iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1330-91(2006)

(Guide)

Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe

Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe

SIGNIFICANCE AND USE
The maximum length and minimum diameter of the pipe shall be determined by the capacity of the blast equipment used.
This guide is recommended for removing mill scale, rust scale, paints, zincs, and oxides.
SCOPE
1.1 This guide covers metallic abrasive blasting to descale the interior of carbon steel pipe.
1.2 This guide is recommended for use in conjunction with an abrasive reclamation system.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
30-Nov-2006
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.11 - Machinery and Piping Systems
Current Stage
Ref Project

Relations

Replaces
ASTM F1330-91(2001) - Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe
Effective Date
01-Dec-2006
Replaced By
ASTM F1330-91(2012) - Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe
Effective Date
01-May-2012
Referred By
ASTM B874-96(2018) - Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
Effective Date
01-Dec-2006

Buy Standard

ASTM F1330-91(2006) - Standard Guide for Metallic Abrasive Blasting to Descale the Interior of PipeASTM F1330-91(2006) - Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe
PreviousNext
Guide
ASTM F1330-91(2006) - Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F1330 – 91 (Reapproved 2006)
Standard Guide for
Metallic Abrasive Blasting to Descale the Interior of Pipe
This standard is issued under the fixed designation F1330; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Significance and Use
1.1 This guide covers metallic abrasive blasting to descale 3.1 Themaximumlengthandminimumdiameterofthepipe
the interior of carbon steel pipe. shall be determined by the capacity of the blast equipment
1.2 This guide is recommended for use in conjunction with used.
an abrasive reclamation system. 3.2 Thisguideisrecommendedforremovingmillscale,rust
1.3 The values stated in SI units are to be regarded as the scale, paints, zincs, and oxides.
standard. The values given in parentheses are for information
4. General Requirements
only.
4.1 Before blasting, pipe shall be dry and free of slag and
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the weldspatterwhichwouldnotberemovedbyabrasiveblasting.
Pipe shall also be free of loose dust and debris which might
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica- hamper the effectiveness of abrasive blasting.
4.2 Abrasive blasting shall be accomplished in a dry area
bility of regulatory limitations prior to use.
with the ambient air condition such that condensation does not
2. Referenced Documents
occur.
2.1 ASTM Standards: 4.3 Shot and blasting equipment shall be stored at a tem-
D2200 Practice for Use of Pictorial Surface Preparation perature not less than −13°C (10°F) above the dew point of the
Standards and Guides for Painting Steel Surfaces surrounding area.
E18 Test Methods for Rockwell Hardness of Metallic Ma- 4.3.1 Abrasive reclamation system shall include a filtration
terials system capable of removing oxides, debris, dust, shot/grit
2.2 SAE Standards: fragments, and fines.
J444 Cast Shot and Grit Size Specifications for Peening 4.4 Compressed air system shall be equipped with moisture
Cleaning removaldevicescapableofreducingthedewpointoftheairat
J827 Cast Steel Shot the nozzle to −18°C (approximately 0°F) or less.
2.3 Other Documents: 4.5 Hoses shall have the maximum practical diameter and
SSPC SP10 Surface Preparation Specifications shall be as short as possible.
SFSA 20-66 Standard Specification for Cast Steel Abra- 4.6 Nozzles shall have the maximum possible aperture as
sives determined by the capacity of the blast equipment and as
limited by the pipe diameter.
4.7 Internal pipe cleaning nozzle assemblies are commer-
This guide is under the jurisdiction of ASTM Committee F25 on Ships and
cially available and shall be used where required.
Marine Technology and is the direct responsibility of Subcommittee F25.11 on
4.7.1 Internal pipe cleaning nozzle assemblies shall include
Machinery and Piping Systems.
Current edition approved Dec. 1, 2006. Published January 2007. Originally
a carriage which is capable of centering the nozzle concentri-
approved in 1991. Last previous edition approved in 2001 as F1330–91 (2001).
callyinthepipebeingblastedandanozzlewhichiscapableof
DOI: 10.1520/F1330-91R06.
producing a consistent 360° blast pattern.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4.7.2 Diagrams of some commercially available internal
Standards volume information, refer to the standard’s Document Summary page on
pipe cleaning assemblies are provided in Figs. 1-4.
the ASTM website.
4.7.3 If a lance is required, it shall be at least as long as the
Available from Society of Automotive Engineers (SAE), 400 Commonwealth
pipe being blasted.
Dr., Warrendale, PA 15096-0001, http://www.sae.org.
Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,
4.8 Blasting shall be accomplished using an abrasive mix-
Pittsburgh, PA 15222-4656, http://www.sspc.org.
ture of cast steel shot and grit, or with iron shot or grit.
Available from Steel Founders’Society ofAmerica (SFSA), 780 McArdle Dr.,
4.8.1 Iron or grit may be used if desired.
Unit G, Crystal Lake, IL 60014, http://www.sfsa.org.
Copyright ©ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA19428-2959, United States.
F1330 – 91 (2006)
A,B
TABLE 1 Steel Shot and Grit Specifications
Property Shot Grit
Size:
New abrasive as All material is screened to meet or exceed SAE J444
manufactured and SFSA 20-66.
Chemistry:
Carbon 0.85 to 1.20 %
FIG. 1 For 20- to 50-mm (Approximately ⁄4- to 2-in.) Inside
Manganese 0.60 to 1.00 %
Diameter Pipe
Silicon 0.50 to 1.00 %
Sulfur <0.05 %
Phosphorus <0.05 %
Microstructure:
Uniformly tempered martensite, with fine, well-distributed carbides, if any.
Carbide networks, transformation products, decarburized surfaces,
inclusions, and quench cracks are undesirables.
Hardness:
D
Commonly used 40 to 50 RC 40 to 50 RC
C
structural steel 40 to 60 RC
A
Courtesy of Steel Structures Painting Council.
B
It is extremely important that contractual documents which specify abrasive to
be used clearly designate the abrasive by size and by hardness.
FIG. 2 For 50- to 125-mm (Approximately 2- to 5-in.) Inside
C
Bothcaststeelshotandgritofhardnessesintherangefrom30to66Rockwell
Diameter Pipe
Cmaybepurchased.However,theabrasivesoflessthan40RCandgreaterthan
60 RC are generally used for applications other than surface preparation of
structural steel.
D
Abrasivemanufacturersidentifysteelgritbydesignationswhichincludetwoor
moreprefixletters,followedbythenumbersize.Prefixlettersaredifferentforeach
of the abrasive suppliers for any given hardn
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F1330-91(2023)(Guide)
Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe

