ASTM D4306-13
(Practice)Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
Standard Practice for Aviation Fuel Sample Containers for Tests Affected by Trace Contamination
SIGNIFICANCE AND USE
3.1 General descriptions for the manual sampling of petroleum products are given in Practice D4057. However, a number of aviation fuel properties are established or affected by trace levels of polar or other compounds. Measurement significance therefore requires that the sample containers not add or adsorb any materials. This practice presents types and preparations of sampling containers found satisfactory for the determination of water separation, copper corrosion, electrical conductivity, thermal stability, lubricity, and trace metal content. An approval procedure for new containers is also given.
3.2 Two properties, particulate contamination and free water content, involve materials easily removed by any sampling container. These properties should be determined by placing the sample directly into the measuring apparatus and not using containers to transport the sample to the measuring equipment.
3.3 Recommendations in this practice provide guidance for immediate use and for storage of samples. Immediate use involves sample storage for periods less than 24 h.
SCOPE
1.1 This practice2 covers the types of and preparation of containers found most suitable for the handling of aviation fuel samples for the determination of critical properties affected by trace contamination.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 5.1, 5.2, 5.3, 5.4, and 5.6.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D4306 − 13 AnAmerican National Standard
Standard Practice for
Aviation Fuel Sample Containers for Tests Affected by Trace
1
Contamination
This standard is issued under the fixed designation D4306; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
4
1. Scope* 2.2 SAE Standard:
2 MAP1794 Aircraft Recommended Practice, Ball-On-
1.1 This practice covers the types of and preparation of
Cylinder (Boc) Aircraft Turbine Fuel Lubricity Tester
containers found most suitable for the handling of aviation fuel
samples for the determination of critical properties affected by
3. Significance and Use
trace contamination.
3.1 General descriptions for the manual sampling of petro-
1.2 The values stated in SI units are to be regarded as
leum products are given in Practice D4057. However, a
standard. No other units of measurement are included in this
number of aviation fuel properties are established or affected
standard.
by trace levels of polar or other compounds. Measurement
1.3 This standard does not purport to address all of the significance therefore requires that the sample containers not
safety concerns, if any, associated with its use. It is the
add or adsorb any materials. This practice presents types and
responsibility of the user of this standard to establish appro- preparations of sampling containers found satisfactory for the
priate safety and health practices and determine the applica-
determination of water separation, copper corrosion, electrical
bility of regulatory limitations prior to use. For specific conductivity, thermal stability, lubricity, and trace metal con-
warning statements, see 5.1, 5.2, 5.3, 5.4, and 5.6.
tent. An approval procedure for new containers is also given.
3.2 Twoproperties,particulatecontaminationandfreewater
2. Referenced Documents
content, involve materials easily removed by any sampling
3
2.1 ASTM Standards:
container. These properties should be determined by placing
D2624 Test Methods for Electrical Conductivity ofAviation
the sample directly into the measuring apparatus and not using
and Distillate Fuels
containers to transport the sample to the measuring equipment.
D3948 TestMethodforDeterminingWaterSeparationChar-
3.3 Recommendations in this practice provide guidance for
acteristicsofAviationTurbineFuelsbyPortableSeparom-
immediate use and for storage of samples. Immediate use
eter
involves sample storage for periods less than 24 h.
D4057 Practice for Manual Sampling of Petroleum and
Petroleum Products
4. Apparatus
D4308 Test Method for Electrical Conductivity of Liquid
4.1 Sampling Containers:
Hydrocarbons by Precision Meter
4.1.1 Epoxy-Coated Containers:
D5452 Test Method for Particulate Contamination in Avia-
4.1.1.1 While generally superior to other coatings, certain
tion Fuels by Laboratory Filtration
epoxy-coatings evolve plasticizers which can adversely affect
critical fuel properties. Because no specification is known to
1
This practice is under the jurisdiction of ASTM Committee D02 on Petroleum
describe a satisfactory epoxy-coating, 6.2 lists an approval
Products and Lubricants and is the direct responsibility of Subcommittee D02.J0.04
procedure which can be used to identify a satisfactory coating.
on Additives and Electrical Properties.
4.1.1.2 For initial qualification of new container sources,
Current edition approved June 15, 2013. Published July 2013. Originally
approved in 1984. Last previous edition approved 2012 as D4306 – 12c. DOI:
coated cans should be examined closely to assure that the
10.1520/D4306-13.
coating covers all inside surfaces. If not, the cans should be
2
The detailed data on which this practice is based may be found in SAE Practice
considered the same as tin-plated, soldered side seam cans.
MAP1794 and three research reports. Supporting data have been filed at ASTM
4.1.1.3 Epoxy-coated cans are generally considered satis-
International Headquarters and may be obtained by requesting Research Reports
RR:D02-1169, RR:D02-1142, and RR:D02-1504.
factory for sampling aviation gasoline.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4306 − 12c D4306 − 13 An American National Standard
Standard Practice for
Aviation Fuel Sample Containers for Tests Affected by Trace
1
Contamination
This standard is issued under the fixed designation D4306; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This practice covers the types of and preparation of containers found most suitable for the handling of aviation fuel samples
for the determination of critical properties affected by trace contamination.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. For specific warning statements, see 5.1, 5.2, 5.3, 5.4, and 5.6.
2. Referenced Documents
3
2.1 ASTM Standards:
D2624 Test Methods for Electrical Conductivity of Aviation and Distillate Fuels
D3948 Test Method for Determining Water Separation Characteristics of Aviation Turbine Fuels by Portable Separometer
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4308 Test Method for Electrical Conductivity of Liquid Hydrocarbons by Precision Meter
D5452 Test Method for Particulate Contamination in Aviation Fuels by Laboratory Filtration
4
2.2 SAE Standard:
MAP1794 Aircraft Recommended Practice, Ball-On-Cylinder (Boc) Aircraft Turbine Fuel Lubricity Tester
3. Significance and Use
3.1 General descriptions for the manual sampling of petroleum products are given in Practice D4057. However, a number of
aviation fuel properties are established or affected by trace levels of polar or other compounds. Measurement significance therefore
requires that the sample containers not add or adsorb any materials. This practice presents types and preparations of sampling
containers found satisfactory for the determination of water separation, copper corrosion, electrical conductivity, thermal stability,
lubricity, and trace metal content. An approval procedure for new containers is also given.
3.2 Two properties, particulate contamination and free water content, involve materials easily removed by any sampling
container. These properties should be determined by placing the sample directly into the measuring apparatus and not using
containers to transport the sample to the measuring equipment.
3.3 Recommendations in this practice provide guidance for immediate use and for storage of samples. Immediate use involves
sample storage for periods less than 24 h.
4. Apparatus
4.1 Sampling Containers:
4.1.1 Epoxy-Coated Containers:
1
This practice is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.J0.04 on
Additives and Electrical Properties.
Current edition approved Dec. 1, 2012June 15, 2013. Published February 2013July 2013. Originally approved in 1984. Last previous edition approved 2012 as
D4306D4306 – 12c.–12b. DOI: 10.1520/D4306-12C.10.1520/D4306-13.
2
The detailed data on which this practice is based may be found in SAE Practice MAP1794 and three research reports. Supporting data have been filed at ASTM
International Headquarters and may be obtained by requesting Research Reports RR:D02-1169, RR:D02-1142, and RR:D02-1504.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D4306 − 13
4.1.1.1 While generally superior to other coatings, certain epoxy-coatings evolve plasticizers which can adversely affect critical
fuel properties. Be
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.