ASTM F2162-01e2

Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type

SCOPE
1.1 This specification covers standard-type needle roller bearings having drawn outer rings, full complement, without inner rings, with either open or closed ends.
1.2 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged.
1.3 The inner rings specified in this specification are not intended for use in flight critical systems of aircraft.
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.
Note 1—This specification was originally developed by the Department of Defense and maintained by the Defense Supply Center Richmond. It is intended to replicate the requirements of MS 17130.

General Information

• Status: Historical
• Publication Date: 11-Dec-2001
• ICS: 21.100.20 - Rolling bearings
• Technical Committee: F34 - Rolling Element Bearings
• Drafting Committee: F34.04 - Automotive/Industrial Bearing

Relations

• Replaces: ASTM F2162-01e1 - Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type
• Effective Date: 12-Dec-2001
• Replaced By: ASTM F2162-01(2008) - Standard Specification for Bearing, Roller, Needle: Drawn Outer Ring, Full Complement, Without Inner Ring, Open and Closed End, Standard Type
• Effective Date: 01-May-2008
• Referred By: ASTM F2163-01(2016) - Standard Specification for Ring, Bearing, Inner: for Needle Roller Bearing With Drawn Outer Ring
• Effective Date: 12-Dec-2001
• Referred By: ASTM F2431-04(2018) - Standard Specification for Ring Bearing, Inner: For Needle Roller Bearing with Thick Outer Ring
• Effective Date: 12-Dec-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
e2
Designation: F 2162 – 01
Standard Specification for
Bearing, Roller, Needle: Drawn Outer Ring, Full
Complement, Without Inner Ring, Open and Closed End,
1
Standard Type
This standard is issued under the fixed designation F 2162; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Note 1 was changed editorially in June 2002.
2
e NOTE—Table 1 was editorially corrected in May 2003.
1. Scope ASME B 46.1 Surface Texture Surface Roughness, Wavi-
3
ness, and Lay
1.1 This specification covers standard-type needle roller
2.3 SAE Standard:
bearings having drawn outer rings, full complement, without
4
SAE J-404 Chemical Composition of SAE Alloy Steels
inner rings, with either open or closed ends.
2.4 Military Standard:
1.2 Theuseofrecycledmaterialsthatmeettherequirements
MIL-STD-130 Identification Marking of US Military Prop-
of the applicable material specification without jeopardizing
5
erty
the intended use of the item is encouraged.
2.5 American Bearing Manufacturer’s Association (ABMA)
1.3 The inner rings specified in this specification are not
Standard:
intended for use in flight critical systems of aircraft.
STD 4 Tolerance Definitions and Gauging Practices For
1.4 The values stated in inch-pound units are to be regarded
6
Ball and Roller Bearings
as the standard. The values given in parentheses are provided
2.6 ISO Standards:
for information only.
7
ISO 5593 Rolling Bearings—Vocabulary
7
NOTE 1—This specification contains many of the requirements of
ISO 1132 Rolling Bearings—Tolerances—Definitions
MS17131, which was originally developed by the Department of Defense
and is currently maintained by the Defense Supply Center Richmond.
3. Terminology
3.1 Definitions—For definitions of terms used in this speci-
2. Referenced Documents
fication, refer to ABMA STD 4 Tolerance Definitions and
2
2.1 ASTM Standards:
Gauging Practices for Ball and Roller Bearings, ISO 1132
E18 Test Methods for Rockwell Hardness and Rockwell
Roller Bearings—Tolerances—Definitions, and to ISO 5593
Superficial Hardness of Metallic Materials
Rolling Bearings—Vocabulary
E 140 Standard Hardness Conversion Tables for Metals
3.2 Definitions of Terms Specific to This Standard:
(Relationship Among Brinell Hardness, Vickers Hardness,
3.2.1 average life (L ), n—for a radial roller bearing, the
50
Rockwell Hardness, Rockwell Superficial Hardness,
number of revolutions that 50 % of a group of bearings will
Knoop Hardness, and Scleroscope Hardness)
complete or exceed before the first evidence of fatigue devel-
E 384 Test Method for Microindentation Hardness
ops.
F 2163 Specification for Ring, Bearing, Inner: for Needle
Roller Bearing With Drawn Outer Ring
2.2 ASME Standard:
3
Available from Global Engineering Documents, 15 Inverness Way, East
Englewood, CO 80112.
1 4
ThisspecificationisunderthejurisdictionofASTMCommitteeF34onRolling Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Element Bearings and is the direct responsibility of Subcommittee F34.04 on Dr., Warrendale, PA 15096-0001.
5
Automotive/Industrial Bearing. Available from USAInformation Systems, 1092 Laskin Rd., Ste. 208, Virginia
Current edition approved Dec. 12, 2001. Published March 2002. Beach, VA 23451.
2 6
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from the American Bearing Manufacturer’s Association, 1200 19th
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM St. NW, Ste. 300, Washington, DC 20036–2401.
7
Standards volume information, refer to the standard’s Document Summary page on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
e2
F2162–01
3.2.1.1 Discussion—Theaveragelifemaybeasmuchasfive 5.1.3 Dash number (see Table 1),
times the rating life. 5.1.4 Dimensions of roller bearings, including:
3.2.2 basic dynamic load rating (C ), n—for a radial roller 5.1.4.1 Bore diameter, in;
r
bearing, that calculated, constant radial load that a group of 5.1.4.2 Ring gage diameter, in;
apparently identical bearings with stationary outer rings can 5.1.4.3 Width, in; and
theoretically endure for a rating life of one million revolutions 5.1.4.4 Shaft diameter, in;
of the inner ring. 5.1.5 Load rating, including basic static load rating, lb and
3.2.2.1 Discussion—Since applied loading as grea
...