ASTM D7672-14e1
(Specification)Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies
Standard Specification for Evaluating Structural Capacities of Rim Board Products and Assemblies
ABSTRACT
This specification provides procedures for testing and establishing the structural capacities of proprietary rim board products and assemblies for use in light-frame wood construction using I-joist or structural composite lumber joist framing. This specification also establishes several procedures used to test rim board products and assemblies, to judge their acceptability, and to establish allowable design capacities.
SCOPE
1.1 This specification provides procedures for testing and establishing the structural capacities of proprietary rim board products and assemblies for use in light-frame wood construction using I-joist or structural composite lumber joist framing. This specification does not apply to commodity rim board products.
1.2 This specification was developed in light of currently manufactured panel, structural composite lumber, and pre-fabricated I-joist rim board products as defined in 3.2. Materials that do not conform to the definitions of 3.2 are beyond the scope of this specification.
1.3 Fire safety, sound transmission, building envelope performance, and cutting/notching attributes of rim board products and assemblies fall outside the scope of this specification.
1.4 This specification primarily considers end use in dry service conditions, such as most protected framing members, where the equilibrium moisture content for solid-sawn lumber is less than 16 %.
1.5 This specification provides methods to establish “allowable stress” design resistances for use with the National Design Specification for Wood Construction (NDS). Derivation of design resistances from the test data in accordance with “load and resistance factor design” or “limit states design” are beyond the scope of this specification.
1.6 Quality control requirements are outside the scope of this Specification.
1.7 The performance of a rim board product will be affected by the constituent wood species, geometry, adhesive, and production parameters. Therefore, rim board products produced by each individual manufacturer shall be evaluated to determine their product properties, regardless of the similarity in characteristics to products produced by other manufacturers.
1.8 Where a manufacturer produces product in more than one facility, each production facility shall be evaluated independently. For additional production facilities, any revisions to the full qualification program in accordance with this specification shall be approved by an accredited, independent qualifying agency.
1.9 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:D7672 −14
Standard Specification for
Evaluating Structural Capacities of Rim Board Products and
1
Assemblies
This standard is issued under the fixed designation D7672; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Tables 1 and 2 were reformatted in April 2019.
INTRODUCTION
Rimboardassembliesareanengineeredcomponentwithinlight-framewoodplatformconstruction.
Rim board assemblies serve in multiple structural capacities, including: providing floor closure and
diaphragmattachment,transferringverticalandin-planelateralloads,restrictingout-of-planerotation
and lateral translation at the ends of the floor joists, providing deck ledger attachment, and spanning
wall openings as a header material. Rim board products, which serve a principal role as a component
integrated within a rim board assembly, can vary by wood species, size, shape, and type. Rim board
products and assemblies require evaluation of their mechanical properties, physical properties, and
their response to end use environments. Procedures established in this Specification provide a means
to test rim board products and assemblies, to judge their acceptability, and to establish allowable
design capacities.
1. Scope 1.5 Thisspecificationprovidesmethodstoestablish“allow-
ablestress”designresistancesforusewiththeNationalDesign
1.1 This specification provides procedures for testing and
Specification for Wood Construction (NDS). Derivation of
establishing the structural capacities of proprietary rim board
design resistances from the test data in accordance with “load
products and assemblies for use in light-frame wood construc-
and resistance factor design” or “limit states design” are
tion using I-joist or structural composite lumber joist framing.
beyond the scope of this specification.
This specification does not apply to commodity rim board
products. 1.6 Quality control requirements are outside the scope of
this Specification.
1.2 This specification was developed in light of currently
manufactured panel, structural composite lumber, and pre- 1.7 Theperformanceofarimboardproductwillbeaffected
fabricated I-joist rim board products as defined in 3.2. Mate- by the constituent wood species, geometry, adhesive, and
rials that do not conform to the definitions of 3.2 are beyond production parameters. Therefore, rim board products pro-
the scope of this specification. duced by each individual manufacturer shall be evaluated to
determine their product properties, regardless of the similarity
1.3 Fire safety, sound transmission, building envelope
incharacteristicstoproductsproducedbyothermanufacturers.
performance, and cutting/notching attributes of rim board
products and assemblies fall outside the scope of this specifi- 1.8 Where a manufacturer produces product in more than
cation. one facility, each production facility shall be evaluated inde-
pendently. For additional production facilities, any revisions to
1.4 This specification primarily considers end use in dry
the full qualification program in accordance with this specifi-
service conditions, such as most protected framing members,
cation shall be approved by an accredited, independent quali-
where the equilibrium moisture content for solid-sawn lumber
fying agency.
is less than 16%.
