iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E1795-04

(Specification)

Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings

Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings

ABSTRACT
This specification covers minimum material performance requirements and laboratory test procedures for nonreinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. Three types of nonreinforced liquid coating encapsulation products are presented: type I - encapsulation products intended for interior use, type II - encapsulation products intended for exterior use, and type III - encapsulation products intended for either interior or exterior use. The impact resistance, adhesion, dry abrasion resistance, water vapour transmission, water and chemical resistance, surface burning characteristics, and volatile organic compound content shall be tested to meet the requirements prescribed. Weathering, aging, scrub resistance, mildew resistance, paintability/repairability, flexibility, and tensile properties shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers minimum material performance requirements and laboratory test procedures for non-reinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. Performance properties addressed in this specification are:
1.1.1 Impact resistance,
1.1.2 Adhesion,
1.1.3 Dry Abrasion Resistance,
1.1.4 Water Vapor Transmission,
1.1.5 Water and Chemical Resistance,
1.1.6 Surface Burning Characteristics,
1.1.7 Volatile Organic Compound (VOC) Content,
1.1.8 Weathering,
1.1.9 Aging,
1.1.10 Scrub Resistance,
1.1.11 Mildew Resistance,
1.1.12 Paintability/Repairability,
1.1.13 Flexibility, and
1.1.14 Tensile Properties.
1.2 This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E 1796.
1.3 This specification complements Specification E 1797 for reinforced liquid coating encapsulation products.
1.4 This specification does not cover the use of encapsulation products on industrial steel structures nor on residential coated metal surfaces because no corrosion control requirements are included.
1.5 This specification applies to any non-reinforced liquid applied product that relies primarily on adhesion for attachment to the surface. These products are used to encapsulate a leaded paint surface with the intent of reducing human exposure to lead.
1.6 The results of the test methods included in this specification will not necessarily predict field performance.
1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

Status
Historical
Publication Date
31-Mar-2004
ICS
87.040 - Paints and varnishes
Technical Committee
E06 - Performance of Buildings
Current Stage
Ref Project

Relations

Replaces
ASTM E1795-00 - Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
Effective Date
01-Apr-2004
Replaced By
ASTM E1795-12 - Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
Effective Date
01-Apr-2012
Referred By
ASTM G195-22 - Standard Guide for Conducting Wear Tests Using a Rotary Platform Abraser
Effective Date
01-Apr-2004
Referred By
ASTM E1797-12(2017)e1 - Standard Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
Effective Date
01-Apr-2004
Referred By
ASTM E1796-20 - Standard Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings
Effective Date
01-Apr-2004
Referred By
ASTM E2252-22 - Standard Practice for Selection of Lead Hazard Reduction Methods for Identified Risks in Residential Housing or Child Occupied Facilities
Effective Date
01-Apr-2004

