ASTM D7042-12a
(Test Method)Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
Standard Test Method for Dynamic Viscosity and Density of Liquids by Stabinger Viscometer (and the Calculation of Kinematic Viscosity)
SIGNIFICANCE AND USE
5.1 Many petroleum products, and some non-petroleum materials, are used as lubricants and the correct operation of the equipment depends upon the appropriate viscosity of the liquid being used. In addition, the viscosity of many petroleum fuels is important for the estimation of optimum storage, handling, and operational conditions. Thus, the accurate determination of viscosity is essential to many product specifications.
5.2 Density is a fundamental physical property that can be used in conjunction with other properties to characterize both the light and heavy fractions of petroleum and petroleum products.
5.3 Determination of the density or relative density of petroleum and its products is necessary for the conversion of measured volumes to volumes at the standard temperature of 15°C.
SCOPE
1.1 This test method covers and specifies a procedure for the concurrent measurement of both the dynamic viscosity, η, and the density, ρ, of liquid petroleum products and crude oils, both transparent and opaque. The kinematic viscosity, ν, can be obtained by dividing the dynamic viscosity, η, by the density, ρ, obtained at the same test temperature.
1.2 The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to liquids for which primarily the shear stress and shear rate are proportional (Newtonian flow behavior).
1.3 The precision has only been determined for those materials, viscosity ranges, density ranges, and temperatures as indicated in Section 15 on Precision and Bias. The test method can be applied to a wider range of materials, viscosity, density, and temperature. For materials not listed in Section 15 on Precision and Bias, the precision and bias may not be applicable.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7042 − 12a
StandardTest Method for
Dynamic Viscosity and Density of Liquids by Stabinger
1
Viscometer (and the Calculation of Kinematic Viscosity)
This standard is issued under the fixed designation D7042; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* D975 Specification for Diesel Fuel Oils
D2162 Practice for Basic Calibration of Master Viscometers
1.1 Thistestmethodcoversandspecifiesaprocedureforthe
and Viscosity Oil Standards
concurrent measurement of both the dynamic viscosity, η, and
D2270 Practice for Calculating Viscosity Index from Kine-
thedensity, ρ,ofliquidpetroleumproductsandcrudeoils,both
matic Viscosity at 40 and 100°C
transparent and opaque. The kinematic viscosity, ν, can be
D4052 Test Method for Density, Relative Density, and API
obtained by dividing the dynamic viscosity, η, by the density,
Gravity of Liquids by Digital Density Meter
ρ, obtained at the same test temperature.
D6299 Practice for Applying Statistical Quality Assurance
1.2 The result obtained from this test method is dependent
and Control Charting Techniques to Evaluate Analytical
upon the behavior of the sample and is intended for application
Measurement System Performance
toliquidsforwhichprimarilytheshearstressandshearrateare
D6300 Practice for Determination of Precision and Bias
proportional (Newtonian flow behavior).
Data for Use in Test Methods for Petroleum Products and
1.3 The precision has only been determined for those Lubricants
D6617 Practice for Laboratory Bias Detection Using Single
materials,viscosityranges,densityranges,andtemperaturesas
indicated in Section 15 on Precision and Bias. The test method Test Result from Standard Material
D6708 Practice for StatisticalAssessment and Improvement
can be applied to a wider range of materials, viscosity, density,
and temperature. For materials not listed in Section 15 on of Expected Agreement Between Two Test Methods that
Purport to Measure the Same Property of a Material
Precision and Bias, the precision and bias may not be appli-
3
cable.
2.2 ISO Standards:
ISO5725 Accuracy(truenessandprecision)ofmeasurement
1.4 The values stated in SI units are to be regarded as
methods and results
standard. No other units of measurement are included in this
standard. ISO/IEC 17025 General Requirements for the Competence
of Testing and Calibration Laboratories
1.5 This standard does not purport to address all of the
4
safety concerns, if any, associated with its use. It is the 2.3 Other Documents:
responsibility of the user of this standard to establish appro- NIST Technical Note 1297 Guideline for Evaluating and
priate safety and health practices and to determine the Expressing the Uncertainty of NISTMeasurement Results
applicability of regulatory limitations prior to use.
