ASTM F1347-91(2001)
(Specification)Standard Specification for Manually Operated Fueling Hose Reels
Standard Specification for Manually Operated Fueling Hose Reels
SCOPE
1.1 This specification covers manually operated fueling hose reels for use with collapsible and noncollapsible hose.
1.2 The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12 of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 1347 – 91 (Reapproved 2001)
Standard Specification for
1
Manually Operated Fueling Hose Reels
This standard is issued under the fixed designation F 1347; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope MIL-STD-130 Identification Marking of U.S. Military
Property
1.1 This specification covers manually operated fueling
hose reels for use with collapsible and noncollapsible hose.
3. Classification
1.2 The values stated in inch-pound units are to be regarded
3.1 Fueling hose reels shall be of one of the following types
as standard. The SI units given in parentheses are for informa-
as specified:
tion only.
1
3.1.1 Type 1—For 150 ft (46 m) of collapsible 2 ⁄2-in.
1.3 The following precautionary caveat pertains only to the
(65-mm) hose.
test methods portion, Section 12 of this specification: This
1
3.1.2 Type 2—For 150 ft (46 m) of noncollapsible 1 ⁄2-in.
standard does not purport to address all of the safety concerns,
(38-mm)hoseor100ft(30m)ofnoncollapsible2-in.(50-mm)
if any, associated with its use. It is the responsibility of the user
hose.
of this standard to establish appropriate safety and health
1
3.1.3 Type 3—For 150 ft (46 m) of noncollapsible 1 ⁄2-in.
practices and determine the applicability of regulatory limita-
1
(38-mm) hose or for 150 ft (46 m) of collapsible 2 ⁄2-in.
tions prior to use.
(65-mm) hose.
2. Referenced Documents 3.1.4 Type 4—Capacity as specified by purchaser.
2.1 ASTM Standards:
4. Ordering Information
2
B148 Specification for Aluminum-Bronze Sand Castings
4.1 Ordersformaterialunderthisspecificationshallinclude
D3006 Specification for Polyethylene Plastic Pressure-
3
the following information:
Sensitive Electrical Insulating Tape
4 4.1.1 Title, number, and year of issue of this specification,
D3951 Practice for Commercial Packaging
5 4.1.2 Type of hose reel including hose size and type (see
2.2 Military Specifications:
3.1), (length of hose for Type 4),
MIL-S-901 Shock Test, H.I. (High-Impact); Shipboard Ma-
4.1.3 Whetherright-orleft-handreelsarerequired(see6.5),
chinery, Equipment and Systems, Requirements for
4.1.4 Flange inlet thickness and bolt hole dimensions (see
MIL-T-16366 Terminals, Electric Lug and Conductor
6.7),
Splices, Crimp Style
4.1.5 Drawings required (see 9.1),
MIL-H-17902 Hose, End Fittings and Hose Assemblies,
4.1.6 Thenumberofsamplestobeinspectedandtested(see
Synthetic Rubber, Aircraft Fuels
11.2),
MIL-F-20042 Flanges, Pipe and Bulkhead, Bronze (Silver
4.1.7 Certification, if required (see 15.1),
Brazing)
4.1.8 Test report, if required (see 15.1), and
MIL-P-24441 Epoxy-Polyamide Primer
5 4.1.9 Applicability of supplementary requirements.
2.3 Military Standard:
5. Materials and Manufacture
5.1 Exceptasotherwisespecifiedherein,thehosereelsshall
1
This specification is under the jurisdiction ofASTM Committee F25 on Ships
be constructed of aluminum, aluminum bronze, or other
and Marine Technology and is the direct responsibility of Subcommittee F25.07 on
suitable nonsparking materials.All fittings conveying aromatic
General Requirements.
fuels through the hose reel shall be made of aluminum bronze
Current edition approved July 15, 1991. Published September 1991.
2
Annual Book of ASTM Standards, Vol 02.01.
in accordance with Specification B148, copper alloy UNS No.
3
Annual Book of ASTM Standards, Vol 10.02.
C95300.Topreventdeteriorationinseaatmosphere,aluminum
4
Annual Book of ASTM Standards, Vol 15.09.
5 parts should not contact brass or bronze; however, where such
Available from Standardization Documents Order Desk, Building 4D, 700
Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS. aluminum parts come in contact with brass or bronze, they
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
F 1347 – 91 (2001)
shall be protected by adhesive-backed insulating tape, Speci- 6.2 Reel Drum—The reel drum may have either smoothly
fication D3006. All aluminum parts shall be given a coat of formed flat sides or suitable spoke ribs, so formed as not to
epoxy-polyamide primer. damage the hose. The rims of the drum shall provide a good
grip for hand rewind.
6. Construction 6.3 Holding Brake—Reels shall be provided with a holding
brake to lock the reel in any position.
6.1 Reel and Drum Assembly—The hose reel shall be of a
6.4 Nozzle Clamp—Thereelshallbefittedwithadevicefor
durable, rigid construction, as light in weight and compac
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.