Buy Standard

ASTM E1795-04 - Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in BuildingsASTM E1795-04 - Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
PreviousNext
Technical specification
ASTM E1795-04 - Standard Specification for Non-Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1795 – 04
Standard Specification for
Non-Reinforced Liquid Coating Encapsulation Products for
1
Leaded Paint in Buildings
This standard is issued under the fixed designation E1795; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.6 The results of the test methods included in this specifi-
cation will not necessarily predict field performance.
1.1 This specification covers minimum material perfor-
1.7 The values stated in SI units are to be regarded as the
mance requirements and laboratory test procedures for non-
standard. The values given in parentheses are for information
reinforced liquid coating encapsulation products (single or
only.
multiple-coat systems) for leaded paint in buildings. Perfor-
1.8 This standard does not purport to address all of the
mance properties addressed in this specification are:
safety concerns, if any, associated with its use. It is the
1.1.1 Impact resistance,
responsibility of the user of this standard to establish appro-
1.1.2 Adhesion,
priate safety and health practices and determine the applica-
1.1.3 Dry Abrasion Resistance,
bility of regulatory requirements prior to use.
1.1.4 Water Vapor Transmission,
1.1.5 Water and Chemical Resistance,
2. Referenced Documents
1.1.6 Surface Burning Characteristics,
2
2.1 ASTM Standards:
1.1.7 Volatile Organic Compound (VOC) Content,
D16 Terminology for Paint, Related Coatings, Materials,
1.1.8 Weathering,
and Applications
1.1.9 Aging,
D522 Test Methods for Mandrel Bend Test of Attached
1.1.10 Scrub Resistance,
Organic Coatings
1.1.11 Mildew Resistance,
D823 Practices for Producing Films of Uniform Thickness
1.1.12 Paintability/Repairability,
of Paint, Varnish, and Related Products on Test Panels
1.1.13 Flexibility, and
D1005 Test Method for Measurement of Dry-Film Thick-
1.1.14 Tensile Properties.
ness of Organic Coatings Using Micrometers
1.2 This specification does not address the selection of an
D1186 Test Methods for Nondestructive Measurement of
encapsulation product for specific use conditions. Specific use
Dry Film Thickness of Nonmagnetic Coatings Applied to
conditions may require performance values other than those
3
a Ferrous Base
stated in this specification. See Guide E1796.
D1212 Test Methods for Measurement of Wet Film Thick-
1.3 This specification complements Specification E1797 for
ness of Organic Coatings
reinforced liquid coating encapsulation products.
D1308 Test Method for Effect of Household Chemicals on
1.4 This specification does not cover the use of encapsula-
Clear and Pigmented Organic Finishes
tion products on industrial steel structures nor on residential
D1475 Test Method For Density of Liquid Coatings, Inks,
coated metal surfaces because no corrosion control require-
and Related Products
ments are included.
D1653 Test Methods for Water Vapor Transmission of
1.5 This specification applies to any non-reinforced liquid
Organic Coating Films
applied product that relies primarily on adhesion for attach-
D2370 Test Method forTensile Properties of Organic Coat-
ment to the surface. These products are used to encapsulate a
ings
leaded paint surface with the intent of reducing human expo-
D2486 Test Methods for Scrub Resistance of Wall Paints
sure to lead.
1 2
This specification is under the jurisdiction of ASTM Committee E06 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Performance of Buildings and is the direct responsibility of Subcommittee E06.23 contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
on Lead Hazards Associated with Buildings. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved April 1, 2004. Published April 2004. Originally the ASTM website.
3
approved in 1995. Last previous edition approved in 2000 as E1795–00. DOI: Withdrawn. The last approved version of this historical standard is referenced
10.1520/E1795-04. on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E1795 – 04
D2794 Test Method for Resistance of Organic Coatings to 4.2 Type II: Exterior Use Only—Type II defines encapsula-
the Effects of Rapid Deformation (Impact) tion products intended for exterior use. These products shall
D3273 Test Method for Resistance to Growth of Mold on meet the requirements of this specification except that for
the Surface of Interior Coatings in an Environmental interior aging (that is, test method described in 10.10.2 not
Chamber conducted).
D3274 Tes
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E2924-14(2020)(Practice)
Standard Practice for Intumescent Coatings

SIGNIFICANCE AND USE
5.1 This practice is intended for use by material specifiers, general contractors, applicators, or any individual or group requiring information regarding the application of intumescent coatings to provide a fire resistance rating to structural steel.  
5.2 This practice is not intended to replace the manufacturer’s application instructions.
SCOPE
1.1 This practice provides architects, specifiers and building owners various consensus recommendations to specify industry’s best practices for intumescent coatings.  
1.2 This practice covers the best practice for the following:  
1.2.1 The manufacturing, testing, labeling, transportation, delivery, and storage, including shelf life, of intumescent coatings.  
1.2.2 The application of the intumescent coatings to structural steel for the purposes of providing fire resistance.  
1.2.3 The inspection, including safety and equipment, of intumescent coatings during and after the application.  
1.3 Standard Practice—This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title means only that the document has been approved through the ASTM consensus process.  
1.4 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: This practice references fire-test-response standards and may involve hazardous tasks. Therefore, the following caveats are also referenced. This practice references tests used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. This practice references tests used to predict or provide a quantitative measure of the fire hazard from a specified set of fire conditions involving specific materials, products, or assemblies. This assessment does not necessarily predict the hazard of actual fires which involve conditions other than those assumed in the analysis. This practice references tests used to determine certain fire-test responses of materials, products, or assemblies to heat and flame under controlled conditions by using results obtained from fire-test-response standards. The results obtained from using this practice do not, by themselves, constitute measures of fire hazard or fire risk. Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Com...