SIGNIFICANCE AND USE
3.1 The maximum length and minimum diameter of the pipe shall be determined by the capacity of the blast equipment used.  
3.2 This guide is recommended for removing mill scale, rust scale, paints, zincs, and oxides.
SCOPE
1.1 This guide covers metallic abrasive blasting to descale the interior of carbon steel pipe.  
1.2 This guide is recommended for use in conjunction with an abrasive reclamation system.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1199-21(Specification)
Standard Specification for Cast (All Temperatures and Pressures) and Welded Pipe Line Strainers (150 psig and 150°F Maximum)

ABSTRACT
This specification provides the minimum requirements for the design, fabrication, rating, marking, and testing of all cast pipe line strainers, and welded pipe line strainers used in services up to 150 psig and 150°F (1 MPa and 65°C) that are acceptable for use in marine environments. The strainers may be classified into three general construction categories, namely, simplex, duplex (or multiplex), and automatic (self-cleaning). They may also be further classified according to pressure ratings and types of port connections, port alignments relative to unit center lines, cover closures, valve types (in duplex), types of baskets or elements, materials of construction, and other features of design.
SCOPE
1.1 This specification covers all cast strainers and welded strainers in services up to 150 psig and 150°F (1 MPa and 65°C). For welded strainers used in services above 150 psig and 150°F, see Specification F1200.  
1.2 This standard provides the minimum requirements for the design, fabrication, rating, marking, and testing of cast and welded pipe line strainers for services above 0°F (−18°C).  
1.3 Strainers manufactured to this specification are acceptable for use in the marine environment.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1200-21a(Specification)
Standard Specification for Fabricated (Welded) Pipe Line Strainers (Above 150 psig and 150°F (1 MPa and 65°C))

