iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D4756-02

(Practice)

Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit

Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit

SCOPE
1.1 This practice covers the minimum requirements for and the methods of installation of rigid vinyl siding, soffits, and accessories on the exterior wall and soffit areas of buildings. In all applications, refer also to the specific manufacturer's instructions for installation.
1.2 This practice covers aspects of installation relating to effectiveness and durability in service.
1.3 The various application systems are located in the following sections of this practice: Section 8 Substrate, Surface PreparationSection 9Application of Horizontal SidingSection 10Application of Vertical Siding Section 11Application of Soffits Section 12Special Details
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
Note 1—There are no ISO standards covering the subject matter of this practice.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Apr-2002
ICS
91.200 - Construction technology
Technical Committee
D20 - Plastics
Drafting Committee
D20.24 - Plastic Building Products
Current Stage
Ref Project

Relations

Replaces
ASTM D4756-96 - Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
Effective Date
10-Apr-2002
Replaced By
ASTM D4756-02a - Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
Effective Date
10-Nov-2002
Referred By
ASTM D7793-21 - Standard Specification for Insulated Vinyl Siding
Effective Date
10-Apr-2002
Referred By
ASTM D4477-22 - Standard Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) Soffit
Effective Date
10-Apr-2002
Referred By
ASTM D7445-18 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed Vinyl Siding)
Effective Date
10-Apr-2002
Referred By
ASTM E2266-22 - Standard Guide for Design and Construction of Low-Rise Frame Building Wall Systems to Resist Water Intrusion
Effective Date
10-Apr-2002
Referred By
ASTM D3679-21 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding
Effective Date
10-Apr-2002
Referred By
ASTM D5206-19 - Standard Test Method for Windload Resistance of Rigid Plastic Siding
Effective Date
10-Apr-2002

Buy Standard

ASTM D4756-02 - Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and SoffitASTM D4756-02 - Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
PreviousNext
Standard
ASTM D4756-02 - Standard Practice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and Soffit
English language
10 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard
Designation: D 4756 – 02
Standard Practice for
Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and
1
Soffit
This standard is issued under the fixed designation D 4756; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
4
1. Scope E 631 Terminology of Building Constructions
2.2 Council of American Building Offıcials:
1.1 This practice covers the minimum requirements for and
CABO One and Two Family Dwelling Code: Section
the methods of installation of rigid vinyl siding, soffits, and
5
R-707 Attic Ventilation
accessories on the exterior wall and soffit areas of buildings. In
all applications, refer also to the specific manufacturer’s
3. Terminology
instructions for installation.
3.1 General—Definitions are in accordance with Termi-
1.2 This practice covers aspects of installation relating to
nologies D 883 and E 631 and abbreviations with Terminology
effectiveness and durability in service.
D 1600 unless otherwise indicated.
1.3 The various application systems are located in the
3.2 Definitions of Terms Specific to This Standard:
following sections of this practice:
1
3.2.1 crimp—small protrusions, typically approximately ⁄2
Section 8 Substrate, Surface Preparation
1 1
in. (12.7 mm) long, ⁄8in. (3.2 mm) wide, and projecting ⁄8in.
Section 9 Application of Horizontal Siding
Section 10 Application of Vertical Siding
(3.2 mm) formed by a crimper (snaplock punch). (See Fig. 1.)
Section 11 Application of Soffits
3.2.2 crimper—a special hand tool designed to form crimps
Section 12 Special Details
(snaplock ears) intended to hold partial panels in place. (See
1.4 The values stated in inch-pound units are to be regarded
Fig. 1.)
as the standard. The SI units given in parentheses are for
3.2.3 fascia—the trim along the perimeter of roofs or roof
information only.
overhangs. (See Fig. 2.)
3.2.4 flashing—special membrane pieces or manufactured
NOTE 1—There are no ISO standards covering the subject matter of this
trim pieces used to supplement siding panels in weather
practice.
protection around openings, such as windows and doors.
1.5 This standard does not purport to address all of the
3.2.5 nailslot punch—a special hand tool used to create
safety concerns, if any, associated with its use. It is the
slots for attachment of field-modified siding or accessories.
responsibility of the user of this standard to establish appro-
(See Fig. 3.)
priate safety and health practices and determine the applica-
3.2.6 snaplock ears—See crimp and Fig. 1.
bility of regulatory limitations prior to use.
3.2.7 snaplock punch—See crimper and Fig. 1.
2. Referenced Documents 3.2.8 soffıt—the underside surface (typically horizontal) of
roof overhangs.
2.1 ASTM Standards:
2 3.2.9 Strapping—Flexible materials (i.e. metal strips or
D 883 Terminology Relating to Plastics
hurricane ties used to provide shear or wind resistance.
D 1600 Terminology for Abbreviated Terms Relating to
2 3.2.10 zip tool—a special hand tool used to separate inter-
Plastics
locked siding panels. (See Fig. 4.)
D 3679 Specification for Rigid Poly(Vinyl Chloride) (PVC)
3
Siding
4. Delivery of Materials
D 4477 Specification for Rigid Poly(Vinyl Chloride) (PVC)
3 4.1 All manufactured materials shall be delivered in the
Soffit
original packages, containers, or bundles bearing the size or
type product, or both, brand name, and manufacturer (or
supplier) identification, manufacturer’s lot number, and the
1
This practice is under the jurisdiction of ASTM Committee D20 on Plastics and ASTM specification to which it conforms.
is the direct responsibility of Subcommittee D20.24 on Plastic Building Products.
Current edition approved April 10, 2002. Published June 2002. Originally
published as D 4756 – 91. Last previous edition D 4745 – 96.
2 4
Annual Book of ASTM Standards, Vol 08.01. Annual Book of ASTM Standards, Vol 04.07.
3 5
Annual Book of ASTM Standards, Vol 08.04. Available from Council of American Building Officials, 5203 Leesburg Pike,
Falls Church, VA 22041.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
D 4756
FIG. 1 Crimper and Crimps on Siding FIG. 3 Nailslot Punch
FIG. 4 Zip Tool
FIG. 2 Panels and Accessories
7.4 Accessories:
5. Protection of Materials
7.4.1 Starter Strip—Of two types: for horizontal siding and
5.1 All vinyl siding and soffi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E3073-22(Guide)
Standard Guide for Development of Waste Management Plan for Construction, Deconstruction, or Demolition Projects