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D4086-18(2023)(Practice)
Standard Practice for Visual Evaluation of Metamerism

SIGNIFICANCE AND USE
4.1 Metameric color matches result from the use of different colorants (pigments, dyes, and the like) in achieving the same color match. Usually, the purchaser requires that the color match be nonmetameric; this practice permits this requirement to be quickly tested in both field and laboratory. Where nonmetameric matches are not possible or practicable, for cost or other reasons, some limitation of metamerism may be required. The procedures for estimating the magnitude of metamerism described in this practice provide methods for assessing the effectiveness of such limitation.
SCOPE
1.1 This practice describes visual methods for detecting metamerism and for estimating the magnitude of a metameric color difference.  
1.2 The practice is limited to the consideration of illuminant metamerism and observer metamerism. This practice does not cover gonioapparent samples.  
1.3 This practice does not provide for the computation of indices of metamerism based upon instrumental measurement of spectral characteristics.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7190-10(2023)(Practice)
Standard Practice to Evaluate Leaching of Water-Soluble Materials from Latex Paint Films

SIGNIFICANCE AND USE
4.1 Surfactant staining is a common problem with exterior house paints, particularly when subjected to humid environments (such as morning dew) shortly after application.  
4.2 Interior paints used in humid areas such as kitchens and bathrooms may also experience surfactant staining.  
4.3 Leaching of water-soluble materials may be dependent on colorant dispersions that are mixed into tint base paints. Other paint components may also affect the leaching of water-soluble materials.
SCOPE
1.1 This practice covers the ability of a latex paint film to resist staining caused by the leaching of water-soluble materials when contacted with water shortly after application.  
1.2 Water staining is attributed to the leaching of surfactants or other water-soluble materials from a paint film.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4147-18(2023)(Practice)
Standard Practice for Applying Coil Coatings Using Wire-Wound Drawdown Bars

SIGNIFICANCE AND USE
3.1 This practice is useful in the laboratory to simulate roll-coated films.
SCOPE
1.1 This practice covers a procedure for applying a coil coating film of uniform thickness on a flat metal panel using wire-wound drawdown bars.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4214-23(Test Method)
Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films

SIGNIFICANCE AND USE
4.1 The procedures provide a broad range of techniques and photographic references to evaluate chalking of exterior paints.
SCOPE
1.1 These test methods cover the evaluation of the degree of chalking on white or tinted exterior paint films. These test methods describe the procedures recommended for transferring the chalk to a fabric or fingertip, which is then compared to photographic reference standards, or in the case of adhesive tapes, compared to a reflectance table or photographic reference standards, to determine the degree of chalking.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM F3078-15(2023)(Test Method)
Standard Test Method for Identification and Quantification of Lead in Paint and Similar Coating Materials using Energy Dispersive X-ray Fluorescence Spectrometry (EDXRF)

SIGNIFICANCE AND USE
5.1 This test method provides for analysis of Pb in applied paint using measurement times on the order of several minutes. It can be used to determine whether the sample of applied paint has an areal mass of Pb either substantially less than a specification limit, and therefore does not exceed it, or substantially above the specified limit, and therefore exceeds it.  
5.2 If the value obtained with this test method falls close to a specification limit, a more precise test method may be required to positively determine whether Pb content does or does not exceed the specified limit.
SCOPE
1.1 This test method describes an energy dispersive X-ray fluorescence (EDXRF) procedure for determining the areal mass of Pb in mass per unit area in paint and similar coatings on common substrates of toys and consumer products, such as plastic, wood, steel, aluminum, zinc alloys or fabric.  
1.2 This test method is applicable for homogeneous, single layer paint or similar coatings. The method does not apply to metallic coatings.  
1.3 This test method is applicable for a range of Pb mass per unit area from 0.36 μg/cm2 to approximately 10 μg/cm2 for Pb in paint and similar coatings applied on common substrates. The lower limit of this test method is between 0.36 and 0.75 μg/cm2 depending on the nature of the substrate. Based on the results obtained during the interlaboratory study (ASTM Report F40-1004), it is estimated that the applicable range of this method can be extended up to 50 μg/cm2.  
1.4 The values stated in SI units are to be regarded as standard. Values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    15 pages
    English language
    sale 15% off
ASTM
ASTM F2853-10(2023)(Test Method)
Standard Test Method for Determination of Lead in Paint Layers and Similar Coatings or in Substrates and Homogenous Materials by Energy Dispersive X-Ray Fluorescence Spectrometry Using Multiple Monochromatic Excitation Beams