ABSTRACT
This specification covers welded pipe line strainers for use in applications above 150 psig and 150 F as well as in marine environment conditions. Strainers covered in this specification are classified into simplex, duplex (or multiplex), and automatic (self-cleaning) based on general construction. However, other bases for further classifying strainers are available: pressure ratings and types of port connection, port alignments relative to unit center lines, cover closures, valve types (in duplex), types of baskets or elements, materials of construction, and other design features. Strainers shall be manufactured by casting or forging or fabricated from plates, tubes, or pipes, with inlet and outlet connections requiring welding joined by butt welding. On the other hand, strainers made of carbon or low alloy steel shall be post-weld heat treated. The strainers shall undergo either hydrostatic or air test, while the welds shall be examined visually or radiographically. All tests shall conform to the requirements specified.
SCOPE
1.1 This specification covers welded strainers in services above 150 psig or 150°F (1 MPa and 65°C). For welded strainers in services at or below these ratings and cast strainers, see Specification F1199.  
1.2 This specification provides the minimum requirements for the design fabrication, rating, marking, and testing of welded pipe line strainers for services above 150 psig or 150°F (1 MPa and 65°C).  
Note 1: Fabricated (welded) pipe line strainers meeting this standard may also be used at pressures of 150 psig (1 MPa) and below and 0°F (–18°C) and above.  
1.3 Strainers manufactured to this specification are acceptable for use in the marine environment.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 8, of this specification.  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1155-10(2019)(Practice)
Standard Practice for Selection and Application of Piping System Materials

ABSTRACT
This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction. The materials and limitations listed in this specification meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and should be considered to be the minimum acceptable materials in regard to material, design, and testing.
SCOPE
1.1 This practice is intended as a guide to shipbuilders, shipowners, and design agents for use in the preparation of piping system material schedules for commercial ship design and construction.  
1.2 The materials and limitations listed in Tables 1-28 meet the minimum requirements of the U.S. Coast Guard and the American Bureau of Shipping and, except for titanium, should be considered to be the minimum acceptable materials in regard to material, design, and testing. This document is not intended to limit the selection of material strictly to those listed. Other equal or superior materials may be used provided that they are acceptable to the regulatory bodies and classification societies.  
Note 1: Titanium has been added as its use in fresh and sea water systems is becoming more common.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    24 pages
    English language
    sale 15% off
ASTM
ASTM A888-24(Specification)
Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

ABSTRACT
This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage. The pipe and fittings shall be iron castings suitable for installation and service for sanitary, storm drain, waste, and vent piping applications. The pipe and fittings shall meet all applicable requirements and tests given in this specification. Tensile test and chemical test shall be made to conform to the requirements specified. The pipe and fittings shall be uniformly coated with a material suitable for the purpose that is adherent, not brittle, and without a tendency to scale.
SCOPE
1.1 This specification covers hubless cast iron soil pipe and fittings for use in gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe and fittings. These pipe and fittings are intended for non-pressure applications, as the selection of the proper size for sanitary drain, waste, vent, and storm drain systems allows free air space for gravity drainage.  
1.2 The EDP/ASA numbers indicated in this section represent a Uniform Industry Code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are either new, special, or transitory and will be assigned numbers on subsequent prints of this specification.  
1.3 This specification covers pipe and fittings of the following patterns and applies to any other patterns that conform with the dimensions found in Tables 1 and 2 and all other applicable requirements given in this specification.2  
1.3.1 Lengths:    
Figures  
EDP/ASA Identification Numbers
for Hubless Pipe  
Fig. 1  
10 ft (3.0 m) in sizes and 5 ft. (1.5 m)
11/2 , 2, 3, 4, 5, 6, 8,
10, 12, and 15 in.  
Fig. 1, Fig. 2  
Method of Specifying Fittings  
Fig. 3  
1.3.2 Fittings:    
Quarter Bend  
Fig. 5  
Quarter Bend, Reducing  
Fig. 6  
Quarter Bend, with Side Opening  
Fig. 7  
Quarter Bend, with Heel Opening  
Fig. 8  
Quarter Bend, Tapped  
Fig. 9  
Quarter Bend, Double  
Fig. 10  
Quarter Bend, Long  
Fig. 11  
Short Sweep  
Fig. 12  
Long Sweep  
Fig. 13  
Long Sweep, Reducing  
Fig. 14  
Fifth Bend  
Fig. 15  
Sixth Bend  
Fig. 16  
Eighth Bend  
Fig. 17  
Eighth Bend, Long  
Fig. 18  
Sixteenth Bend  
Fig. 19  
Sanitary Tee  
Fig. 20  
Sanitary Tee with Side Opening  
Fig. 21  
Sanitary Tee with 2 in. Side Opening R or L/R and L  
Fig. 22  
Sanitary Tee, New Orleans Special with Side Opening  
Fig. 23  
Sanitary Tee with 45° Side Openings and New Orleans  
Fig. 24  
Sanitary Special Tee Tapped  
Fig. 25  
Sanitary Tapped Tee, Horizontal Twin  
Fig. 26  
Sanitary Tapped Tee, Double Vertical  
Fig. 27  
Y Branch  
Fig. 28  
Y Branch, Double  
Fig. 29  
Y Branch, Upright  
Fig. 30  
Upright Y Wide Center Florida Special  
Fig. 31  
Y Branch, Combination 1/8 Bend  
Fig. 32  
Y Branch, Combination 1/8 Bend Double  
Fig. 33  
Sanitary Cross  
Fig. 34  
Sanitary Cross with Side Opening  
Fig. 35  
Sanitary Cross, New Orleans, with Side Openings  
Fig. 36  
Sanitary Cross, New Orleans, with 45° Special and
Regular Side Openings  
Fig. 37  
Sanitary Cross, Tapped  
Fig. 38  
Test Tee  
Fig. 39  
Tapped Extension Piece  
Fig. 40  
Increaser-Reducer  
Fig. 41  
...