SIGNIFICANCE AND USE
4.1 There are many reasons to implement a CWM plan. The focus of this guide is development of CWM plans that describe intended waste management methods and preconstruction and construction procedures to facilitate the optimal management of discarded materials.  
4.2 A CWM plan includes, but is not limited to, requirements for documentation of the types and amounts of material generated, final disposition of the materials, and supporting evidence or statements as to the disposition (see 3.2.2).  
4.3 The users of this guide can include contractors, architects, engineers, building owners or their representatives, consultants, and government agencies, all of whom may have an interest in reducing construction site waste.  
4.4 Project teams should ensure they use recycling facilities (see 3.2.3) to recycle materials generated in their construction, deconstruction, or demolition projects.
SCOPE
1.1 The purpose of this guide is to facilitate development of a waste management plan for construction, deconstruction, or demolition projects (hereafter, construction waste management (CWM) plan).  
1.2 This guide applies to CWM plans developed for construction, renovation, deconstruction, and demolition of buildings, factories, parking structures, and any other structure, as well as above- and below-ground infrastructure.  
1.3 This guide includes CWM plan guidance for the wastes generated on-site during construction, deconstruction, and demolition projects.
Note 1: For example, included is any waste generated during these activities such as structural and finish materials and construction chemicals; construction product and materials packaging; construction office waste, including paper documents; wastes from site development work, such as excavated soils, rocks, vegetation, and stumps; and other ancillary items, such as broken tools, safety materials/personal protective equipment, and food and beverages and their packaging. The list of items above is offered for illustration purposes only; it is not intended to be fully inclusive of all materials from a construction, deconstruction, or demolition project that are suitable for reuse, repurposing, manufacturer reclamation, composting, or recycling.  
1.4 Waste generated in the manufacture, preparation, or fabrication of materials before delivery to the job site are not in the scope of this guide.  
1.5 This guide does not change or substitute for any federal, state, or local statutory or regulatory provisions or requirements including, but not limited to, those related to the handling, control, containment, transport, or disposition of any particular material.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    5 pages
    English language
    sale 15% off
  • Guide
    5 pages
    English language
    sale 15% off
ASTM
ASTM D7392-20(Practice)
Standard Practice for PM Detector and Bag Leak Detector Manufacturers to Certify Conformance with Design and Performance Specifications for Cement Plants

