ASTM C930-18
(Classification)Standard Classification of Potential Health and Safety Concerns Associated With Thermal Insulation Materials and Accessories
Standard Classification of Potential Health and Safety Concerns Associated With Thermal Insulation Materials and Accessories
SIGNIFICANCE AND USE
4.1 The purpose of this classification is to identify potential concerns and effects which may occur during the life cycle (installation, service, removal, and disposal) of insulation materials and accessories resulting from direct contact or indirect action or events.
4.2 This classification does not identify remedial or preventive steps that may be taken to correct potential problems or hazards; rather it is intended as a checklist that will make it easier to deal constructively with these potentials, and to determine what, if any, specific requirements need to be added to other standards concerning insulation materials or accessories. (See Appendix X2 for sources of information.)
4.3 This classification recognizes that proper handling and installation procedures can substantially reduce the potential concerns and effects. Further, it recognizes that in some situations the presence or creation of potential effects or hazards results from an intervening act of human or natural origin, or depends on access to or contact with the materials or accessories. Lack of compatibility of the individual components of an insulation system with each other or the environmental conditions within which the system will operate, or both, may create unanticipated effects. (See Appendix X3.)
SCOPE
1.1 This classification identifies potential concerns and effects that could result from direct contact with thermal insulation materials and accessories, or be caused by indirect action of events such as aging, fire, or physical disturbance.
1.2 Intent of Classification:
1.2.1 It is the intent of this classification to alert others to potential concerns, effects, hazards, or risk.
1.2.2 It is not the intent of this classification to establish the degree of risk or hazard or limiting values of potential hazards.
1.2.3 It is not the intent of this classification to establish or recommend methods or markings to reduce or mitigate the potential; however, it is recognized that correct procedures and precautionary measures can substantially reduce or eliminate some of the potential concerns, effects, hazards, or risks.
Note 1: See Appendix X1 for commentary.
1.3 This classification recognizes the responsibility of producers and users, as appropriate, to: (1) provide information on known effects or hazards, (2) advise on established safety and health practices, and (3) determine applicable regulatory requirements.
1.4 This classification does not address the health and safety concerns of thermal insulation materials and accessories during manufacture.
1.5 Omission of an item from this classification does not imply an absence of potential concerns or effects.
1.6 There is no importance in the order of listing.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C930 −18
Standard Classification of
Potential Health and Safety Concerns Associated With
1
Thermal Insulation Materials and Accessories
This standard is issued under the fixed designation C930; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2. Referenced Documents
2
1.1 This classification identifies potential concerns and ef-
2.1 ASTM Standards
fects that could result from direct contact with thermal insula-
C1055 Guide for Heated System Surface Conditions that
tion materials and accessories, or be caused by indirect action
Produce Contact Burn Injuries
of events such as aging, fire, or physical disturbance.
3. Terminology
1.2 Intent of Classification:
3.1 Definitions of Terms Specific to This Standard:
1.2.1 It is the intent of this classification to alert others to
potential concerns, effects, hazards, or risk. 3.1.1 degree of risk—the probability or expected frequency
of the event, multiplied by the expected magnitude of exposure
1.2.2 It is not the intent of this classification to establish the
degree of risk or hazard or limiting values of potential hazards. and the potential for harm.
1.2.3 It is not the intent of this classification to establish or
3.1.2 direct contact—the straightforward touching resulting
recommend methods or markings to reduce or mitigate the
from use, manipulation, placement, etc.
potential; however, it is recognized that correct procedures and
3.1.3 hazard—a condition or set of circumstances that
precautionary measures can substantially reduce or eliminate
presents a specific injury or adverse health potential.
some of the potential concerns, effects, hazards, or risks.
3.1.4 indirect action or events—the actions or events that
NOTE 1—See Appendix X1 for commentary.
are not directly created by, or straightforwardly caused by, the
1.3 This classification recognizes the responsibility of pro- person(s) potentially exposed to the effects or hazards.
ducers and users, as appropriate, to: (1) provide information on
3.1.5 potential—the possible as opposed to the actual; that
known effects or hazards, (2) advise on established safety and
which may, but has not yet, come into being; that which is
health practices, and (3) determine applicable regulatory re-
latent, unrealized.
quirements.
