Standard Specification for Hydrocarbon Unleaded Aviation Gasoline

ABSTRACT
This specification establishes the requirements for purchases of Grade UL 91 unleaded aviation gasoline under contract and is intended primarily for use by purchasing agencies. It does not cover any other gasolines satisfactory for reciprocating aviation engines. The unleaded aviation gasoline, except as otherwise specified here, shall consist of blends of refined hydrocarbons derived from crude petroleum, natural gasoline, or blends thereof, with synthetic hydrocarbons or aromatic hydrocarbons, or both. Additives for electrical conductivity and corrosion inhibition, as well as certain types of antioxidants may be added separately, or in combination, in specified compositions and concentrations. Properly sampled specimens shall undergo test procedures and conform, accordingly, to the following requirements: knock value (motor octane number); density; distillation (initial boiling point, fuel evaporated, and final boiling point); recovery, residue and loss volumes; vapor pressure; freezing point; sulfur content; net heat of combustion; corrosion (copper strip); oxidation stability (potential gum); water reaction (volume change); and electrical conductivity.
SCOPE
1.1 This specification covers formulating specifications for purchases of aviation gasoline under contract and is intended primarily for use by purchasing agencies.  
1.2 Unleaded aviation gasoline defined by this specification is for use in engines and associated aircraft that are specifically approved by the engine and aircraft manufacturers. This fuel is not considered suitable for use in other engines and associated aircraft that are certified to use only leaded aviation gasolines of the same octane grade.  
1.3 This specification, unless otherwise provided, prescribes the required properties of unleaded aviation gasoline at the time and place of delivery.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Oct-2015
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D7547-15e1 - Standard Specification for Hydrocarbon Unleaded Aviation Gasoline
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D7547-15e1 - Standard Specification for Hydrocarbon Unleaded Aviation Gasoline
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:D7547 −15 An American National Standard
Standard Specification for
1
Hydrocarbon Unleaded Aviation Gasoline
This standard is issued under the fixed designation D7547; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Title of Table 1 was corrected editorially in December 2016.
1. Scope* D873 Test Method for Oxidation Stability of Aviation Fuels
(Potential Residue Method)
1.1 This specification covers formulating specifications for
D1094 Test Method for Water Reaction of Aviation Fuels
purchases of aviation gasoline under contract and is intended
D1298 Test Method for Density, Relative Density, or API
primarily for use by purchasing agencies.
Gravity of Crude Petroleum and Liquid Petroleum Prod-
1.2 Unleaded aviation gasoline defined by this specification
ucts by Hydrometer Method
is for use in engines and associated aircraft that are specifically
D2386 Test Method for Freezing Point of Aviation Fuels
approved by the engine and aircraft manufacturers.This fuel is
D2622 Test Method for Sulfur in Petroleum Products by
not considered suitable for use in other engines and associated
Wavelength Dispersive X-ray Fluorescence Spectrometry
aircraft that are certified to use only leaded aviation gasolines
D2624 Test Methods for Electrical Conductivity ofAviation
of the same octane grade.
and Distillate Fuels
1.3 Thisspecification,unlessotherwiseprovided,prescribes
D2700 Test Method for Motor Octane Number of Spark-
the required properties of unleaded aviation gasoline at the
Ignition Engine Fuel
time and place of delivery.
D3237 TestMethodforLeadinGasolinebyAtomicAbsorp-
tion Spectroscopy
1.4 The values stated in SI units are to be regarded as
D3338 Test Method for Estimation of Net Heat of Combus-
standard. No other units of measurement are included in this
tion of Aviation Fuels
standard.
D4052 Test Method for Density, Relative Density, and API
1.5 This standard does not purport to address all of the
Gravity of Liquids by Digital Density Meter
safety concerns, if any, associated with its use. It is the
D4057 Practice for Manual Sampling of Petroleum and
responsibility of the user of this standard to establish appro-
Petroleum Products
priate safety and health practices and determine the applica-
D4171 Specification for Fuel System Icing Inhibitors
bility of regulatory limitations prior to use.
