ASTM C1527/C1527M-11(2018)
(Specification)Standard Specification for Travertine Dimension Stone
Standard Specification for Travertine Dimension Stone
ABSTRACT
This specification covers the material characteristics, physical requirements, and sampling method appropriate to the selection of travertine dimension stone for general building and structural purposes. Dimension travertine shall include stone that is sawed, cut, split, or otherwise finished or shaped, and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone. The physical property requirements to which travertine stones shall adhere to are absorption by weight, density, compressive strength, modulus of rupture, abrasion resistance, and flexural strength.
SCOPE
1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of travertine for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of travertine dimension stone.
1.2 Dimension travertine shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C1527/C1527M −11 (Reapproved 2018)
Standard Specification for
Travertine Dimension Stone
This standard is issued under the fixed designation C1527/C1527M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Subjected to Foot Traffic
C880/C880M Test Method for Flexural Strength of Dimen-
1.1 This specification covers the material characteristics,
sion Stone
physical requirements, and sampling appropriate to the selec-
C1242 Guide for Selection, Design, and Installation of
tion of travertine for general building and structural purposes.
Dimension Stone Attachment Systems
Refer to Guides C1242 and C1528 for the appropriate selection
C1353 Test Method for Abrasion Resistance of Dimension
and use of travertine dimension stone.
Stone Subjected to Foot Traffic Using a Rotary Platform
1.2 Dimension travertine shall include stone that is sawed,
Abraser
cut, split, or otherwise finished or shaped and shall specifically
C1528 Guide for Selection of Dimension Stone
exclude molded, cast, or otherwise artificially aggregated units
composed of fragments, and also crushed and broken stone.
3. Terminology
1.3 The values stated in either SI units or inch-pound units
3.1 All definitions are in accordance with Terminology
are to be regarded separately as standard. The values stated in
C119.
each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining 3.2 Definitions:
values from the two systems may result in non-conformance
3.2.1 fleuri-cut (cross-cut), adj—describes stone that is cut
with the standard.
parallel to the natural veining.
1.4 This international standard was developed in accor-
3.2.2 vein-cut, adj—describes stone that is cut perpendicular
dance with internationally recognized principles on standard-
to the natural veining.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4. Physical Properties
mendations issued by the World Trade Organization Technical
4.1 Travertine supplied under this specification shall con-
Barriers to Trade (TBT) Committee.
form to the physical requirements prescribed in Table 1.
2. Referenced Documents
4.2 Travertine shall be free of minerals that may cause
2.1 ASTM Standards:
objectionable staining under normal environments of use.
C97/C97M Test Methods for Absorption and Bulk Specific
4.3 Voids in travertine are a natural characteristic of the
Gravity of Dimension Stone
material and shall be considered in assessing the permissible
C99/C99M Test Method for Modulus of Rupture of Dimen-
natural variations suitable for a particular application.
sion Stone
C119 Terminology Relating to Dimension Stone 4.3.1 Some travertines may not be suitable for exterior use
C170/C170M Test Method for Compressive Strength of
in areas subject to frequent freeze-thaw cycles.
Dimension Stone
4.3.2 Travertine that is fleuri-cut (cross-cut) rather than
C241/C241M Test Method forAbrasion Resistance of Stone
vein-cut can be expected to experience certain problems,
because some areas of the exposed surface will consist of only
a thin layer of stone that covers a void in the stone.
This specification is under the jurisdiction of ASTM Committee C18 on
Dimension Stone and is the direct responsibility of Subcommittee C18.03 on
4.4 The desired color and texture, with their permissible
Material Specifications.
natural variations in material characteristics for material to be
Current edition approved Jan. 1, 2018. Published January 2018. Originally
produced for the project, shall be established by control
approved in 2002. Last pre
...
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1527/C1527M − 11 (Reapproved 2018)
Standard Specification for
Travertine Dimension Stone
This standard is issued under the fixed designation C1527/C1527M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Subjected to Foot Traffic
C880/C880M Test Method for Flexural Strength of Dimen-
1.1 This specification covers the material characteristics,
sion Stone
physical requirements, and sampling appropriate to the selec-
C1242 Guide for Selection, Design, and Installation of
tion of travertine for general building and structural purposes.
Dimension Stone Attachment Systems
Refer to Guides C1242 and C1528 for the appropriate selection
C1353 Test Method for Abrasion Resistance of Dimension
and use of travertine dimension stone.
Stone Subjected to Foot Traffic Using a Rotary Platform
1.2 Dimension travertine shall include stone that is sawed,
Abraser
cut, split, or otherwise finished or shaped and shall specifically
C1528 Guide for Selection of Dimension Stone
exclude molded, cast, or otherwise artificially aggregated units
composed of fragments, and also crushed and broken stone.