  • Technical specification
    63 pages
    English language
    sale 15% off
  • Technical specification
    63 pages
    English language
    sale 15% off
ASTM
ASTM F2769-24(Specification)
Standard Specification for Polyethylene of Raised Temperature (PE-RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

ABSTRACT
This specification covers the requirements for polyethylene of raised temperature (PE-RT) plastic hot- and cold-water tubing and distribution systems components made in one standard dimension ratio and intended for specified water service pressures and maximum working temperatures. The components covered here are comprised of tubing, fittings, valves, and manifolds intended for use in residential and commercial, hot and cold, potable water distribution systems. The polyethylene used to make tubing shall be virgin plastic and/or reworked plastic, while fittings shall be made from materials that are generally regarded as corrosion resistant. Sampled specimens shall be tested for conformance with workmanship, dimension (out-of-roundness, outside diameter, and wall thickness), burst pressure, sustained pressure, oxidative stability in potable chlorinated water, thermocycling, bend strength, excessive temperature-pressure capacity, environmental stress cracking, adhesion, and slow crack growth resistance requirements.
SCOPE
1.1 This specification establishes requirements for polyethylene of raised temperature (PE-RT) plastic hot- and cold-water tubing and distribution systems components made in one standard dimension ratio and intended for 100 psig (6.9 bar) water service up to and including a maximum working temperature of 180 °F (82 °C). Components are comprised of tubing, fittings, valves and manifolds. Tubing may incorporate an optional polymeric inner, middle or outer layer. Testing of fittings and PE-RT tubing to the requirements of this standard indicate that these fittings are appropriate for use with PE-RT piping systems. Requirements and test methods are included for materials, workmanship, dimensions and tolerances, burst pressure, sustained pressure, oxidative resistance, temperature cycling tests, bend strength and environmental stress cracking. Also included are tests related to system malfunctions. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems, and building supply lines.  
1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
Note 1: Suggested hydrostatic design stresses and hydrostatic pressure ratings for tubing and fittings are listed in Appendix X1. UV labeling guidelines are provided in Appendix X2. Design, assembly, and installation considerations are provided in Appendix X3. An optional performance qualification and an in-plant quality control program are recommended in Appendix X4.  
1.3 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off
ASTM
ASTM F1330-91(2023)(Guide)
Standard Guide for Metallic Abrasive Blasting to Descale the Interior of Pipe

SIGNIFICANCE AND USE
3.1 The maximum length and minimum diameter of the pipe shall be determined by the capacity of the blast equipment used.  
3.2 This guide is recommended for removing mill scale, rust scale, paints, zincs, and oxides.
SCOPE
1.1 This guide covers metallic abrasive blasting to descale the interior of carbon steel pipe.  
1.2 This guide is recommended for use in conjunction with an abrasive reclamation system.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM A961/A961M-23(Specification)
Standard Specification for Common Requirements for Steel Flanges, Forged Fittings, Valves, and Parts for Piping Applications

