ASTM F2163-01

Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring

SCOPE
1.1 This specification covers inner rings for needle roller bearings with drawn outer rings.
1.2 The inner rings specified in this specification are intended for use on unhardened shafts in conjunction with open end needle roller bearings shown on Specification F 2162 and MS52141.
1.3 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged.
1.4 The inner rings specified in this specification are not intended for use in flight-critical systems of aircraft.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
Note 1—This specification was originally developed by the Department of Defense and maintained by the Defense Supply Center Richmond. It is intended to replicate the requirements of MS 17130.

General Information

• Status: Historical
• Publication Date: 09-Dec-2001
• Technical Committee: F34 - Rolling Element Bearings
• Drafting Committee: F34.04 - Automotive/Industrial Bearing

Relations

• Replaced By: ASTM F2163-01e1 - Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring
• Effective Date: 10-Dec-2001
• Referred By: ASTM F2431-04(2018) - Standard Specification for Ring Bearing, Inner: For Needle Roller Bearing with Thick Outer Ring
• Effective Date: 10-Dec-2001
• Referred By: ASTM F2162-01(2016) - Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type
• Effective Date: 10-Dec-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: F 2163 – 01
Standard Specification for
Ring, Bearing, Inner: for Needle Roller Bearing With Drawn
1
Outer Ring
This standard is issued under the fixed designation F 2163; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope MIL-STD-130 Identification Marking of US Military Prop-
6
erty
1.1 This specification covers inner rings for needle roller
MS52141 Bearing, Roller, Needle: Drawn Outer Ring,
bearings with drawn outer rings.
Caged, Without Inner Ring, Open and Closed End, Stan-
1.2 The inner rings specified in this specification are in-
6
dard Type
tended for use on unhardened shafts in conjunction with open
2.5 American Bearing Manufacturer’s Association (ABMA)
end needle roller bearings shown on Specification F 2162 and
Standard:
MS52141.
STD 4 Tolerance Definitions and Gauging Practices For
1.3 The use of recycled materials that meet the requirements
7
Ball and Roller Bearings
of the applicable material specification without jeopardizing
2.6 ISO Standard:
the intended use of the item is encouraged.
8
ISO 5593 Rolling Bearings—Vocabulary
1.4 The inner rings specified in this specification are not
intended for use in flight-critical systems of aircraft.
3. Terminology
1.5 The values stated in inch-pound units are to be regarded
3.1 Definitions—For definitions of terms used in this speci-
as the standard. The values given in parentheses are provided
fication, refer to ABMA STD 4 and ISO 5593.
for information only.
4. Ordering Information
NOTE 1—This specification was originally developed by the Depart-
ment of Defense and maintained by the Defense Supply Center Richmond.
4.1 When ordering parts in accordance with this specifica-
It is intended to replicate the requirements of MS 17130.
tion, specify the following:
4.1.1 ASTM designation number, including year of issue;
2. Referenced Documents
4.1.2 Dash number (see Table 1); and
2.1 ASTM Standards:
4.1.3 Dimensions of inner rings, including:
E 18 Test Methods for Rockwell Hardness and Rockwell
4.1.3.1 Bore diameter, in.;
2
Superficial Hardness of Metallic Materials
4.1.3.2 Outside diameter, in.;
F 2162 Specification for Bearing, Roller, Needle: Drawn
4.1.3.3 Width, in.; and
Outer Ring, Full Complement, Without Inner Ring, Open
4.1.3.4 Radius, in.
3
and Closed End, Standard Type
2.2 ASME Standard:
5. Materials and Manufacture
ASME B 46.1 Surface Texture Surface Roughness, Wavi-
5.1 Bearing inner rings shall be manufactured of steel, alloy
4
ness, and Lay
or carbon, carburizing grade 4620, 4720, 8620, 8720, or 1018,
2.3 SAE Standards:
1022, or 1117 in accordance with SAE AHS STD-66 or SAE
5
SAE AHS STD-66
E52100 in accordance with SAE J-404.
5
SAE J-404 Chemical Composition of SAE Alloy Steels
2.4 Military Standards:
6. Other Requirements
6.1 Heat Treatment:
6.1.1 Steel 4620, 4720, 8620, 8720, 1018, 1022, and 1117
1
This specification is under the jurisdiction of ASTM Committee F34 on Rolling
shall be case hardened to Rockwell HRC58-65, in accordance
Element Bearings and is the direct responsibility of Subcommittee F34.01 on
with Test Methods E 18. Case depth shall be 0.020 minimum.
Rolling Element.
Current edition approved Dec. 10, 2001. Published March 2002.
2
Annual Book of ASTM Standards, Vol 03.01.
3 6
Annual Book of ASTM Standards, Vol 01.08. Available from USA Information Systems, 1092 Laskin Rd., Ste. 208, Virginia
4
Available from Global Engineering Documents, 15 Inverness Way, East Beach, VA 23451.
7
Englewood, CO 8011. Available from the American Bearing Manufacturer’s Association, 1200 19th
5
Available from SAE International, 400 Commonwealth Dr., Warrendale, PA St. NW, Ste. 300, Washington, DC 20036–2401.
8
15096–0001. Available from ANSI, 1819 L St. NW, Ste. 600, Washington, DC 20036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 2163
TABLE 1 Inner Ring Dimensions
d F B Mating
Bore Diameter, in. Outside Diameter, in. Width, in. Bearings
Dash r
F 2162
Number Radius, in.
Dash
Nominal Minimum Maximum Nominal Minimum Maximum Minimum Maximum
A
Numbers
3 9
–61 ⁄8 0.3745 0.3750 ⁄16 0.5620 0.5625 0.505 0.515 0.025 –16
3 9
–62 ⁄8 0.3745 0.3750 ⁄16 0.5620 0.5625 0.755 0.765 0.025 –17
3 5
–63 ⁄8 0.3745 0.3750 ⁄8 0.6245 0.6250 0.505 0.515 0.025 –18
3 5
–1 ⁄8 0.3745 0.3750 ⁄8 0.6245 0.6250 0.755 0.765 0.025 –19
7 5
–64 ⁄16 0.4370 0.4375 ⁄8 0.6245 0.6250 0.776 0.789 0.025 –19
1 3
–65 ⁄2 0.4995 0.5000 ⁄4 0.7495 0.7500 0.505 0.515 0.040 –22
1 3
–2 ⁄2 0.4995 0.5000 ⁄4 0.7495 0.7500 0.755 0.765 0.040 –23
5 7
–4 ⁄8 0.624
...