SIGNIFICANCE AND USE
5.1 EPA regulations require Portland cement plants that burn hazardous waste to use BLDs or PMDs to provide either a relative or an absolute indication of PM concentration and to alert the plant operator of the need to inspect PM control equipment or initiate corrective action. EPA and others have not established for these applications specific design and performance specifications for these instruments. The design and performance specifications and test procedures contained in this practice will help ensure that measurement systems are capable of providing reliable monitoring data.  
5.2 This practice identifies relevant information and operational characteristics of BLD and PMD monitoring devices for Portland cement kiln systems. This practice will assist equipment suppliers and users in the evaluation and selection of appropriate monitoring equipment.  
5.3 This practice requires that tests be conducted to verify manufacturer’s published specifications for detection limit, linearity, thermal stability, insensitivity to supply voltage variations and other factors so that purchasers can rely on the manufacturer’s published specifications. Purchasers are also assured that the specific instrument has been tested at the point of manufacture and shown to meet selected design and performance specifications prior to shipment.  
5.4 This practice requires that the manufacturer develop and provide to the user written procedures for installation start-up, operation, maintenance, and quality assurance of the equipment. This practice requires that these same procedures are used for a field performance demonstration of the BLD or PMD monitoring equipment at a Portland cement plant.  
5.5 The applicable test procedures and specifications of this practice are selected to address the equipment and activities that are within the control of the manufacturer.  
5.6 This practice also may serve as the basis for third party independent audits of the certification procedures used ...
SCOPE
1.1 This practice covers the procedure for certifying particulate matter detectors (PMDs) and bag leak detectors (BLDs) that are used to monitor particulate matter (PM) emissions from kiln systems at Portland cement plants that burn hazardous waste. It includes design specifications, performance specifications, test procedures, and information requirements to ensure that these continuous monitors meet minimum requirements, necessary in part, to monitor reliably PM concentrations to indicate the need for inspection or corrective action of the types of air pollution control devices that are used at Portland cement plants that burn hazardous waste.  
1.2 This practice applies specifically to the original manufacturer, or to those involved in the repair, remanufacture, or resale of PMDs or BLDs.  
1.3 This practice applies to (a) wet or dry process cement kilns equipped with electrostatic precipitators, and (b) dry process kilns, including pre-heater pre-calciner kiln systems, equipped with fabric filter controls. Some types of monitoring instruments are suitable for only certain types of applications.
Note 1: This practice has been developed based on careful consideration of the nature and variability of PM concentrations, effluent conditions, and the type, configuration, and operating characteristics of air pollution control devices used at Portland cement plants that burn hazardous waste.  
1.4 This practice applies to Portland cement kiln systems subject to PM emission standards contained in 40 CFR 63, Subpart EEE.
Note 2: The level of the PM emission limit is relevant to the design and selection of appropriate PMD and BLD instrumentation. The current promulgated PM emission standards (70 FR 59402, Oct. 12, 2005) are: (a) 65 mg/dscm at 7 % O2 (0.028 gr/dscf at 7 % O2) or approximately 30 mg/acm (0.013 gr/acf) for “existing sources” and (b) 5.3 mg/dscm at 7 % O2 (0.0023 gr/dscf at 7 % O2) or approximately 2.5 mg/ac...

  • Standard
    21 pages
    English language
    sale 15% off
  • Standard
    21 pages
    English language
    sale 15% off
ASTM
ASTM E2691-20(Practice)
Standard Practice for Job Productivity Measurement