ABSTRACT
This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications. If the primary melting is required it shall incorporate separate degassing or refining and may be followed by secondary melting, such as electroslag remelting or vacuum remelting. If secondary melting is employed, the heat shall be defined as all of the ingot remelted from a single primary heat. Material requiring heat treatment shall be treated as specified in the individual product specification using the following procedures such as full annealing, solution annealing, isothermal annealing, normalizing, tempering and post-weld heat treatment, stress relieving. Heat analysis shall be used to determine the percentages of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, molybdenum, titanium, tantalum, copper, cobalt, nitrogen, aluminum, vanadium, cerium to meet the required chemical composition. The product analysis shall be used to determine if the chemical composition shall conform to the limits of the product specified. Mechanical tests shall be performed to determine the mechanical properties such as hardness, tensile properties, and impact properties.
SCOPE
1.1 This specification covers a group of common requirements that shall apply to steel flanges, forged fittings, valves, and parts for piping applications under any of the following individual product specifications:    
Title of Specification  
ASTM Designation  
Forgings, Carbon Steel, for Piping Components  
A105/A105M  
Forgings, Carbon Steel, for General-Purpose Piping  
A181/A181M  
Forged or Rolled Alloy-Steel Pipe Flanges, Forged  
A182/A182M  
Fittings, and Valves and Parts for High Temperature
Service  
Forgings, Carbon and Low Alloy Steel, Requiring Notch  
A350/A350M  
Toughness Testing for Piping Components  
Forged or Rolled 8 and 9 % Nickel Alloy  
A522/A522M  
Steel Flanges, Fittings, Valves, and Parts  
for Low-Temperature Service  
Forgings, Carbon and Alloy Steel, for Pipe Flanges,  
A694/A694M  
Fittings, Valves, and Parts for High-Pressure
Transmission Service  
Flanges, Forged, Carbon and Alloy Steel for Low  
A707/A707M  
Temperature Service  
Forgings, Carbon Steel, for Piping Components with  
A727/A727M  
Inherent Notch Toughness  
Forgings, Titanium-Stabilized Carbon Steel, for  
A836/A836M  
Glass-Lined Piping and Pressure Vessel Service  
1.2 In case of conflict between a requirement of the individual product specification and a requirement of this general requirement specification, the requirements of the individual product specification shall prevail over those of this specification.  
1.3 By mutual agreement between the purchaser and the supplier, additional requirements may be specified (see Section 4.1.2). The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order as agreed upon between the purchaser and supplier.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text and the tables, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply, unless the “M” designation (SI) of the product specification is specified in the order.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    9 pages
    English language
    sale 15% off
  • Technical specification
    9 pages
    English language
    sale 15% off
ASTM
ASTM C828-23(Test Method)
Standard Test Method for Low-Pressure Air Test of Vitrified Clay Pipe Lines

ABSTRACT
This test method contains procedures using low-pressure air for testing the integrity of installed vitrified clay pipe lines such as gravity-flow sewer pipes. The procedures detailed here should be performed on lines after adequately and properly plugging and bracing connection laterals, if any, and after the trenches are backfilled for a sufficient time. This test method can also be used as a preliminary test to demonstrate the condition of the line prior to backfill and further construction activities.
SCOPE
1.1 This test method defines procedures for testing vitrified clay pipe lines, using low-pressure air, to demonstrate the integrity of the installed line. Refer to Practice C12.  
1.2 This test method shall be performed on lines after connection laterals, if any, have been plugged and braced adequately to withstand the test pressure, and after the trenches have been backfilled for a sufficient time to generate a significant portion of the ultimate trench load on the pipe line. The time between completion of the backfill operation and low-pressure air testing shall be determined by the approving authority.  
1.3 This test method may also be used as a preliminary test, which enables the installer to demonstrate the condition of the line prior to backfill and further construction activities.  
1.4 This test method is suitable for testing gravity-flow sewer pipe constructed of vitrified clay or combinations of clay and other pipe materials.  
1.5 Terminology C896 is to be used for clarification of terminology in this test method.  
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM B1020/B1020M-22(Specification)
Standard Specification for Seamless Nickel Alloy Mechanical Tubing and Hollow Bar

SCOPE
1.1 This specification covers seamless nickel alloy tubing for use in mechanical applications or as hollow bar for use in the production of hollow components such as, but not limited to, nozzles, reducers, and couplings by machining where corrosion-resistant or high-temperature strength is needed. The grades covered are listed in Table 1.  
1.2 This specification covers seamless cold-finished mechanical tubing and hollow bar, and seamless hot-finished mechanical tubing and hollow bar in sizes up to 123/4 in. [325 mm] in outside nominal diameter (for round tubing) with wall thicknesses or inside diameters as required.  
1.3 Optional supplementary requirements are provided and when desired, shall be stated in the order.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off