ASTM D3498-19a
(Specification)Standard Specification for Adhesives for Field-Gluing Wood Structural Panels (Plywood or Oriented Strand Board) to Wood Based Floor System Framing
Standard Specification for Adhesives for Field-Gluing Wood Structural Panels (Plywood or Oriented Strand Board) to Wood Based Floor System Framing
ABSTRACT
This specification covers minimum performance standards and test requirements for gap-filling construction adhesives for field-gluing plywood to lumber framing for floor systems. The adhesive shall conform to the strength and durability properties prescribed. The different methods for specimen's preparation are presented in details. The shear strength, gap-filling effect on strength, and durability shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers minimum performance standards and test requirements for gap-filling construction adhesives for bonding wood structural panels consisting of plywood or oriented strand board (OSB) to wood based floor system framing, particularly dimension lumber or wood I-joists, at the construction site.
1.2 This specification provides a basis for ensuring the quality of the adhesives and is not intended as an application specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D3498 −19a
Standard Specification for
Adhesives for Field-Gluing Wood Structural Panels
(Plywood or Oriented Strand Board) to Wood Based Floor
1
System Framing
This standard is issued under the fixed designation D3498; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D572Test Method for Rubber—Deterioration by Heat and
Oxygen
1.1 This specification covers minimum performance stan-
D905Test Method for Strength Properties of Adhesive
dards and test requirements for gap-filling construction adhe-
Bonds in Shear by Compression Loading
sivesforbondingwoodstructuralpanelsconsistingofplywood
D907Terminology of Adhesives
or oriented strand board (OSB) to wood based floor system
D4300Test Methods for Ability of Adhesive Films to
framing, particularly dimension lumber or wood I-joists, at the
Support or Resist the Growth of Fungi
construction site.
D4442Test Methods for Direct Moisture Content Measure-
1.2 This specification provides a basis for ensuring the
ment of Wood and Wood-Based Materials
quality of the adhesives and is not intended as an application
D4783Test Methods for Resistance of Adhesive Prepara-
specification.
tions in Container toAttack by Bacteria,Yeast, and Fungi
E4Practices for Force Verification of Testing Machines
1.3 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical E177Practice for Use of the Terms Precision and Bias in
ASTM Test Methods
conversions to SI units that are provided for information only
3
and are not considered standard.
2.2 Voluntary Product Standards:
PS1Structural Plywood
1.4 The following precautionary caveat pertains only to the
PS2Performance Standard for Wood-Based Structural-Use
test method portion, Section 11, of this specification: This
Panels
standard does not purport to address all of the safety concerns,
if any, associated with its use. It is the responsibility of the user
3. Terminology
of this standard to establish appropriate safety, health, and
environmental practices and determine the applicability of
3.1 Definitions:
regulatory limitations prior to use.
3.1.1 Many terms in this specification are defined in Termi-
1.5 This international standard was developed in accor-
nology D907.
dance with internationally recognized principles on standard-
3.1.2 gap class, n—a classification used to indicate whether
1
ization established in the Decision on Principles for the
a product has been qualified using a ⁄8in. (1.59 mm) gap
Development of International Standards, Guides and Recom-
condition.
mendations issued by the World Trade Organization Technical
3.1.3 gap-filling adhesive, n—an adhesive capable of form-
Barriers to Trade (TBT) Committee.
ing and maintaining a bond between surfaces that are not
close-fitting.
2. Referenced Documents
3.1.3.1 Discussion—Close-fitting is relative to a given ma-
2
2.1 ASTM Standards:
terial and industry; for example, standards in construction
differ from standards in electronics. Some adhesives will bond
bybridgingwithoutcompletelyfillingthegap;othersbyfilling
1
This specification is under the jurisdiction of ASTM Committee D14 on
the gap completely.
Adhesives and is the direct responsibility of Subcommittee D14.70 on Construction
3.1.4 open assembly time, n—the time interval between
Adhesives.
Current edition approved June 1, 2019. Published June 2019. Originally
applying adhesive on the substrates and closing them together
approved in 1976. Last previous edition approved in 2019 as D3498–19. DOI:
before bonding.
10.1520/D3498-19a.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from National Institute of Standards and Technology (NIST), 100
the ASTM website. Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3498−19a
3.1.5 oriented strand board (OSB), n—a mat formed panel 6. Materials
product with oriented layers resulting in directional properties.
6.1 The adhesive shall be a gap-filling construction adhe-
3.1.6 panel type, n—aclassificationusedtoindicatewhether
sive.
aproducthasbeenqualifiedusingOSBand/orplywoodpanels.
6.2 T
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3498 − 19 D3498 − 19a
Standard Specification for
Adhesives for Field-Gluing Wood Structural Panels
(Plywood or Oriented Strand Board) to Wood Based Floor
1
System Framing
This standard is issued under the fixed designation D3498; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers minimum performance standards and test requirements for gap-filling construction adhesives for
bonding wood structural panels consisting of plywood or oriented strand board (OSB) to wood based floor system framing,
particularly dimension lumber or wood I-joists, at the construction site.
1.2 This specification provides a basis for ensuring the quality of the adhesives and is not intended as an application
specification.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory
limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D572 Test Method for Rubber—Deterioration by Heat and Oxygen
D905 Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading
D907 Terminology of Adhesives
D4300 Test Methods for Ability of Adhesive Films to Support or Resist the Growth of Fungi
D4442 Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
D4444 Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
D4783 Test Methods for Resistance of Adhesive Preparations in Container to Attack by Bacteria, Yeast, and Fungi
E4 Practices for Force Verification of Testing Machines
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
3
2.2 Voluntary Product Standards:
PS1 Structural Plywood
PS2 Performance Standard for Wood-Based Structural-Use Panels
3. Terminology
3.1 Definitions:
3.1.1 Many terms in this specification are defined in Terminology D907.
1
This specification is under the jurisdiction of ASTM Committee D14 on Adhesives and is the direct responsibility of Subcommittee D14.70 on Construction Adhesives.
Current edition approved March 1, 2019June 1, 2019. Published March 2019June 2019. Originally approved in 1976. Last previous edition approved in 20182019 as
D3498 – 18a.D3498 – 19. DOI: 10.1520/D3498-19.10.1520/D3498-19a.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from National Institute of Standards and Technology (NIST), 100 Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3498 − 19a
1
3.1.2 gap class, n—a classification used to indicate whether a product has been qualified using a ⁄8 in. (1.59 mm) gap condition.
3.1.3 gap-filling adhesive, n—an adhesive capable of forming and maintaining a bond between surfaces that are not close-fitting.
3.1.3.1 Discussion—
Close-fitting is relative to a given material and industry; for example, standards in construction differ from standards in electronics.
Some adhesives will bond by bridging without completely filling the gap; others by filling the gap completely.
3.1.4 open assembly time, n—the time interval between applying adhesive on the substrates and closing them together before
bonding.
3.1.5 ori
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.