ASTM F1334-14

Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners

SIGNIFICANCE AND USE
4.1 The test results enable the comparison of A-weighted sound emission from vacuum cleaners or hard-floor machines when tested under the condition of this test method.
SCOPE
1.1 This test method calculates the overall A-weighted sound power level emitted by small portable upright, canister, combination vacuum cleaners, backpack vacuum cleaners, hard-floor machines, and central vacuum cleaner motorized nozzles intended for operation in domestic and commercial applications.  
1.1.1 To determine the Sound Power Level of a central vacuum at the power unit location refer to Test Method F2544.  
1.2 A-weighted sound pressure measurements are performed on a stationary vacuum cleaner in a semi-reverberant room. This test method determines sound power by a comparison method for small noise sources, that is, comparison to a broadband reference sound source.  
1.3 This test method describes a procedure for determining the approximate A-weighted sound power level of small noise sources. This test method uses a non-special semi-reverberant room.  
1.4 Results are expressed as A-weighted sound power level in decibels (referenced to one picowatt).  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Jul-2014
• ICS: 17.140.20 - Noise emitted by machines and equipment
• ICS: 97.080 - Cleaning appliances
• Technical Committee: F11 - Vacuum Cleaners
• Drafting Committee: F11.25 - Sound Measurement

Relations

• Replaces: ASTM F1334-12 - Standard Test Method for Determining A-Weighted Sound Power Level of Vacuum Cleaners
• Effective Date: 01-Aug-2014
• Referred By: ASTM F1411-11(2018) - Standard Practice for Presenting Selected Information on Vacuum Cleaners for Consumer Use
• Effective Date: 01-Aug-2014
• Referred By: ASTM F2609-11(2021) - Standard Test Method for Litter-Cleaning Effectiveness of Vacuum Cleaners
• Effective Date: 01-Aug-2014
• Referred By: ASTM F1284-22 - Standard Test Method for Evaluating Carpet Embedded Dirt Removal Effectiveness of Residential Central Vacuum Cleaning Systems
• Effective Date: 01-Aug-2014
• Referred By: ASTM F608-22 - Standard Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners
• Effective Date: 01-Aug-2014
• Referred By: ASTM F2608-15(2022) - Standard Test Method for Determining the Change in Room Air Particulate Counts as a Result of the Vacuum Cleaning Process
• Effective Date: 01-Aug-2014
• Referred By: ASTM F1409-16 - Standard Test Method for Straight Line Movement of Vacuum Cleaners While Cleaning Carpets
• Effective Date: 01-Aug-2014
• Referred By: ASTM F2544-11(2018) - Standard Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units
• Effective Date: 01-Aug-2014