D4177 Practice for Automatic Sampling of Petroleum and
2. Referenced Documents
Petroleum Products
2
D4306 Practice for Aviation Fuel Sample Containers for
2.1 ASTM Standards:
Tests Affected by Trace Contamination
D86 Test Method for Distillation of Petroleum Products and
D4529 Test Method for Estimation of Net Heat of Combus-
Liquid Fuels at Atmospheric Pressure
tion of Aviation Fuels
D130 Test Method for Corrosiveness to Copper from Petro-
D4809 Test Method for Heat of Combustion of Liquid
leum Products by Copper Strip Test
Hydrocarbon Fuels by Bomb Calorimeter (Precision
D323 TestMethodforVaporPressureofPetroleumProducts
Method)
(Reid Method)
D4865 Guide for Generation and Dissipation of Static Elec-
1 tricity in Petroleum Fuel Systems
This specification is under the jurisdiction of ASTM Committee D02 on
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of D5006 Test Method for Measurement of Fuel System Icing
Subcommittee D02.J0.02 on Spark and Compression Ignition Aviation Engine
Inhibitors (Ether Type) in Aviation Fuels
Fuels.
D5059 Test Methods for Lead in Gasoline by X-Ray Spec-
Current edition approved Nov. 1, 2015. Published November 2015. Originally
troscopy
approved in 2009. Last previous edition approved in 2014 as D7547 – 14b. DOI:
10.1520/D7547-15E01.
D5191 Test Method for Vapor Pressure of Petroleum Prod-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
ucts (Mini Method)
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D6469 GuideforMicrobialContaminationinFuelsandFuel
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Systems
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
D7547−15
NOTE 2—Addition of isopropyl alcohol (IPA) can reduce knock ratings
E29 Practice for Using Significant Digits in Test Data to
3
below minimum specification values (see X1.2.3).
Determine Conformance with Specifications
5.2.2.2 Di-Ethylene Glycol Monomethyl Ether (Di-EGME),
3. Terminology
confor
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D7547 − 15 D7547 − 15 An American National Standard
Standard Specification for
1
Hydrocarbon Unleaded Aviation Gasoline
This standard is issued under the fixed designation D7547; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Title of Table 1 was corrected editorially in December 2016.
1. Scope*
1.1 This specification covers formulating specifications for purchases of aviation gasoline under contract and is intended
primarily for use by purchasing agencies.
1.2 Unleaded aviation gasoline defined by this specification is for use in engines and associated aircraft that are specifically
approved by the engine and aircraft manufacturers. This fuel is not considered suitable for use in other engines and associated
aircraft that are certified to use only leaded aviation gasolines of the same octane grade.
1.3 This specification, unless otherwise provided, prescribes the required properties of unleaded aviation gasoline at the time
and place of delivery.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
D130 Test Method for Corrosiveness to Copper from Petroleum Products by Copper Strip Test
D323 Test Method for Vapor Pressure of Petroleum Products (Reid Method)
D873 Test Method for Oxidation Stability of Aviation Fuels (Potential Residue Method)
D1094 Test Method for Water Reaction of Aviation Fuels
D1298 Test Method for Density, Relative Density, or API Gravity of Crude Petroleum and Liquid Petroleum Products by
Hydrometer Method
D2386 Test Method for Freezing Point of Aviation Fuels
D2622 Test Method for Sulfur in Petroleum Products by Wavelength Dispersive X-ray Fluorescence Spectrometry
D2624 Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
D2700 Test Method for Motor Octane Number of Spark-Ignition Engine Fuel
D3237 Test Method for Lead in Gasoline by Atomic Absorption Spectroscopy
D3338 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4171 Specification for Fuel System Icing Inhibitors
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D4306 Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
D4529 Test Method for Estimation of Net Heat of Combustion of Aviation Fuels
D4809 Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method)
D4865 Guide for Generation and Dissipation of Static Electricity in Petroleum Fuel Systems
1
This specification is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.J0.02 on Spark and Compression Ignition Aviation Engine Fuels.
Current edition approved Nov. 1, 2015. Published November 2015. Originally approved in 2009. Last previous edition approved in 2014 as D7547 – 14b. DOI:
10.1520/D7547-15.10.1520/D7547-15E01.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
D7547 − 15
D5006 Test Method for Measurement of Fuel System Icing Inhibitors (Ether Type) in Aviation Fuels
D5059 Test Methods for Lead in Gasoline by X-Ray Spectroscopy
D5191 Test Method for Vapor Pressure of Petroleum Products (Mini Method)
D6469 Guide for Microbial Contamination
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.