ASTM F718-22

Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

ABSTRACT
The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. When filling out the Product/Procedure Data Sheet remember that the information contained therein will be utilized by both technical and production personnel. The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.
SCOPE
1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows:
I. Generic Type and Description
II. Manufacturers Data
III. Properties  
IV. Surface Preparation Minimum Requirements  
The back side of the page contains the following paragraphs:
V. Mixing Procedure
VI. Application  
1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 30-Jun-2022
• ICS: 47.020.05 - Materials and components for shipbuilding
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.01 - Structures

Relations

• Refers: ASTM D93-20 - Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
• Effective Date: 01-Aug-2020

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F718 −22 An American National Standard
Standard Specification for
Shipbuilders and Marine Paints and Coatings Product/
1
Procedure Data Sheet
ThisstandardisissuedunderthefixeddesignationF718;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
3
1.1 The Shipbuilders and Marine Paints and Coatings 2.1 ASTM Standards:
2
Product/Procedure Data Sheet provides on one sheet needed D56 Test Method for Flash Point by Tag Closed Cup Tester
information concerning the characteristics of a specific paint or D93 Test Methods for Flash Point by Pensky-Martens
coating to include generic description, physical properties, Closed Cup Tester
surface preparation requirements, application requirements, D523 Test Method for Specular Gloss
and safety. The front side of the sheet contains four major, D1475 Test Method for Density of Liquid Coatings, Inks,
numbered paragraphs and a highlighted section for Special and Related Products
Safety Precautions. These paragraphs are as follows: D1640 Test Methods for Drying, Curing, or Film Formation
I. Generic Type and Description of Organic Coatings
II. Manufacturers Data D2697 Test Method for Volume Nonvolatile Matter in Clear
III. Properties or Pigmented Coatings
IV. Surface Preparation Minimum Requirements D3278 Test Methods for Flash Point of Liquids by Small
The back side of the page contains the following paragraphs: Scale Closed-Cup Apparatus
V. Mixing Procedure
2.2 ASTM Adjunct:
VI. Application
Shipbuilder’s and Marine Paints and Coatings Product/
2
Procedure Data Sheets
1.2 The completed data sheets can be used by technical
4
personnel to help evaluate the technical acceptability of a
2.3 U.S. EPA Method:
proposed material, by production personnel to evaluate pro-
24 U.S. Environmental Protection Agency, 40 CFR Ch. 1,
duction compatibility of proposed materials and to provide
Part 60, Appendix A, Determination of Volatile Matter
application instructions for selected paints and coatings
Content, Density, Volume Solids, and Weight Solids of
materials, and by quality control personnel to verify attributes
Surface Coatings
of materials.
3. Instructions for Completing Data Sheet
1.3 This international standard was developed in accor-
dance with internationally recognized principles on standard-
3.1 When filling out the Product/Procedure Data Sheet (see
ization established in the Decision on Principles for the
Figs. 1 and 2) remember that the information contained therein
Development of International Standards, Guides and Recom-
will be utilized by both technical and production personnel.
mendations issued by the World Trade Organization Technical
Keep it simple and brief but complete. The following instruc-
Barriers to Trade (TBT) Committee.
tions are organized by paragraph numbers contained within the
data sheet.
1
This standard is under the jurisdiction of ASTM Committee F25 on Ships and
3
Marine Technology and is the direct responsibility of Subcommittee F25.01 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Structures. contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Current edition approved July 1, 2022. Published July 2022. Originally approved Standards volume information, refer to the standard’s Document Summary page on
in 1981. Last previous edition approved in 2017 as F718 – 07 (2017). DOI: the ASTM website.
4
10.1520/F0718-22. Available from U.S. Government Printing Office, Superintendent of
2
Available from ASTM International Headquarters. Order Adjunct No. Documents, 732 N. Capitol St., NW, Washington, DC 20401-0001, http://
ADJF0718. Original adjunct produced in 1993. www.access.gpo.gov.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F718 − 22
FIG. 1 Data Sheet (Front)
2

---------------------- Page: 2 ----------------------
F718 − 22
FIG. 2 Data Sheet (Back)
3

---------------------- Page: 3 ----------------------
F718 − 22
3.2 ParagraphI—GenericTypeandDescription—Useonly 3.6 SpecialSafetyPrecautions—This section should contain
known and industry-accepted generic descriptions. Also, list specific instructions of what to do in the event of skin or eye
anyspecificationspecificterminology(forexample,MIL-PRF- contact or a
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F718 − 07 (Reapproved 2017) F718 − 22 An American National Standard
Standard Specification for
Shipbuilders and Marine Paints and Coatings Product/
1
Procedure Data Sheet
This standard is issued under the fixed designation F718; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
2
1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet provides on one sheet needed information
concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation
requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a
highlighted section for Special Safety Precautions. These paragraphs are as follows:
I. Generic Type and Description
II. Manufacturers Data
III. Properties
IV. Surface Preparation Minimum Requirements
The back side of the page contains the following paragraphs:
V. Mixing Procedure
VI. Application
1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed
material, by production personnel to evaluate production compatibility of proposed materials and to provide application
instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D56 Test Method for Flash Point by Tag Closed Cup Tester
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D523 Test Method for Specular Gloss
D1475 Test Method for Density of Liquid Coatings, Inks, and Related Products
D1640 Test Methods for Drying, Curing, or Film Formation of Organic Coatings
4
D1650 Test Methods for Sampling and Testing Shellac Varnish (Withdrawn 1997)
1
This standard is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.01 on Structures.
Current edition approved May 1, 2017July 1, 2022. Published June 2017July 2022. Originally approved in 1981. Last previous edition approved in 20112017 as F718 – 07
ɛ1
(2011)(2017). . DOI: 10.1520/F0718-07R17.10.1520/F0718-22.
2
Available from ASTM International Headquarters. Order Adjunct No. ADJF0718. Original adjunct produced in 1993.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F718 − 22
D2697 Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
D3278 Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
2.2 ASTM Adjunct:
2
Shipbuilder’s and Marine Paints and Coatings Product/Procedure Data Sheets
4
2.3 U.S. EPA Method:
24 U.S. Environmental Protection Agency, 40 CFR Ch. 1, Part 60, Appendix A, Determination of Volatile Matter Content,
Density, Volume Solids, and Weight Solids of Surface Coatings
3. Instructions for Completing Data Sheet
3.1 When filling out the Product/Procedure Data Sheet (see Figs. 1 and 2) remember that the information contained therein will
be utilized by both technical and production personnel. Keep it simple and brief but complete. The following instructions are
organized by paragraph numbers contained within the data sheet.
3.2 Paragraph I—Generic Type and Description —Use only known and industry-accepted generic descriptions. Also, list any
specification specific terminology (for example, MIL-PRF-23236 Type I, Class 2, etc.). See Fig. 1.
3.3 Paragraph II—Manufacturers Data—This section is self-explanatory with the possible exception of subparagraph (f). This can
be a
...