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1334 − 14 An American National Standard
Standard Test Method for
Determining A-Weighted Sound Power Level of Vacuum
1
Cleaners
This standard is issued under the fixed designation F1334; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope C634Terminology Relating to Building and Environmental
Acoustics
1.1 This test method calculates the overall A-weighted
E177Practice for Use of the Terms Precision and Bias in
sound power level emitted by small portable upright, canister,
ASTM Test Methods
combination vacuum cleaners, backpack vacuum cleaners,
E691Practice for Conducting an Interlaboratory Study to
hard-floor machines, and central vacuum cleaner motorized
Determine the Precision of a Test Method
nozzles intended for operation in domestic and commercial
F608Test Method for Evaluation of Carpet Embedded Dirt
applications.
Removal Effectiveness of Household/Commercial
1.1.1 To determine the Sound Power Level of a central
Vacuum Cleaners
vacuumatthepowerunitlocationrefertoTestMethodF2544.
F655Specification for Test Carpets and Pads for Vacuum
1.2 A-weighted sound pressure measurements are per-
Cleaner Testing
formed on a stationary vacuum cleaner in a semi-reverberant
F2544Test Method for Determining A-Weighted Sound
room.This test method determines sound power by a compari-
Power Level of Central Vacuum Power Units
son method for small noise sources, that is, comparison to a
F2607Test Method for Measuring the Hard Surface Floor-
broadband reference sound source.
Cleaning Ability of Household/Commercial Vacuum
Cleaners
1.3 This test method describes a procedure for determining
3
the approximateA-weighted sound power level of small noise 2.2 ANSI Standards:
sources. This test method uses a non-special semi-reverberant ANSI S1.10Method for the Calibration of Microphones
room. ANSI S1.43Specifications for Integrating-Averaging Sound
Level Meters
1.4 Results are expressed asA-weighted sound power level
ANSI S12.51/ISO 3741Acoustics - Determination of sound
in decibels (referenced to one picowatt).
power levels of noise sources using sound pressure -
1.5 Thevaluesstatedininch-poundunitsaretoberegarded
Precision methods for reverberation rooms
as the standard. The values in parentheses are for information
ANSI S12.53/ISO 3743Acoustics - Determination of sound
only.
power levels of noise sources - Engineering methods for
1.6 This standard does not purport to address all of the
small, movable sources in reverberant fields
safety concerns, if any, associated with its use. It is the
ANSI S12.57/ISO 3747StandardAcoustics - Determination
responsibility of the user of this standard to establish appro-
of sound power levels of noise sources using sound
priate safety and health practices and determine the applica-
pressure - Comparison method in situ
bility of regulatory limitations prior to use.
3. Terminology
2. Referenced Documents
3.1 Definitions:
2
2.1 ASTM Standards: 3.1.1 population, n—the total of all of the units of the
particular model or type, or both, of vacuum cleaner being
tested.
1
ThistestmethodisunderthejurisdictionofASTMCommitteeF11onVacuum
3.1.2 population sample or sample, n—three or more test
Cleaners and is the direct responsibility of Subcommittee F11.25 on Sound
units, randomly taken from the population.
Measurement.
Current edition approved Aug. 1, 2014. Published August 2014. Originally
3.1.3 reference sound source, n—a standard source of
approved in 1991. Last previous edition approved in 2012 as F1334–12. DOI:
broadbandsoundwithacertifiedsetofsoundpoweremissions.
10.1520/F1334-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute, 11 W. 42nd St., 13th
the ASTM website. Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1334 − 14
3.1.4 source, n—a device that emits sound.This may be the
vacuum cleaner or a motorized nozzle.
3.1.5 test unit or unit, n—a single vacuum cleaner, nozzle,
or hard-floor machine of the model or type, or both, being
tested.
3.1.6 Unless otherwise indicated, definitions are in accor-
dance with Terminology C634.
4. Significance and Use
4.1 The test results enable the comparison of A-weighted
sound emission from vacuum cleaners or hard-floor machines
when tested under the condition o
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1334 − 12 F1334 − 14 An American National Standard
Standard Test Method for
Determining A-Weighted Sound Power Level of Vacuum
1
Cleaners
This standard is issued under the fixed designation F1334; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method calculates the overall A-weighted sound power level emitted by small portable upright, canister,
combination vacuum cleaners, backpack vacuum cleaners, hard-floor machines, and central vacuum cleaner motorized nozzles
intended for operation in domestic and commercial applications.
1.1.1 To determine the Sound Power Level of a central vacuum at the power unit location refer to Test Method F2544.
1.2 A-weighted sound pressure measurements are performed on a stationary vacuum cleaner in a semi-reverberant room. This
test method determines sound power by a comparison method for small noise sources, that is, comparison to a broadband reference
sound source.
1.3 This test method describes a procedure for determining the approximate A-weighted sound power level of small noise
sources. This test method uses a non-special semi-reverberant room.
1.4 Results are expressed as A-weighted sound power level in decibels (referenced to one picowatt).
1.5 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C634 Terminology Relating to Building and Environmental Acoustics
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
F608 Test Method for Evaluation of Carpet Embedded Dirt Removal Effectiveness of Household/Commercial Vacuum Cleaners
F655 Specification for Test Carpets and Pads for Vacuum Cleaner Testing
F2544 Test Method for Determining A-Weighted Sound Power Level of Central Vacuum Power Units
F2607 Test Method for Measuring the Hard Surface Floor-Cleaning Ability of Household/Commercial Vacuum Cleaners
3
2.2 ANSI Standards:
ANSI S1.10 Method for the Calibration of Microphones
ANSI S1.43 Specifications for Integrating-Averaging Sound Level Meters
ANSI S12.51/ISO 3741 Acoustics - Determination of sound power levels of noise sources using sound pressure - Precision
methods for reverberation rooms
ANSI S12.53/ISO 3743 Acoustics - Determination of sound power levels of noise sources - Engineering methods for small,
movable sources in reverberant fields
ANSI S12.57/ISO 3747 Standard Acoustics - Determination of sound power levels of noise sources using sound pressure -
Comparison method in situ
1
This test method is under the jurisdiction of ASTM Committee F11 on Vacuum Cleaners and is the direct responsibility of Subcommittee F11.25 on Sound Measurement.
Current edition approved June 1, 2012Aug. 1, 2014. Published June 2012August 2014. Originally approved in 1991. Last previous edition approved in 20112012 as
F1334 – 11.F1334 – 12. DOI: 10.1520/F1334-12.10.1520/F1334-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute, 11 W. 42nd St., 13th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1334 − 14
3. Terminology
3.1 Definitions:
3.1.1 population, n—the total of all of the units of the particular model or type, or both, of vacuum cleaner being tested.
3.1.2 population sample or sample, n—three or more test units, randomly taken from the population.
3.1.3 reference sound source, n—a standard source of broadband sound with a certified set of sound power emissions.
3.1.4 source, n—a device that emits sound. This may be the vacuum cleaner or a motoriz
...