Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

ABSTRACT
This specification covers the general requirements and corresponding test methods for non-pressure (gravity flow) polyethylene (PE) pipes and fittings having interior liner with annular corrugated exterior wall profile, and whose inside diameters are 2 to 60 in. [50 to 1500 mm]. These pipes and fittings are suitable for underground use in subsurface and land drainage systems, which do not operate under surcharge pressure heads. Material requirements are specified for pipe and blow molded fittings, rotationally molded fittings and couplings, injection molded fittings and couplings, and rework materials. The resulting products shall be tested as appropriate, and shall conform to specified requirements for workmanship, dimension (inside diameter, length, minimum inner liner thickness, and perforations), stiffness, flattening resistance, impact resistance, and slow crack growth resistance of PE plastics without pigment.
SCOPE
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings with an interior liner. The inside diameters covered are 2 to 60 in. [50 to 1500 mm].
1.2 The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings suitable for underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.
Note 1—Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based on diameter limitations within the respective standards.
Note 2—Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer applications.
1.3 This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).
1.4 This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.
1.5 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

General Information

Status
Historical
Publication Date
31-Jul-2011
Technical Committee
Drafting Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM F2648/F2648M-11 - Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM F2648/F2648M-11 - Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2648/F2648M −11 AnAmerican National Standard
Standard Specification for
2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile
Wall Polyethylene (PE) Pipe and Fittings for Land Drainage
1
Applications
ThisstandardisissuedunderthefixeddesignationF2648/F2648M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
1.1 This specification covers requirements and test methods
for annular corrugated profile wall polyethylene pipe and
2. Referenced Documents
fittings with an interior liner. The inside diameters covered are
2
2.1 ASTM Standards:
2 to 60 in. [50 to 1500 mm].
D618Practice for Conditioning Plastics for Testing
1.2 The requirements of this specification are intended to
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
provide non-pressure (gravity flow) pipe and fittings suitable
tics
for underground use for subsurface and land drainage systems,
D2122Test Method for Determining Dimensions of Ther-
which do not operate under surcharge pressure heads.
moplastic Pipe and Fittings
NOTE 1—Pipe and fittings produced in accordance with this specifica-
D2321PracticeforUndergroundInstallationofThermoplas-
tion are be installed in compliance with Practice D2321 or Practice F449
tic Pipe for Sewers and Other Gravity-Flow Applications
based on diameter limitations within the respective standards.
D2412Test Method for Determination of External Loading
NOTE 2—Subsurface and land drainage systems pertain principally to
Characteristics of Plastic Pipe by Parallel-Plate Loading
non-municipal or private facilities for water table control, storm drainage
D2444Test Method for Determination of the Impact Resis-
and agricultural drainage applications. The products supplied under this
specification are not intended for any sanitary sewer or municipal storm
tance of Thermoplastic Pipe and Fittings by Means of a
sewer applications.
Tup (Falling Weight)
1.3 This specification covers pipe and fittings with an D3350Specification for Polyethylene Plastics Pipe and Fit-
interior liner using an annular exterior corrugated profile (Fig.
tings Materials
1). D4218Test Method for Determination of Carbon Black
Content in Polyethylene Compounds By the Muffle-
1.4 This specification permits the use of recycled materials
Furnace Technique
for pipe in accordance with the requirements in Section 5.
D5630Test Method for Ash Content in Plastics
1.5 Units—The values stated in either inch-pound units or
D7209Guide for Waste Reduction, Resource Recovery, and
SI units are to be regarded separately as standard. The values
Use of Recycled Polymeric Materials and Products
stated in each system may not be exact equivalents: therefore,
D7399Test Method for Determination of the Amount of
each system shall be used independently of the other. Combin-
Polypropylene(PP)inPolypropylene/LDPEMixturesUs-
ing values from the two systems may result in non-
ing Infrared Spectrophotometer (FTIR)
conformance with the standard.
F412Terminology Relating to Plastic Piping Systems
1.6 This standard does not purport to address all of the
F449Practice for Subsurface Installation of Corrugated
safety concerns, if any, associated with its use. It is the
Polyethylene Pipe for Agricultural Drainage or Water
responsibility of the user of this standard to establish appro-
Table Control
F2136Test Method for Notched, Constant Ligament-Stress
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
Piping Systems and is the direct responsibility of Subcommittee F17.65 on Land
2
Drainage. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Aug. 1, 2011. Published August 2011. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2007. Last previous edition approved in 2010 as F2648/F2648M-10. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/F2648_F2648M-11. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2648/F2648M−11
FIG. 1Annular Corrugated Profile Wall Polyethylene Pipe with Interior Liner
TABLE 1 Pipe Stiffness and Pipe Dimensions
A
Pipe Inside Diameter Minimum Pipe Stiffness at 5% Deflection Minimum Inner Liner Thickness
inch [mm] lb/in/in [kPa] Inch [mm]
2 [50] 50 [345] 0.020 [0.5]
3 [75] 50 [345] 0.020 [0.5]
4
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
An American National Standard
Designation:F2648/F2648M–10 Designation: F2648/F2648M – 11
Standard Specification for
2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile
Wall Polyethylene (PE) Pipe and Fittings for Land Drainage
1
Applications
ThisstandardisissuedunderthefixeddesignationF2648/F2648M;thenumberimmediatelyfollowingthedesignationindicatestheyear
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers requirements and test methods for annular corrugated profile wall polyethylene pipe and fittings
with an interior liner. The inside diameters covered are 2 to 60 in. [50 to 1500 mm].
1.2 The requirements of this specification are intended to provide non-pressure (gravity flow) pipe and fittings suitable for
underground use for subsurface and land drainage systems, which do not operate under surcharge pressure heads.
NOTE 1—Pipe and fittings produced in accordance with this specification are be installed in compliance with Practice D2321 or Practice F449 based
on diameter limitations within the respective standards.
NOTE 2—Subsurface and land drainage systems pertain principally to non-municipal or private facilities for water table control, storm drainage and
agricultural drainage applications. The products supplied under this specification are not intended for any sanitary sewer or municipal storm sewer
applications.
1.3 This specification covers pipe and fittings with an interior liner using an annular exterior corrugated profile (Fig. 1).
1.4 This specification permits the use of recycled materials for pipe in accordance with the requirements in Section 5.
1.5 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated
in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D618 Practice for Conditioning Plastics for Testing
D1600 Terminology for Abbreviated Terms Relating to Plastics
D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications
D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading
D2444 Test Method for Determination of the Impact Resistance ofThermoplastic Pipe and Fittings by Means of aTup (Falling
Weight)
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D4218 TestMethodforDeterminationofCarbonBlackContentinPolyethyleneCompoundsBytheMuffle-FurnaceTechnique
D5630 Test Method for Ash Content in Plastics
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
D7399 Test Method for Determination of theAmount of Polypropylene (PP) in Polypropylene/LDPE Mixtures Using Infrared
Spectrophotometer (FTIR)
F412 Terminology Relating to Plastic Piping Systems
F449 Practice for Subsurface Installation of Corrugated Polyethylene Pipe for Agricultural Drainage or Water Table Control
F2136 Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of
HDPE Resins or HDPE Corrugated Pipe
1
ThisspecificationisunderthejurisdictionofASTMCommitteeF17onPlasticPipingSystemsandisthedirectresponsibilityofSubcommitteeF17.65onLandDrainage.
Current edition approved Dec.Aug. 1, 2010.2011. Published JanuaryAugust 2011. Originally approved in 2007. Last previous edition approved in 20072010 as
F2648/F2648M-107. DOI: 10.1520/F2648_F2648M-101.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.