1.9 Thevaluesstatedininch-poundunitsaretoberegarded
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
1
This specification is under the jurisdiction ofASTM Committee D07 on Wood
and are not considered standard.
and is the direct responsibility of Subcommittee D07.05 on Wood Assemblies.
Current edition approved Oct. 1, 2014. Published November 2014. Originally
1.10 This standard does not purport to address all of the
approved in 2011. Last previous edition approved in 2013 as D7672–13. DOI:
10.1520/D7672–14E01. safety concerns, if any, associated with its use. It is the
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D7672−14
responsibility of the user of this standard to establish appro- D5055Specification for Establishing and Monitoring Struc-
priate safety and health practices and determine the applica- tural Capacities of Prefabricated Wood I-Joists
bility of regulatory limitations prior to use. D5456Specification for Evaluation of Structural Composite
Lumber Products
1.11 This international standard was developed in accor-
D7033Practice for Establishing Design Capacities for Ori-
dance with internationally rec
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D7672 − 14 D7672 − 14
Standard Specification for
Evaluating Structural Capacities of Rim Board Products and
1
Assemblies
This standard is issued under the fixed designation D7672; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Tables 1 and 2 were reformatted in April 2019.
INTRODUCTION
Rim board assemblies are an engineered component within light-frame wood platform construction.
Rim board assemblies serve in multiple structural capacities, including: providing floor closure and
diaphragm attachment, transferring vertical and in-plane lateral loads, restricting out-of-plane rotation
and lateral translation at the ends of the floor joists, providing deck ledger attachment, and spanning
wall openings as a header material. Rim board products, which serve a principal role as a component
integrated within a rim board assembly, can vary by wood species, size, shape, and type. Rim board
products and assemblies require evaluation of their mechanical properties, physical properties, and
their response to end use environments. Procedures established in this Specification provide a means
to test rim board products and assemblies, to judge their acceptability, and to establish allowable
design capacities.
1. Scope
1.1 This specification provides procedures for testing and establishing the structural capacities of proprietary rim board products
and assemblies for use in light-frame wood construction using I-joist or structural composite lumber joist framing. This
specification does not apply to commodity rim board products.
1.2 This specification was developed in light of currently manufactured panel, structural composite lumber, and pre-fabricated
I-joist rim board products as defined in 3.2. Materials that do not conform to the definitions of 3.2 are beyond the scope of this
specification.
1.3 Fire safety, sound transmission, building envelope performance, and cutting/notching attributes of rim board products and
assemblies fall outside the scope of this specification.
1.4 This specification primarily considers end use in dry service conditions, such as most protected framing members, where
the equilibrium moisture content for solid-sawn lumber is less than 16 %.
1.5 This specification provides methods to establish “allowable stress” design resistances for use with the National Design
Specification for Wood Construction (NDS). Derivation of design resistances from the test data in accordance with “load and
resistance factor design” or “limit states design” are beyond the scope of this specification.
1.6 Quality control requirements are outside the scope of this Specification.
1.7 The performance of a rim board product will be affected by the constituent wood species, geometry, adhesive, and
production parameters. Therefore, rim board products produced by each individual manufacturer shall be evaluated to determine
their product properties, regardless of the similarity in characteristics to products produced by other manufacturers.
1.8 Where a manufacturer produces product in more than one facility, each production facility shall be evaluated independently.
For additional production facilities, any revisions to the full qualification program in accordance with this specification shall be
approved by an accredited, independent qualifying agency.
1
This specification is under the jurisdiction of ASTM Committee D07 on Wood and is the direct responsibility of Subcommittee D07.05 on Wood Assemblies.
Current edition approved Oct. 1, 2014. Published November 2014. Originally approved in 2011. Last previous edition approved in 2013 as D7672–13. DOI:
10.1520/D7672–14.10.1520/D7672–14E01.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
D7672 − 14
1.9 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.