3. Terminology
2. Referenced Documents
3.1 Definitions:
2
2.1 ASTM Standards:
3.1.1 density (ρ), n—mass per unit volume.
D445 Test Method for Kinematic Viscosity of Transparent
3.1.2 dynamicviscosity(η),n—theratiobetweentheapplied
and Opaque Liquids (and Calculation of Dynamic Viscos-
shear stress and rate of shear of a liquid.
ity)
3.1.2.1 Discussion—It is sometimes called the coefficient of
dynamic viscosity or, simply, viscosity. Thus, dynamic viscos-
1
This test method is under the jurisdiction of ASTM Committee D02 on
ity is a measure of the resistance to flow or to deformation of
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
a liquid under external shear forces.
Subcommittee D02.07 on Flow Properties.
Current edition approved Nov. 1, 2012. Published March 2013. Originally
ε1
approved in 2004. Last previous edition approved in 2012 as D7042–12 .
DOI:10.1520/D7042-12A.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from National Institute of Standards and Technology (NIST), 100
the ASTM website. Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7042 − 12a
3.1.2.2 Discussion—Thetermdynamicviscositycanalsobe 6.1.1 Viscosity Measurement—The Stabinger viscometer
used in
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: D7042 − 12 D7042 − 12a
Standard Test Method for
Dynamic Viscosity and Density of Liquids by Stabinger
1
Viscometer (and the Calculation of Kinematic Viscosity)
This standard is issued under the fixed designation D7042; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—Updated Table 2 editorially in August 2012.
1. Scope*
1.1 This test method covers and specifies a procedure for the concurrent measurement of both the dynamic viscosity, η, and the
density, ρ, of liquid petroleum products and crude oils, both transparent and opaque. The kinematic viscosity, ν, can be obtained
by dividing the dynamic viscosity, η, by the density, ρ, obtained at the same test temperature.
1.2 The result obtained from this test method is dependent upon the behavior of the sample and is intended for application to
liquids for which primarily the shear stress and shear rate are proportional (Newtonian flow behavior).
1.3 The precision has only been determined for those materials, viscosity ranges, density ranges, and temperatures as indicated
in Section 15 on Precision and Bias. The test method can be applied to a wider range of materials, viscosity, density, and
temperature. For materials not listed in Section 15 on Precision and Bias, the precision and bias may not be applicable.
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
D975 Specification for Diesel Fuel Oils
D2162 Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards
D2270 Practice for Calculating Viscosity Index from Kinematic Viscosity at 40 and 100°C
D4052 Test Method for Density, Relative Density, and API Gravity of Liquids by Digital Density Meter
D6299 Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measure-
ment System Performance
D6300 Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants
D6617 Practice for Laboratory Bias Detection Using Single Test Result from Standard Material
D6708 Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport
to Measure the Same Property of a Material
3
2.2 ISO Standards:
ISO 5725 Accuracy (trueness and precision) of measurement methods and results
ISO/IEC 17025 General Requirements for the Competence of Testing and Calibration Laboratories
4
2.3 Other Documents:
NIST Technical Note 1297 Guideline for Evaluating and Expressing the Uncertainty of NIST Measurement Results
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.07 on
Flow Properties.
Current edition approved April 15, 2012Nov. 1, 2012. Published July 2012March 2013. Originally approved in 2004. Last previous edition approved in 20112012 as
ε1
D7042–11a.–12 DOI:10.1520/D7042-12E01. DOI:10.1520/D7042-12A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Available from National Institute of Standards and Technology (NIST), 100 Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7042 − 12a
3. Terminology
3.1 Definitions:
3.1.1 density (ρ), n—mass per unit volume.
3.1.2 dy
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.