SIGNIFICANCE AND USE
5.1 This test method may be used for quantitative determinations of Pb in painted and unpainted articles such as toys, children’s products, and other consumer products. Typical test time for quantification of Pb in homogenous samples is 1 to 3 min; and typical test time for quantification of Pb in paint is 4 to 8 min.
SCOPE
1.1 This test method uses energy dispersive X-ray fluorescence (EDXRF) spectrometry for detection and quantification of lead (Pb) in paint layers, similar coatings, or substrates and homogenous materials. The following material types were tested in the interlaboratory study for this standard test method: ABS plastic, polyethylene, polypropylene, PVC, glass, zinc alloy, wood, and fabric.  
1.2 This technique may also be commonly referred to as High Definition X-ray Fluorescence (HDXRF) or Multiple Monochromatic Beam EDXRF (MMB-EDXRF).  
1.3 This test method is applicable for the products and materials described in 1.1 for a Pb mass fraction range of 14 to 1200 mg/kg for uncoated samples and 30 to 450 mg/kg for coated samples, as specified in Table 1 and determined by an interlaboratory study using representative samples  
1.4 Ensure that the analysis area of the sample is visually uniform in appearance and at least as large as the X-ray excitation beam at the point of sample excitation.  
1.5 For coating analysis, this test method is limited to paint and similar coatings. Metallic coatings are not covered by this test method.  
1.6 X-ray Nomenclature—This standard names X-ray lines using the IUPAC convention with the Siegbahn convention in parentheses.  
1.7 There are no known ISO equivalent methods to this standard.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4287-00(2023)(Test Method)
Standard Test Method for High-Shear Viscosity Using a Cone/Plate Viscometer

SIGNIFICANCE AND USE
4.1 The viscosity value obtained by this test method gives information about the flow properties of the material under high-shear conditions similar to those encountered during application: brushing (see Test Method D4958), spraying, electrostatic disk, or roll coating.  
4.2 This test method is suitable for all paints and varnishes whether they are Newtonian in behavior or not. However, due to the narrow gap between the stationary and rotary parts of high-shear viscometers, this test method is more reproducible for paints having finer pigment dispersions as determined by Test Method D1210.
SCOPE
1.1 This test method covers the determination of the viscosity of paints, varnishes, and related products at a rate of shear of 12 000 s−1.  
1.2 Paints and varnishes that dry very rapidly may not give reproducible results with this test method. Measurements made at elevated temperatures may also give poor precision due to loss of volatiles and to drying.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D16-23(Terminology)
Standard Terminology for Paint, Related Coatings, Materials, and Applications

SCOPE
1.1 This standard consists of technical terms used in standards under the jurisdiction of ASTM Committee D01 (on Paint and Related Coatings, Materials, and Applications), and of definitions suitable for use in these standards.
Note 1: When any definition in this standards is quoted or published out of the context of this standard, editorially insert the following delimiting statement “for paints and related coatings, materials, and applications” after the dash following the term (in the absence of an existing delimiting statement). This will limit the filed of application of the term and definition to that approved by this committee.  
1.2 In this terminology standard, definitions used in other ASTM standards are indicated by following the definition with the designation of that standard. In some cases, a relevant D01 subcommittee is also listed. Definitions influenced by those used by other organizations are indicated by the acronym of the organization. Primary terms are given in bold, while narrower and unapproved terms are given in italics.  
1.3 There are several specialized terminology standards under the jurisdiction of Committee D01, as follows: D804, D1695, D6440, D6488, and D7188. Few definitions from those standards are included in Terminology D16. Therefore, in searches for definitions of paints and coatings terms, these standards should be included where appropriate.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D6762-18(2023)(Test Method)
Standard Test Method for Determining the Hiding Power of Paint by Visual Evaluation of Spray Applied Coatings

SIGNIFICANCE AND USE
5.1 This test method determines hiding power of a test paint by visual evaluation of a spray applied coating.
Note 1: Test Method D2805 describes an instrumental method for determining hiding power. The paint film is applied at a uniform thickness (for example with a doctor blade), the film thickness is measured rigorously, and the opacity is determined photometrically. Hiding power is thereby determined with a high degree of precision.  
5.2 Test Method D6762 is less precise than Test Method D2805, but is commonly used since it is more closely related to the application characteristics of the paint and is simpler in concept and evaluation.
SCOPE
1.1 This test method provides for the quantitative visual determination of the film thickness required to achieve full hiding. This film thickness is considered to be the hiding power of a test paint.  
1.2 This method applies only to spray applied coatings but its concepts are valid for other methods of application as well.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off