ASTM F1899-14a
(Specification)Standard Specification for Food Waste Pulper Without Waterpress Assembly
Standard Specification for Food Waste Pulper Without Waterpress Assembly
ABSTRACT
This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service wear. Pulper assemblies shall be of the following types: Type A and Type B. Lubricating points shall be readily accessible, and the pulper shall be lubricated with the proper amount of lubricant prior to delivery. All surfaces of the machine, other than corrosion-resistant materials, shall be protected against corrosion in the use environment and shall present a neat appearance. Test method shall be performed to demonstrate the ability of the unit to meet the capacity requirements and to insure that there is no leakage during operation.
SCOPE
1.1 This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper, and disposable plastic food service ware.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification:
1.4 This standard does not purport to address all of the safety concerns, if, any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1899 −14a An American National Standard
Standard Specification for
1
Food Waste Pulper Without Waterpress Assembly
This standard is issued under the fixed designation F1899; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A505 Specification for Steel, Sheet and Strip, Alloy, Hot-
Rolled and Cold-Rolled, General Requirements for
1.1 This specification covers pulper assemblies intended for
A513 Specification for Electric-Resistance-Welded Carbon
grinding of food scraps and limited amounts of cardboard,
and Alloy Steel Mechanical Tubing
paper, and disposable plastic food service ware.
A519 Specification for Seamless Carbon and Alloy Steel
1.2 The values stated in inch-pound units are to be regarded
Mechanical Tubing
as standard. The values given in parentheses are mathematical
A532/A532M Specification for Abrasion-Resistant Cast
conversions to SI units that are provided for information only
Irons
and are not considered standard.
A554 Specification for Welded Stainless Steel Mechanical
1.3 The following safety hazards caveat pertains only to the
Tubing
test method portion, Section 13, of this specification:
A582/A582M Specification for Free-Machining Stainless
1.4 This standard does not purport to address all of the Steel Bars
safety concerns, if, any, associated with its use. It is the A681 Specification for Tool Steels Alloy
responsibility of the user of this standard to establish appro- B43 Specification for Seamless Red Brass Pipe, Standard
priate safety and health practices and determine the applica-
Sizes
bility of regulatory limitations prior to use.
B75 Specification for Seamless Copper Tube
D2000 Classification System for Rubber Products in Auto-
2. Referenced Documents
motive Applications
2
2.1 ASTM Standards: D2287 Specification for Nonrigid Vinyl Chloride Polymer
A6/A6M Specification for General Requirements for Rolled and Copolymer Molding and Extrusion Compounds
Structural Steel Bars, Plates, Shapes, and Sheet Piling D3915 Specification for Rigid Poly(Vinyl Chloride) (PVC)
A29/A29M SpecificationforGeneralRequirementsforSteel and Chlorinated Poly(Vinyl Chloride) (CPVC) Com-
Bars, Carbon and Alloy, Hot-Wrought
pounds for Plastic Pipe and Fittings Used in Pressure
A53/A53M Specification for Pipe, Steel, Black and Hot-
Applications
Dipped, Zinc-Coated, Welded and Seamless
D3951 Practice for Commercial Packaging
A126 Specification for Gray Iron Castings for Valves,
E674 Specification for Industrial Perforated Plate and
Flanges, and Pipe Fittings
Screens (Round Opening Series)
A240 Specification for Chromium and Chromium-Nickel
F104 Classification System for Nonmetallic Gasket Materi-
Stainless Steel Plate, Sheet, and Strip for Pressure Vessels
als
and for General Applications
F437 Specification for Threaded Chlorinated Poly(Vinyl
A269 Specification for Seamless and Welded Austenitic
Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
Stainless Steel Tubing for General Service
F439 Specification for Chlorinated Poly (Vinyl Chloride)
A276 Specification for Stainless Steel Bars and Shapes
(CPVC) Plastic Pipe Fittings, Schedule 80
A436 Specification for Austenitic Gray Iron Castings
F441/F441M Specification for Chlorinated Poly(Vinyl Chlo-
ride) (CPVC) Plastic Pipe, Schedules 40 and 80
F760 Specification for Food Service Equipment Manuals
1
This specification is under the jurisdiction of ASTM Committee F26 on Food
3
Service Equipment and is the direct responsibility of Subcommittee F26.01 on
2.2 UL Standards:
Cleaning and Sanitation Equipment.
UL 430 Waste Disposers
Current edition approved Nov. 1, 2014. Published December 2014. Originally
UL 508 Industrial Control Equipment
approved in 1998. Last previous edition approved in 2014 as F1899 – 14. DOI:
10.1520/F1899-14A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from Underwriters Laboratories (UL), 333 Pfingsten Rd.,
the ASTM website. Northbrook, IL 60062.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1899−14a
4
2.3 NFPA Standard: defects, which would adversely affect the performance or
NFPA 70 National Electrical Code maintainability of individual components or the overall assem-
5
2.4 ASSE Standard: bly. The unit shall be manufactured for cleanability.
ASSE Standard 1012 Backflow Preventers With Intermedi- 6.1.1 Corrosion-Resistant St
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1899 − 14 F1899 − 14a An American National Standard
Standard Specification for
1
Food Waste Pulper Without Waterpress Assembly
This standard is issued under the fixed designation F1899; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers pulper assemblies intended for grinding of food scraps and limited amounts of cardboard, paper,
and disposable plastic food service ware.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method portion, Section 13, of this specification:
1.4 This standard does not purport to address all of the safety concerns, if, any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling
A29/A29M Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought
A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
A126 Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings
A240 Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for
General Applications
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A276 Specification for Stainless Steel Bars and Shapes
A436 Specification for Austenitic Gray Iron Castings
A505 Specification for Steel, Sheet and Strip, Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
A513 Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
A519 Specification for Seamless Carbon and Alloy Steel Mechanical Tubing
A532/A532M Specification for Abrasion-Resistant Cast Irons
A554 Specification for Welded Stainless Steel Mechanical Tubing
A582/A582M Specification for Free-Machining Stainless Steel Bars
A681 Specification for Tool Steels Alloy
B43 Specification for Seamless Red Brass Pipe, Standard Sizes
B75 Specification for Seamless Copper Tube
D2000 Classification System for Rubber Products in Automotive Applications
D2287 Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds
D3915 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for
Plastic Pipe and Fittings Used in Pressure Applications
D3951 Practice for Commercial Packaging
E674 Specification for Industrial Perforated Plate and Screens (Round Opening Series)
F104 Classification System for Nonmetallic Gasket Materials
1
This specification is under the jurisdiction of ASTM Committee F26 on Food Service Equipment and is the direct responsibility of Subcommittee F26.01 on Cleaning
and Sanitation Equipment.
Current edition approved June 1, 2014Nov. 1, 2014. Published August 2014December 2014. Originally approved in 1998. Last previous edition approved in 20082014
ε1
as F1899 – 98 (2008)F1899 – 14. . DOI: 10.1520/F1899-14.10.1520/F1899-14A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1899 − 14a
F437 Specification for Threaded Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F439 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80
F441/F441M Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80
F760 Specification for Food Service Equipment Manuals
3
2.2 UL Standards:
UL 430 Waste Disposers
UL 508 Industrial Control Equipment
4
2.3 NFPA Standard:
NFPA 70 National Electrical Code
5
2.4 ASSE Stan
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.