SIGNIFICANCE AND USE
5.1 JPM produces two measurements: construction production rate and productivity.  
5.1.1 JPM measures the overall production rate by comparing CPIP to the time elapsed in the construction schedule.  
5.1.2 JPM measures overall job productivity through a comparison of labor usage to a reference point.  
5.2 JPM issues early warning signals for construction.  
5.2.1 JPM identifies productivity deviations in the form of any gains or losses in productivity, and anomalies indicating a special cause, from the productivity reference point.  
5.2.2 JPM measures the productivity changes to individual building elements (according to the UNIFORMAT II format for organizing building data, in Classification E1557) with the same methodology used for overall job productivity measurement.  
5.2.3 JPM measures ongoing changes in labor usage.  
5.3 JPM measures productivity wherever the labor is used in construction by:  
5.3.1 Any contractor or construction manager directly or indirectly responsible for the productivity of the labor and its usage.  
5.3.2 Any contractor or construction manager conducting self performance on any portion of the construction job.  
5.3.3 Any contractor or construction manager supervising labor performance on any portion of a construction job.
SCOPE
1.1 Based on the UNIFORMAT II format for organizing building data, established in Classification E1557, and depending on the level where measurement is applied (industry, total job, or building element), JPM measures construction productivity at three levels: task, project, and industry (shown in Fig. 1). By comparing labor hours used against CPIP, JPM allows for unified measurement of established building elements (according to the UNIFORMAT II format. This practice establishes a process for measuring construction job productivity by comparing labor usage to CPIP.
FIG. 1 Measurement of Productivity at the Industry, Project, and Task Level  
1.2 JPM measures labor productivity of the installation processes on a construction job.2  
1.3 CPIP is measured with input from the labor performing the installation, utilizing elements of statistical process control (SPC) and industrial engineering.  
1.4 JPM takes into account the difficulty of installation at any given point on a job.  
1.5 JPM evaluates relative productivity changes using trend monitoring.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    25 pages
    English language
    sale 15% off
  • Standard
    25 pages
    English language
    sale 15% off
ASTM
ASTM F3342-19(Guide)
Standard Guide for Temporary Fence Applications for Construction Sites

SIGNIFICANCE AND USE
5.1 This guide sets forth the minimum standard requirements for the application of temporary fences for construction sites by installing 6 or 8 ft (1.83 or 2.44 m) high temporary construction fence enclosures used to delineate and form a physical barrier on the construction site. A wide variety of materials, both new and used, are acceptable as long as the finished product is neat and uniform in appearance.  
5.2 Temporary fences should form a continuous barrier, panel type fence to be securely attached together or to a supporting post with steel fitting forming a positive connection.
Note 1: Warning to end user regarding screening: Wind screens applied to a fence form a solid barrier. The temporary fence described in this standard is not capable of handing 110 MPH wind gusts per ASCE/SEI 7-10. If screening is to be installed the fence should be researched and designed the same as a permanent fence to support the wind load; refer to Chain Link Manufacturers Institute Wind Load Guide, WLG 2445.
Note 2: Warning to end user regarding installations adjacent to open excavation and street corners. Refer to contract documents, site plans, or local codes for fence offset from excavations and to ensure vehicles a clear line of sight for street corner safety.
SCOPE
1.1 This guide covers a variety of materials and methods used in the construction of temporary fences.  
1.2 Temporary fences are physical barriers used to define and designate the boundary of construction sites.  
1.3 Temporary fences are intended to be installed before any construction activity starting and removed at the end of the construction phase. The duration of service can vary; consideration should be given to the length of time the temporary fence will be in use.  
1.4 When determining and specifying materials and installation methods, investigate contract specifications, contract documents, site plan fence location, and, possibly, local codes. Before installation, review and inspect existing site conditions. In some cases, a permanent fence installation should be used as temporary fencing.  
1.5 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1751-23(Specification)
Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Nonextruding and Resilient Asphalt Types)

SCOPE
1.1 This specification covers preformed expansion joint filler having relatively little extrusion and substantial recovery after release from compression.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
Note 1: Attention is called to Specifications D1752 and D994/D994M.  
1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM D8139-23(Specification)
Standard Specification for Semi-Rigid, Closed-Cell Polypropylene Foam, Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction

SCOPE
1.1 This specification covers preformed expansion joint fillers made from closed-cell polypropylene foam materials having suitable compressibility, recovery from compression, nonextruding, and weather-resistant characteristics.  
1.1.1 Type I, closed-cell polypropylene foam.  
1.2 These joint fillers are intended for use in concrete pavements in full-depth joints. There are several variations in size with typical thicknesses of 1/2 in. (12.7 mm), 3/4 in. (19.05 mm), and 1 in. (25.4 mm); typical widths of 31/2 in. (88.9 mm), 4 in. (101.6 mm), 5 in. (127 mm), 6 in. (152.5 mm), 7 in. (177.8 mm), 8 in. (203.2 mm), or 48 in. (1.2 m) sheet; and typical lengths of 5 ft (1.52 m) and 10 ft (3.05 m).  
1.3 The values stated in inch-pound units are to be regarded as the standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off