3. Terminology
1.3 The values stated in either SI units or inch-pound units
3.1 All definitions are in accordance with Terminology
are to be regarded separately as standard. The values stated in
C119.
each system may not be exact equivalents; therefore, each
system shall be used independently of the other. Combining 3.2 Definitions:
values from the two systems may result in non-conformance
3.2.1 fleuri-cut (cross-cut), adj—describes stone that is cut
with the standard.
parallel to the natural veining.
1.4 This international standard was developed in accor-
3.2.2 vein-cut, adj—describes stone that is cut perpendicular
dance with internationally recognized principles on standard-
to the natural veining.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
4. Physical Properties
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee. 4.1 Travertine supplied under this specification shall con-
form to the physical requirements prescribed in Table 1.
2. Referenced Documents
4.2 Travertine shall be free of minerals that may cause
2.1 ASTM Standards:
objectionable staining under normal environments of use.
C97/C97M Test Methods for Absorption and Bulk Specific
4.3 Voids in travertine are a natural characteristic of the
Gravity of Dimension Stone
material and shall be considered in assessing the permissible
C99/C99M Test Method for Modulus of Rupture of Dimen-
natural variations suitable for a particular application.
sion Stone
C119 Terminology Relating to Dimension Stone
4.3.1 Some travertines may not be suitable for exterior use
C170/C170M Test Method for Compressive Strength of in areas subject to frequent freeze-thaw cycles.
Dimension Stone
4.3.2 Travertine that is fleuri-cut (cross-cut) rather than
C241/C241M Test Method for Abrasion Resistance of Stone
vein-cut can be expected to experience certain problems,
because some areas of the exposed surface will consist of only
a thin layer of stone that covers a void in the stone.
This specification is under the jurisdiction of ASTM Committee C18 on
Dimension Stone and is the direct responsibility of Subcommittee C18.03 on
4.4 The desired color and texture, with their permissible
Material Specifications.
natural variations in material characteristics for material to be
Current edition approved Jan. 1, 2018. Published January 2018. Originally
produced for the project, shall be established by control
approved in 2002. Last previous edition approved in 2011 as C1527/C1527M- 11.
DOI: 10.1520/C1527-11R18.
samples. Representative
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1527/C1527M − 11 C1527/C1527M − 11 (Reapproved 2018)
Standard Specification for
Travertine Dimension Stone
This standard is issued under the fixed designation C1527/C1527M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the material characteristics, physical requirements, and sampling appropriate to the selection of
travertine for general building and structural purposes. Refer to Guides C1242 and C1528 for the appropriate selection and use of
travertine dimension stone.
1.2 Dimension travertine shall include stone that is sawed, cut, split, or otherwise finished or shaped and shall specifically
exclude molded, cast, or otherwise artificially aggregated units composed of fragments, and also crushed and broken stone.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
C97/C97M Test Methods for Absorption and Bulk Specific Gravity of Dimension Stone
C99/C99M Test Method for Modulus of Rupture of Dimension Stone
C119 Terminology Relating to Dimension Stone
C170/C170M Test Method for Compressive Strength of Dimension Stone
C241/C241M Test Method for Abrasion Resistance of Stone Subjected to Foot Traffic
C880/C880M Test Method for Flexural Strength of Dimension Stone
C1242 Guide for Selection, Design, and Installation of Dimension Stone Attachment Systems
C1353 Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform Abraser
C1528 Guide for Selection of Dimension Stone
3. Terminology
3.1 All definitions are in accordance with Terminology C119.
3.2 Definitions:
3.2.1 fleuri-cut (cross-cut), adj—describes stone that is cut parallel to the natural veining.
3.2.2 vein-cut, adj—describes stone that is cut perpendicular to the natural veining.
4. Physical Properties
4.1 Travertine supplied under this specification shall conform to the physical requirements prescribed in Table 1.
4.2 Travertine shall be free of minerals that may cause objectionable staining under normal environments of use.
4.3 Voids in travertine are a natural characteristic of the material and shall be considered in assessing the permissible natural
variations suitable for a particular application.
This specification is under the jurisdiction of ASTM Committee C18 on Dimension Stone and is the direct responsibility of Subcommittee C18.03 on Material
Specifications.
Current edition approved Jan. 1, 2011Jan. 1, 2018. Published January 2011January 2018. Originally approved in 2002. Last previous edition approved in 20102011 as
C1527/C1527M- 10.11. DOI: 10.1520/C1527-11.10.1520/C1527-11R18.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.