapor Temperature to Atmospheric Equivalent Temperature (AET),
1.4.9 Appendix X1—Test Method for Dehydration of a Sample of Wet Crude Oil, and
1.4.10 Appendix X2—Practice for Performance Check.
1.5 The values stated in SI units are to be regarded as the standard.
1.5.1 Exception—The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For specific warning statements, see Section 10.
1.7 WARNING—Mercury has been designated by many regulatory agencies as a hazardous material that can cause central
nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution
should be taken when handling mercury and mercury containing products. See the applicable product Material Safety Data Sheet
(MSDS) for details and EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware
that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.08 on Volatility.
Current edition approved Dec. 1, 2016May 1, 2017. Published January 2017May 2017. Originally approved in 1970. Last previous edition approved in 20152016 as
D2892 – 15.D2892 – 16. DOI: 10.1520/D2892-16.10.1520/D2892-17.
*A Summary of Changes section appears at the end of
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.