ASTM D6963-04e1
(Terminology)Standard Terminology Relating to Sewn Products Automation (Withdrawn 2013)
Standard Terminology Relating to Sewn Products Automation (Withdrawn 2013)
SCOPE
1.1 This standard is compilation of all terminology which is related and specific to Sewn Products Automation.
1.2 Diagrams and illustration included in this compilation are intended to provide a better understanding of the concepts defined.
WITHDRAWN RATIONALE
This standard is compilation of all terminology which is related and specific to Sewn Products Automation.
Formerly under the jurisdiction of Committee D13 on Textiles, this terminology was withdrawn in January 2013 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation: D6963 − 04
StandardTerminology Relating to
1
Sewn Products Automation
This standard is issued under the fixed designation D6963; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Terminology was added in July 2008.
1. Scope command, n—a two letter sequence, always written in capital
letters, that governs interpretation of formatted data. Also
1.1 This standard is compilation of all terminology which is
known as a syntax command.
related and specific to Sewn Products Automation.
curve interpolation point, n—those intermediate points gen-
1.2 Diagrams and illustration included in this compilation
erated between curve points by means of a CAD vendor’s
are intended to provide a better understanding of the concepts
system curve interpolation algorithm; those points used to
defined.
create a curve in order to represent a contour.
2. Referenced Documents
curve point, n—a user defined point on a contour.
2
DISCUSSION—When a curve interpolation algorithm is used to gener-
2.1 ASTM Standards:
ate a curve, the resulting curve must pass through all user defined curve
D6673 Practice for Sewn Products Pattern Data
points. (See curve interpolation points, validation curve.)
Interchange—Data Format
D6674 Guide for Proficiency Test Program for Fabrics curve tolerance, n—the maximum perpendicular distance that
the resulting curve can deviate from the original curve after
3. Terminology
transferring the data for the first time.
DISCUSSION—Sufficient points should be added by the originating
alternate grade reference line, n— an optional internal line
system to keep the shape of the curve within the user defined curve
whose orientation is used for the “ x” axis of a grade rule.
tolerance.
DISCUSSION—The application of a grade rule will be oriented to the
gradereferencelineunlessanalternategradereferencelineisspecified. cut file, n—numerically controlled fabric cutter instructions
(See grade reference line.)
entered in blocks of ASCII characters.
annotation text, n—optional user text that can be specifically cut lines, n—the outside edges of a pattern piece used as a
defined and displayed when the pattern piece is plotted. guide for cutting out the pattern piece. (See piece bound-
DISCUSSION—Annotation text is usually placed in specific locations
ary.)
within the piece boundary to identify important information such as the
data block, n—an organized group of commands and param-
drill hole diameter.
eters preceded by a header and followed by a terminator.
base size, n—the digitized or created size of a style. (See
drill hole, n—a point that is part of a pattern piece that is not
sample size.)
part of any line.
block, n—for cutting standard def., a sequence of commands
DISCUSSION—Drill holes may be used to denote pocket or buttonhole
within a cut file and which activate a response by the placement.
automated fabric cutter.
format classification interrogation, n—interactive direct on-
DISCUSSION—Ablock keyword should be used to identify the start of
line communication between systems which generates cut
information for a pattern piece and an end block keyword is used to
file interchange and fabric cutting equipment.
stop the data exchange.
function codes, n—codes used to control fabric cutter instruc-
tions and govern interpretation of subsequent commands and
1
ThisterminologyisunderthejurisdictionofASTMCommitteeD13onTextiles
data in a block.
and is the direct responsibility of Subcommittee D13.66 on Sewn Product
Automation.
grading,n—a method of creating multiple sizes from a base or
Current edition approved July 1, 2004. Published August 2004. DOI: 10.1520/
sample size using a grade rule.
D6963-04E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
graded nest, n—a collection of graded piece boundaries that
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
represent every size in the size line for a particular pattern
Standardsvolume information, refer to the standards’s Document Summary page on
the ASTM website. piece.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D6963 − 04
DISCUSSION—The CAD vendor’s system will apply the grade rules DISCUSSION—Notches are often used to line up two pieces of material
from the grade rule table to the base size of a piece to create the graded to be sewn together.
nest.
parameters, n—values that modify the action of a command.
grade reference line, n—the horizontal line that defines the x
piece boun
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.