3.1.6 risk—the exposure to chance of injury or illness or
1.4 Thisclassificationdoesnotaddressthehealthandsafety
loss.
concernsofthermalinsulationmaterialsandaccessoriesduring
3.1.6.1 Discussion—Riskisacombinationofhazardandthe
manufacture.
probability of harm.
1.5 Omission of an item from this classification does not
4. Significance and Use
imply an absence of potential concerns or effects.
4.1 The purpose of this classification is to identify potential
1.6 There is no importance in the order of listing.
concerns and effects which may occur during the life cycle
1.7 This international standard was developed in accor-
(installation, service, removal, and disposal) of insulation
dance with internationally recognized principles on standard-
materials and accessories resulting from direct contact or
ization established in the Decision on Principles for the
indirect action or events.
Development of International Standards, Guides and Recom-
4.2 This classification does not identify remedial or preven-
mendations issued by the World Trade Organization Technical
tive steps that may be taken to correct potential problems or
Barriers to Trade (TBT) Committee.
hazards; rather it is intended as a checklist that will make it
1
This classification is under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on
2
Insulation Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Feb. 1, 2018. Published February 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1980. Last previous edition approved in 2012 as C930 – 12. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0930-18. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C930−18
easier to deal constructively with these potentials, and to 5.2.1.1 A Safety Data Sheet (SDS) is required by the
determine what, if any, specific requirements need to be added Occupational Safety and Health Administration (OSHA), U.S.
to o
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C930 − 12 C930 − 18
Standard Classification of
Potential Health and Safety Concerns Associated With
1
Thermal Insulation Materials and Accessories
This standard is issued under the fixed designation C930; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This classification identifies potential concerns and effects that could result from direct contact with thermal insulation
materials and accessories, or be caused by indirect action of events such as aging, fire, or physical disturbance.
1.2 Intent of Classification:
1.2.1 It is the intent of this classification to alert others to potential concerns, effects, hazards, or risk.
1.2.2 It is not the intent of this classification to establish the degree of risk or hazard or limiting values of potential hazards.
1.2.3 It is not the intent of this classification to establish or recommend methods or markings to reduce or mitigate the potential;
however, it is recognized that correct procedures and precautionary measures can substantially reduce or eliminate some of the
potential concerns, effects, hazards, or risks.
NOTE 1—See Appendix X1 for commentary.
1.3 This classification recognizes the responsibility of producers and users, as appropriate, to: (1) provide information on known
effects or hazards, (2) advise on established safety and health practices, and (3) determine applicable regulatory requirements.
1.4 This classification does not address the health and safety concerns of thermal insulation materials and accessories during
manufacture.
1.5 Omission of an item from this classification does not imply an absence of potential concerns or effects.
1.6 There is no importance in the order of listing.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards
C1055 Guide for Heated System Surface Conditions that Produce Contact Burn Injuries
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 degree of risk—the probability or expected frequency of the event, multiplied by the expected magnitude of exposure and
the potential for harm.
3.1.2 direct contact—the straightforward touching resulting from use, manipulation, placement, etc.
3.1.3 hazard—a condition or set of circumstances that presents a specific injury or adverse health potential.
3.1.4 indirect action or events—the actions or events that are not directly created by, or straightforwardly caused by, the
person(s) potentially exposed to the effects or hazards.
1
This classification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
Systems.
Current edition approved Sept. 1, 2012Feb. 1, 2018. Published October 2012February 2018. Originally approved in 1980. Last previous edition approved in 20052012
as C930 – 05.C930 – 12. DOI: 10.1520/C0930-12.10.1520/C0930-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C930 − 18
3.1.5 potential—the possible as opposed to the actual; that which may, but has not yet, come into being; that which is latent,
unrealized.
3.1.6 risk—the exposure to chance of injury or illness or loss.
3.1.6.1 Discussion—
Risk is a combination of hazard and the probability of harm.
4. Significance and Use
4.1 The purpose of this classification is to identify potential concerns and effects which may occur during the life cycle
(installation, service, removal, and disposal) of insulation materials and accessories resulting from direct contact or indirect action
or events.
4.2 This classification does not identify remedial or preventive ste
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.